Contact Us

INA241A2IDDFR

Brand: Texas Instruments
Texas Instruments INA241A2IDDFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA241A2IDDFR — Power Management & Signal Chain | Superb Automation

INA241A2IDDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA241A2IDDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA241A2IDDFR: 20 V/V version of the 110 V precision amplifier

The INA241A2IDDFR is the 20 V/V member of the INA241A family in the 8 pin SOT-23-THIN body. Everything around the gain is shared with the rest of the family: minus 5 V to 110 V of operational common mode, 120 V survival, 10 uV maximum offset, 0.01 percent maximum gain error, 166 dB typical DC rejection, 1.1 MHz bandwidth and 8 V per microsecond of slew. The gain step from 10 to 20 V/V doubles the output for the same shunt drop, which halves the shunt needed for a given signal and therefore halves the heat in the phase leg.

That is the whole argument for a 20 V/V part in a motor drive. A 40 A phase through a 0.5 milliohm shunt produces 20 mV, which at 10 V/V is a 200 mV signal sitting close to the offset floor and at 20 V/V is 400 mV with twice the margin. The shunt dissipation is unchanged; what changes is how much of the signal the amplifier can hand to the converter before the noise floor and the offset start to matter.

Key data for the INA241A2IDDFR

Gain20 V/V fixed, one of five options from 10 to 200 V/V sharing one body and pinout
Common modeMinus 5 V to 110 V operational, minus 20 V to 120 V survival, independent of the 2.7 V to 20 V supply
AccuracyOffset 10 uV maximum, 0.1 uV per degree of drift, gain error 0.01 percent maximum, 1 ppm per degree
Rejection166 dB DC typical, 104 dB at 100 kHz, 89 dB at 1 MHz, PWM rejection built for switching to 125 kHz
Speed1.1 MHz at all gains, 8 V per microsecond slew, 1 us settling to 1 percent of a step
Supply2.7 V to 20 V, 2.5 mA typical and 3 mA maximum, minus 40 C to 125 C

Body, marking and reel data

BodyDDF, 8 pin SOT-23-THIN at 2.9 mm by 2.8 mm, the same land pattern as every other gain in the family
Reel3000 pieces on a large reel for the DDF rows at moisture level 1, unlimited floor life
FinishNIPDAU plated leads, compatible with a lead free reflow profile at 260 C
Marking2PI3 on this gain and body, which does not spell the gain and cannot be read after potting
Gain family10, 20, 50, 100 and 200 V/V in both the A and B accuracy tiers, all in the same footprint

Choosing between 10 and 20 V/V

The decision is arithmetic before it is anything else. Take the peak current, the shunt, the output swing available on the converter rail and the offset, and see which gain keeps the smallest current of interest above the offset. A 3.3 V converter with the output biased at mid rail has about 1.5 V of swing in each direction, so a 20 V/V part accepts 75 mV of shunt drop, which is 15 A through a 5 milliohm shunt or 75 A through a 1 milliohm shunt. The same 1.5 V at 10 V/V accepts 150 mV, twice the current on the same shunt.

The second consideration is the PWM rejection requirement. Both gains show the same rejection, so a higher gain does not buy better immunity, but it does amplify whatever residue reaches the input, which is why the input filter and the symmetry of the two shunt traces matter more as the gain rises. The third is the reference pins: the output is level shifted by REF1 and REF2, and a bidirectional measurement needs both set to mid rail rather than to ground, otherwise the negative half of the waveform clips. Where a board is choosing between gains on the same footprint, the amplifier cross reference note tabulates the options, and the pin to pin cross reference record confirms that a gain change needs no board revision.

Buyer questions on the INA241A2IDDFR

Does a higher gain reduce the input range? Not the common mode range, which is set by the input stage and stays at 110 V. It reduces the differential range that keeps the output inside its swing, so the measurable current at the top end falls as the gain rises.

Is the A2 gain available in the automotive grade? Yes, as a separate Q1 family string. The industrial and automotive addenda are different documents and the Q1 packing rows have to be read from the automotive one.

Why is the bandwidth the same at every gain? The architecture sets the bandwidth ahead of the gain stage, so the small signal response does not collapse as gain rises. That is unusual and it is the reason the family is used in loops, not only in comparators.

Availability and ordering notes

The DDF rows for this family are active at 3000 pieces on a large reel with NIPDAU at moisture level 1. Because five gains and three bodies share one ordering table, and because this revision prints the package and quantity columns shifted by a row, the safe practice is to read the part number decode rather than the adjacent columns. The marking on the body names the gain and body but not the accuracy tier, so an A part and a B part of the same gain are indistinguishable by eye after reflow. Kits that carry both tiers on one line are separated and labelled at the kitting service stage, which is where a mixed reel would otherwise reach the placement machine.