Contact Us

INA236AIDDFR

Brand: Texas Instruments
Texas Instruments INA236AIDDFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA236AIDDFR — Power Management & Signal Chain | Superb Automation

INA236AIDDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA236AIDDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA236AIDDFR: 48 V, 16 bit current, voltage and power monitor with a 1.2 V compatible I2C interface

INA236AIDDFR is a digital power monitor with a programmable shunt range that reports current, bus voltage and power in engineering units over a 1.2 V compatible I2C bus in a SOT-23-THIN body of 8 pins. It runs from a 1.7 V to 5.5 V supply, draws 300 uA while converting and 2.2 uA in standby, and measures a shunt drop of either 20.48 mV or 81.92 mV full scale on a common mode from minus 0.3 V to 48 V. Offset is 5 uV maximum and gain error is 0.1 per cent maximum, both tighter than the older 36 V monitors in the same register family.

Order code and package

INA236AIDDFRSOT-23-THIN DDF body, 8 pins, 3000 pieces on a large reel, Active, RoHS Yes, NIPDAU finish, moisture level 1 with unlimited floor life, part marking 2QRF, minus 40 to plus 125 degrees
INA236AIDDFR.Athe same DDF reel and the same marking printed as a second row of the same addendum
INA236AIYFFRDSBGA body, 8 pins, 0.745 mm by 1.508 mm, 3000 pieces on a large reel, the option when the board has no room for a leaded package
INA236AIDGSTthe small reel route through the VSSOP body when a prototype needs twenty pieces rather than three thousand
Catalogue notethe addendum prints the DDF string at moisture level 1, so the reel does not need a dry pack schedule before reflow

Electrical parameters that decide the application

Supply range1.7 V to 5.5 V, which is the lowest in this family and the reason the part appears on 1.8 V rails
Common mode rangeminus 0.3 V to 48 V, independent of the supply voltage, with the bus measured on the IN minus pin
Shunt full scale81.92 mV with the range bit clear and 20.48 mV with it set, giving four times the resolution on the same shunt
Offset voltage5 uV maximum, which is the tightest figure in the 16 bit monitors and five times better than the 25 uV of the 36 V part
Gain error0.1 per cent maximum, against 0.3 per cent on the older monitor
Common mode rejection136 dB minimum and 150 dB typical from minus 0.3 V to 48 V across the temperature range
Input bias current10 nA maximum while measuring current, which is what allows a shunt in the tens of milliohm range without a buffer
Resolution16 bit on the shunt, bus voltage and power registers, with the current scale set by the calibration register
Conversion time140 us to 8.244 ms per channel, selected separately for shunt and bus voltage
Averaging1 to 1024 conversions rolled into the output registers, with the conversion ready flag rising only after the average is complete
Addressingtwo device address options with four selectable pins, giving sixteen addresses, plus a general call that synchronises conversion across devices
Alertover current, under current, over voltage and under voltage limits, each with its own threshold register
Power and standby300 uA typical while converting, 2.2 uA typical in standby, which is the figure that keeps a battery product alive

Family variants and how they differ

20.48 mV against 81.92 mVthe narrow range gives four times the resolution on the same shunt, but a 1 milliohm shunt then saturates at just over 20 A, so the shunt and the range have to be chosen together
INA236 against INA230the INA236 has the tighter offset and gain figures and the 1.7 V supply, while the INA230 offers a 36 V bus on a 16 pin body with 330 uA of supply current
INA236 against INA228the INA228 adds energy and charge accumulation and reaches 85 V at 20 bit, at a larger supply current
Standby behaviourthe 2.2 uA standby current is a real state with the registers retained, not a power down, so a host can wake the device and read the last result
Bus measurement pointthe bus voltage is taken at the IN minus pin, which is the load side of the shunt, so the reading is the load voltage rather than the supply voltage

Points to check before this part goes on a BOM

The 5 uV offset is the headline number and it changes what shunt value is usable. On a 1 milliohm shunt that is 5 mA of offset error, so a 10 A rail reads within 0.05 per cent before gain error is considered. On a 10 milliohm shunt the same offset is 0.5 mA, which is the reason a low current product uses a larger shunt and the narrow range rather than a small shunt and the wide range.

The bus voltage is measured at the load side of the shunt, which is a deliberate difference from a monitor that reads at the supply pin. On a rail with a 100 mV shunt the two points differ by 100 mV, and a battery product that reports its own terminal voltage wants the load side, while a supply that reports its output wants the other. The datasheet is explicit about which pin, and a board that assumed the wrong one is off by the shunt drop.

The 1.7 V supply floor is what puts this part on low voltage rails. Most digital monitors stop at 2.7 V, so a 1.8 V core rail cannot power its own monitor from the rail it is measuring, and this part can. The 1.2 V compliant I2C is the matching half of that: the bus can be pulled to 1.2 V while the device itself runs from 1.8 V.

Averaging runs to 1024 samples, which is enough to turn a noisy converter output into a stable reading. The cost is time: 1024 samples at 8.244 ms is 8.4 seconds per update, so the highest averaging setting belongs on a slowly varying battery current, not on a load that changes every millisecond. The conversion ready flag is what the host should wait on rather than a timer.

The alert registers cover four conditions rather than one. Over current and under current come from the shunt path, over voltage and under voltage from the bus path, and each has its own limit register and its own latch behaviour. That is the difference between a monitor that reports a fault after the fact and one that can drive a protection pin.

The general call address is easy to overlook. It lets one host synchronise conversion across every device on the bus so that the readings refer to the same instant, which matters on a multi rail board where the sum of the rail powers is being compared against a total. Without it the readings are separated by however long the host takes to walk the bus.

Choosing the range bit and the shunt together

With the narrow range and a 2 milliohm shunt the full scale is 10.24 A, and with the wide range on the same shunt it is 40.96 A. A product that expects a 15 A peak has to take the wide range with a 2 milliohm shunt or the narrow range with a 1 milliohm shunt, and the second choice doubles the offset error in milliamps while halving the dissipation. There is no setting that gives both resolution and headroom on one resistor.

What the standby state is worth on a battery product

300 uA of conversion current on a 3.7 V cell is 1.1 mW, which is more than a sleeping microcontroller draws on the same board. The 2.2 uA standby state is 8 uW, and the registers keep their last value, so a product that samples its own current once a second can spend most of its life in standby and still report a fresh reading on wake.

Where this order code fits

Mobile phones, smart speakers, wearables, battery chargers, power management blocks, battery cell monitors and rack servers are the applications the vendor names, and the low supply floor is what puts the same part on a 1.8 V rail and on a 5 V rail without a second order code. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Amplifier Cross Reference page.

Questions buyers ask

Can it run from the 1.8 V rail it is measuring? Yes. The supply floor is 1.7 V and the I2C interface is compliant down to 1.2 V.

Does it need a separate supply for the bus? No. The common mode reaches 48 V independently of the 1.7 V to 5.5 V supply.

Does it measure energy over time? No. It reports current, voltage and power. Energy accumulation is in the INA228 and INA229.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.