INA231AIYFFR
Product Specifications
INA231AIYFFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA231AIYFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA231AIYFFR: 16 bit current monitor in a 1.65 mm wafer level body
The INA231AIYFFR is a 28 V, 16 bit current and power monitor in a 12 bump wafer level package that measures 1.65 mm by 1.39 mm by 0.62 mm. It reports shunt voltage, bus voltage and power over an I2C bus that is compliant down to 1.8 V logic, and it adds an ALERT pin that asserts when a reading leaves a programmed window, which is the feature that turns a monitor into a supervisor without host polling. Gain error is 0.5 percent maximum and offset is 50 uV maximum, with a 2.5 uV step on the shunt channel and an input impedance of 830 kOhm on the bus pin.
The A version starts converting as soon as it is powered, and the B version starts in a low current power down state and waits for a command. That single difference decides which one a battery product wants: a phone that boots with a fuel gauge already sampling does not want an extra 330 uA drawn from the moment the cell is connected, while a server that needs a rail reading within a few milliseconds of power good does. Both versions are specified from minus 40 C to 125 C and both run from 2.7 V to 5.5 V.
Key data for the INA231AIYFFR
| Bus range | 0 V to 28 V on the bus pin, high side or low side placement, independent of the 2.7 V to 5.5 V supply |
| Resolution | 16 bit converter, 2.5 uV per step on the shunt channel, 1.25 mV per step on the bus channel |
| Accuracy | Gain error 0.5 percent maximum, offset 50 uV maximum over the full temperature range |
| Timing | Conversion time from 140 us to 8.244 ms, averaging from 1 to 128 samples, both set in the configuration register |
| Alert | Programmable over and under threshold with a dedicated open drain ALERT pin, plus a conversion ready flag |
| Supply | 2.7 V to 5.5 V, 330 uA typical and 420 uA maximum, 1.8 V compliant I2C with 16 addresses |
Body, marking and reel data
| Body | YFF, 12 bump DSBGA at 1.65 mm by 1.39 mm by 0.62 mm; the YFD body is the same footprint at 0.40 mm of height |
| Reel | 3000 pieces on a large reel for the R suffix on both bodies |
| Finish | SNAGCU bumps at moisture level 1, unlimited floor life, no bake before reflow |
| Marking | Two lines of laser marking on the bump side, readable only at a shallow angle and not a substitute for the reel label |
| Versions | The A version starts converting at power up, the B version starts in power down, and the suffix letter is the only difference in the order code |
Where a wafer level monitor fits
Smartphones, tablets, servers, notebooks, chargers and bench supplies are the listed applications, and they share a constraint that a 3 mm by 5 mm package does not satisfy: the monitor has to sit on a flex or a main board where the height of the tallest part beside it is the battery connector. A 0.62 mm body drops under that ceiling, and the YFD row at 0.40 mm drops further for a stack that is already tight.
The practical limit of a 28 V part is that it covers a 24 V rail and nothing above it, so a 48 V telecom plant needs a different member of the family. The second limit is thermal: a 12 bump body has almost no copper to spread into, so the trace from the shunt to the IN pins carries both the measured current and the heat, and the two IN traces have to be symmetrical to keep the shunt drop from being read as an offset. Where a line is switching between this monitor and the analog output amplifiers that do the same job, the amplifier cross reference note lists the gain and common mode of both, and the pin to pin cross reference note records which bodies share a land pattern so a second source does not need a new stencil.
Buyer questions on the INA231AIYFFR
Is the A version a drop in for the B version? Electrically and mechanically yes, and the register map is identical. The difference is the state of the configuration register after power up, so a host that assumes conversions are already running will read zeros on the B version until it writes the configuration.
Can eight of these sit on one bus? The part offers 16 addresses from two address pins, which covers a multi rail board with room to spare. The limit is usually the pull up resistor and the bus capacitance, not the address count.
What does the ALERT pin actually save? It saves polling. A host that has to read three registers every millisecond to catch an overcurrent event burns bus time and wake cycles; with a threshold set, the pin asserts and the host reads on the interrupt instead.
Availability and ordering notes
The catalogue string INA231AIYFFR is active at 3000 pieces on a large reel. Three rows in this addendum are worth reading carefully before a purchase order is placed. The .B row of INA231AIYFFR is printed Obsolete while the plain row and the .A row are active, so a distributor holding an older reel label may be quoting a superseded row. The .A row is active with SNAGCU bumps at moisture level 1. And the INA231AIYFFT row prints the YFD body against a T suffix that elsewhere in the table means a small reel, which is a column shift in the document rather than a body change; the body has to be named separately on any order that mixes YFF and YFD. Where a build is being pulled forward against a long lead time, the component lead time solutions note covers what can be substituted without a board change.