Contact Us

INA241A1IDDFR

Brand: Texas Instruments
Texas Instruments INA241A1IDDFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA241A1IDDFR — Power Management & Signal Chain | Superb Automation

INA241A1IDDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA241A1IDDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA241A1IDDFR: 110 V bidirectional amplifier with a 10 V/V gain

The INA241A1IDDFR is the lowest gain member of the INA241A family, a bidirectional current sense amplifier that works from 5 V to 110 V of common mode with a survival range of minus 20 V to 120 V. The A version carries the tight accuracy rows: offset 10 uV maximum with 0.1 uV per degree of drift, and gain error 0.01 percent maximum with 1 ppm per degree. On a 10 V/V gain that gain error is 100 uV per volt of output, which is below the offset contribution at low currents, so the two errors trade places through the range rather than one dominating.

The part is built for switching systems. Enhanced PWM rejection keeps the output clean when the common mode moves, the family supports switching frequencies to 125 kHz, and the small signal bandwidth is 1.1 MHz at every gain. DC common mode rejection is 166 dB typical, 104 dB at 100 kHz and 89 dB at 1 MHz. Supply range is 2.7 V to 20 V, which is wide enough to run from a 5 V housekeeping rail or from the 12 V rail the bridge is already using.

Key data for the INA241A1IDDFR

Gain10 V/V fixed; the family offers 10, 20, 50, 100 and 200 V/V in the same body and pinout
Common modeMinus 5 V to 110 V operational, minus 20 V to 120 V survival, independent of the 2.7 V to 20 V supply
AccuracyOffset 10 uV maximum, drift 0.1 uV per degree, gain error 0.01 percent maximum, gain drift 1 ppm per degree
Rejection166 dB DC typical, 104 dB at 100 kHz, 89 dB at 1 MHz, all with the output loaded lightly
Speed1.1 MHz at all gains, 8 V per microsecond slew, settling to 1 percent in 1 us
Supply2.7 V to 20 V, 2.5 mA typical and 3 mA maximum quiescent, minus 40 C to 125 C

Body, marking and reel data

BodyDDF, 8 pin SOT-23-THIN at 2.9 mm by 2.8 mm, the smallest of the three bodies offered
Reel3000 pieces on a large reel for the DDF rows, against 2500 for the DGK VSSOP rows
FinishNIPDAU at moisture level 1 on the DDF rows, so no floor life clock and no bake
Marking2PH3 on this gain and body, a four character code that does not spell the gain
Version splitThe A version is the 0.01 percent gain error part, the B version the 0.1 percent part at a lower price

Where a 10 V/V front end on 110 V belongs

Motor drives, solenoids and actuators, injection moulding machines, cordless tools, medical cordless tools and drone propeller speed control are the listed applications. A 110 V common mode is what a 48 V or 72 V battery pack reaches during a switching transient, and the surge rating of 120 V is what covers a load dump on a vehicle rail. At 10 V/V a 1 milliohm shunt gives 10 mV per amp, so a 5 A phase produces 50 mV and a 40 A phase produces 400 mV, both inside the linear range of a 3.3 V converter with the output centred by the reference pins.

The trade against a higher gain is resolution at low current. A 10 V/V front end with 10 uV of offset cannot resolve below about 1 mA through a 1 milliohm shunt, which is fine for a motor phase and not fine for a standby measurement. That is why the family publishes five gains: the gain follows the shunt and the current range, and a board that needs both a phase current and a quiescent current uses two parts or one part plus a gain stage. Where a line is switching between the A and B versions on cost, the amplifier cross reference note lists both accuracy tiers side by side, and the drone and UAV components note covers the vibration and thermal conditions that a propeller controller adds to the electrical specification.

Buyer questions on the INA241A1IDDFR

Is the A version worth the price difference over B? It is 100 times tighter on gain error and 15 times tighter on offset. For a current loop that has to hold torque at low speed the A version removes a calibration step; for a protection comparator the B version is enough.

Can the part run from the 12 V rail? Yes, the supply range reaches 20 V, so the same rail that feeds the gate driver can feed the amplifier, which avoids a sequencing question at power up.

Does the 110 V rating include the negative side? The operational range is minus 5 V to 110 V, so a small negative excursion is inside the specification and a full reverse battery is covered only by the 120 V survival rating for the duration the vendor states.

Availability and ordering notes

The DDF rows for this family are active at 3000 pieces on a large reel with NIPDAU at moisture level 1, and the DGK VSSOP rows are published at 2500 on a large reel at moisture level 2. One caution on this revision: the ordering table prints the package, quantity and moisture columns shifted by one row relative to the part numbers, so a reader who takes the row at face value can see a VSSOP suffix beside a SOT-23 package. The part number decode is the reliable guide, DDF for the SOT-23-THIN and DGK for the VSSOP, and any purchase order should name the body explicitly. Where a build is booking capacity ahead of a ramp, the power management cross reference note records the gain and body combinations we can hold in stock.