INA241A2IDGKR
Product Specifications
INA241A2IDGKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA241A2IDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA241A2IDGKR: the 20 V/V precision amplifier in an 8 pin VSSOP
The INA241A2IDGKR carries the same 20 V/V front end as the SOT-23 member of the family, in the wider 8 pin VSSOP body that many legacy motor control boards were laid out around. Common mode runs from minus 5 V to 110 V with a 120 V survival rating, offset is 10 uV maximum, gain error is 0.01 percent maximum, and DC rejection is 166 dB typical. The 1.1 MHz bandwidth holds at every gain, so the same part number family covers a torque loop and a fast overcurrent comparator.
The VSSOP body exists for two reasons. A 0.65 mm pitch is easier to inspect than the 0.5 mm pitch of the thin SOT-23, and the extra lead length gives a little more thermal relief on a board where the amplifier sits close to a shunt that is already dissipating. Neither of those shows up in the electrical table, and both matter in a factory that reflows a mixed board with 0402 passives around the part.
Key data for the INA241A2IDGKR
| Gain | 20 V/V fixed, from the five gain options of 10, 20, 50, 100 and 200 V/V |
| Common mode | Minus 5 V to 110 V operational and minus 20 V to 120 V survival, independent of the supply |
| Accuracy | Offset 10 uV maximum, 0.1 uV per degree, gain error 0.01 percent maximum, gain drift 1 ppm per degree |
| Rejection | 166 dB DC typical, 104 dB at 100 kHz and 89 dB at 1 MHz, with rejection built for 125 kHz switching |
| Speed | 1.1 MHz small signal bandwidth at all gains, 8 V per microsecond slew, settling to 1 percent in 1 us |
| Supply | 2.7 V to 20 V, 2.5 mA typical and 3 mA maximum quiescent, minus 40 C to 125 C |
Body, marking and reel data
| Body | DGK, 8 pin VSSOP at 3 mm by 4.9 mm, the widest of the three bodies in this family |
| Reel | 2500 pieces on a large reel for the DGK rows, against 3000 for the thin SOT-23 rows |
| Finish | NIPDAU at moisture level 2 with a one year floor life, so the reel has a bake clock |
| Marking | 2U7B on this gain and body, a code that does not spell the gain and is not readable after conformal coat |
| Footprint | Not interchangeable with the DDF body; the die is the same and the land pattern is not |
Where the VSSOP body still wins
Industrial motor drives, valve and actuator control, and cordless tool controllers built on older boards are the natural home. When a board already has a VSSOP land pattern from the previous generation of current sense amplifier, moving to the thin SOT-23 means a stencil change, a new aperture set and a re-qualification of the reflow profile, which is a week of process engineering for no electrical gain.
The limits are the ones that follow the 20 V/V gain. A 1 milliohm shunt gives 20 mV per amp, so a 75 A phase reaches 1.5 V and saturates the output on a 3.3 V rail; a 5 milliohm shunt reaches 15 A at the same swing. The rejection figures hold over the full common mode range, so the part is at home on a 48 V or 72 V pack, and the 20 V supply ceiling means it can run from the same 15 V gate drive rail as the bridge if that is convenient. Where the board is being moved between bodies, the amplifier cross reference note lists gain and body together, and our vendor consolidation note covers how we hold one qualified source across both bodies on a single line item.
Buyer questions on the INA241A2IDGKR
Can the DGK body take the same current as the DDF body? Yes, the current flows in the shunt and not in the amplifier, so the body only sets the thermal path for the amplifier's own dissipation, which is a few milliwatts.
Why would a new board pick the VSSOP? Inspection and rework. At 0.65 mm pitch a touch up with an iron is possible; at 0.5 mm pitch on a thin body it usually is not.
Does the reel size difference cause a problem? Only in feeder setup. 2500 against 3000 changes how many boards a reel covers, and a line that plans on 3000 will run short before the scheduled reel change.
Availability and ordering notes
The DGK rows are active in the current addendum at 2500 pieces on a large reel at moisture level 2 with a one year floor life. The ordering table in this revision prints the package and quantity columns one row out of step with the part numbers, so a reader looking at the row below can see a VSSOP suffix beside a SOT-23 quantity. The decode is reliable and the columns are not, which is why we quote this family by body and reel rather than by position in the table. Where a line runs both bodies, the two reels need separate feeder positions and separate labels, and that detail is recorded on the power management cross reference sheet we keep for the family.