Contact Us

INA2180A3IDSGR

Brand: Texas Instruments
Texas Instruments INA2180A3IDSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2180A3IDSGR — Power Management & Signal Chain | Superb Automation

INA2180A3IDSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2180A3IDSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2180A3IDSGR: the dual 100 V/V monitor in a WSON-8

The INA2180A3IDSGR is the WSON 8 pin body of the dual INA180 family at 100 V/V. Electrically it matches the VSSOP version: two independent channels, a common mode window from 0.2 V below ground to 26 V above, a 2.7 V to 5.5 V supply, 150 uV of offset at 0 V common mode and 500 uV at 12 V, 1 uV per degree of drift, 1 percent gain error and 150 kHz of bandwidth at gain 100. The dual package draws 500 uA maximum and needs one 0.1 uF bypass capacitor at the supply pin.

The difference is the package and the packing. The WSON 8 body is 2 mm by 2 mm with an exposed pad, which gives a short thermal path into the ground plane and a smaller loop area for the shunt connections, and it ships 2500 pieces on a large reel with NIPDAU or SN finish at moisture level 1, marking 25GY. Moisture level 1 with unlimited floor life is worth stating explicitly, because it removes the bake step that most 8 pin packages still require.

Key data for the INA2180A3IDSGR

Gain100 V/V per channel, four options from 20 to 200 in the same dual family
InputCommon mode minus 0.2 V to plus 26 V per channel, independent of the 2.7 V to 5.5 V supply
AccuracyOffset 150 uV maximum at 0 V and 500 uV at 12 V, 1 uV per degree drift, 1 percent gain error
Bandwidth150 kHz at gain 100, 355 kHz at gain 20, 105 kHz at gain 200, all with a 10 pF load
Supply2.7 V to 5.5 V, 500 uA maximum for both channels, 0.1 uF bypass
PackageWSON 8 pin, 2 mm by 2 mm with exposed pad, a different land pattern from the VSSOP body

Body, marking and reel data

BodyDSG, WSON 8 pin, 2 mm by 2 mm with an exposed thermal pad
Reel2500 pieces on a large reel, which is 500 fewer than the VSSOP row of the same die
FinishNIPDAU or SN, moisture level 1 at 260 C with unlimited floor life
Marking25GY on the A3 WSON row, four characters that identify the dual die and the gain
TemperatureMinus 40 C to 125 C, the same specification as the rest of the family

Exposed pad, loop area and the shunt connection

A current sense amplifier measures millivolts, so the loop between the shunt terminals and the input pins is part of the measurement. The WSON body with its exposed pad lets the two input traces run on the same layer as the shunt and return directly under the die, which is the shortest path available in an 8 pin package. On a board that has to pass a conducted emissions scan, that loop area is also an antenna, and shrinking it helps both problems at once.

The exposed pad is electrically the die substrate in most of this family, tied to the negative supply, so it goes to the ground plane with vias rather than to a quiet node. That is the one placement rule that matters more than the rest. Where a project is comparing the two bodies, our pin to pin cross reference records which of them can share a land and which cannot, and the incoming inspection plan covers the marking and reel checks for the small body sizes.

Buyer questions on the INA2180A3IDSGR

Is 2500 pieces the only packing? For this string yes, the addendum prints 2500 on a large reel. A production run of 10,000 boards needs four reels, which is a normal kit size for a small body.

Can the WSON and the VSSOP rows be mixed on one panel? Not on the same land pattern. They are two different footprints with the same die, so the board decides the body before the gain is chosen.

Does the exposed pad have to be soldered? Yes. It is both the thermal path and the electrical reference, and a void under it shows up as offset drift on a hot board rather than as an open circuit.

Availability and ordering notes

The A3 WSON row is active at 2500 pieces with NIPDAU or SN finish at moisture level 1, marking 25GY, while the A4 row of the same body prints level 2 with a one year floor life and an obsolete lettered counterpart. Two rows of one family therefore carry different moisture classes, which is read per row and not per family. We confirm the gain, the body and the date code on receipt and record the moisture class on the date code management note. A 2500 piece reel also means a kit for a 10,000 board build is four reels, one carton and one label.