Contact Us

INA216A3YFFR

Brand: Texas Instruments
Texas Instruments INA216A3YFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA216A3YFFR — Power Management & Signal Chain | Superb Automation

INA216A3YFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA216A3YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA216A3YFFR: 100 V/V zero drift current shunt monitor in the four ball chip scale package

INA216A3YFFR is a unidirectional high side current shunt monitor with a fixed 100 V/V gain, in the smallest body the family offers in a DSBGA body of 4 pins. It senses the drop across a shunt at common mode from 1.8 V to 5.5 V, which is the supply window itself, uses a zero drift input stage with a plus or minus 30 uV offset limit and a plus or minus 0.2 per cent gain error, and draws 13 uA typical with 25 uA maximum. The four ball chip scale body is 1.17 mm by 0.765 mm, which is the reason the part exists: it fits inside the footprint of the shunt it measures.

Order code and package

INA216A3YFFRDSBGA YFF body, 4 balls, 3000 pieces on a large reel, Active in the addendum dated 7 October 2026, SNAGCU ball material, marking OY, minus 40 to plus 125 degrees
INA216A3YFFR.Athe .A revision row of this exact string is printed Obsolete in the same addendum, so a quote against the .A suffix is quoting a closed status while the plain row is still Active
INA216A3RSWRUQFN RSW body, 10 pins, 3000 pieces on a large reel, marking SPJ, which is the body to use where a 0.4 mm pitch chip scale part is outside the assembly capability of the line
INA216A3RSWTthe same RSW body on a small reel, whose quantity column in the addendum is blank, so the reel size has to be confirmed with the vendor rather than assumed
INA216A2YFFRthe 50 V/V member in the same four ball body on a 250 piece small reel, marking OX, which is the sibling to compare when the 100 V/V gain gives too much output for the shunt in use

Electrical parameters that decide the application

Common mode range1.8 V to 5.5 V, which is the supply range itself, so the part measures a bus that is the same rail that powers it
Absolute maximum on the inputsminus 5.5 V to plus 5.5 V, which is the hard limit that rules out any bus above 5.5 V
Supply1.8 V to 5.5 V single rail, 13 uA typical and 25 uA maximum quiescent current
Offset voltageplus or minus 30 uV maximum referred to the input, from a zero drift stage
Gain errorplus or minus 0.2 per cent maximum, which is five times tighter than the low cost monitors in the same class
Gain100 V/V on the A3 member, against 25, 50 and 200 V/V on A1, A2 and A4
Common mode rejection90 dB minimum and 108 dB typical, and the table notes that this equals the supply rejection because the common mode is the supply
Bandwidth5 kHz on the A3 member with a 10 pF load, against 20 kHz on A1, 10 kHz on A2 and 2.5 kHz on A4
Input bias current3 uA maximum on the inverting input, which is large against the picoamp class parts and has to be counted in the shunt error
Outputbuffered voltage output that needs no external amplifier, with 42 ohm of output impedance
Output swingto within 1 to 2 mV of the supply rail at the top and to the ground rail at the bottom
Temperatureminus 40 to plus 125 degrees

Family variants and how they differ

Gain against bandwidththe four gain members have four different bandwidths and the highest gain is the slowest: 20 kHz at 25 V/V, 10 kHz at 50 V/V, 5 kHz at 100 V/V and 2.5 kHz at 200 V/V, so raising the gain for resolution costs response time
INA216 against INA186the INA186 spans 40 V of common mode and runs at 48 uA, while this part is limited to its own supply and runs at 13 uA, so the choice is made by the bus voltage before anything else
INA216 against INA180the INA180 covers 26 V of common mode and 350 kHz for about the same money, so the reason to use this part is the 1.17 mm body and the 13 uA current rather than the electrical performance
Unidirectional sensingthe family measures in one direction only, so a load that regenerates needs a different part or a reference offset that this device does not have
Body optionsthe four ball YFF and the ten pin RSW are the same silicon, and the RSW body is the one for a line that cannot place a 0.4 mm pitch chip scale part

Points to check before this part goes on a BOM

The common mode window equals the supply, which is the defining limitation of this part. It measures a bus that is at or below 5.5 V, so it is a 3.3 V and 5 V part and nothing else. A 12 V rail, a 24 V rail and a 48 V rail are all outside it, and the absolute maximum of 5.5 V on the inputs means a 12 V rail does not merely read wrong, it destroys the part. This is the single fact that decides whether the part can be used at all.

The 5 kHz bandwidth on the 100 V/V member is slow for a current monitor and it is deliberate. The part is built for a battery gauge or a power management block that samples a current a few times a second, and the low bandwidth is what comes with 13 uA of supply current and a zero drift stage. An overcurrent protection loop built on this output will respond in a quarter of a millisecond at best, which is a lifetime for a short circuit.

The 3 uA input bias current is three orders of magnitude above the picoamp parts and it flows in the shunt. On a 10 milliohm shunt that is 30 nV and irrelevant. On a 10 kOhm shunt used for a microamp measurement it is 30 mV, which is larger than the full scale signal. This part is therefore for a low value shunt at a moderate current, and the INA186 with its 0.5 nA is the part for a high resistance shunt.

The gain error of 0.2 per cent and the offset of 30 uV are good numbers for a part this small, and both are referred to the input. At 100 V/V a 30 uV offset is 3 mV at the output, which on a 1.8 V converter input is 0.17 per cent of full scale, so the offset and the gain error are of the same order at full scale and the offset dominates below a fifth of full scale.

The .A revision of this exact order code is Obsolete while the plain row is Active. That pattern appears on several rows in this addendum and it is not a mistake: the .A row is an older revision that the vendor has closed, and a distributor that quotes .A is selling either old stock or a string it has not checked. An incoming inspection should compare the reel label against the plain string rather than accept the suffix as an equivalent.

The output impedance of 42 ohm is high enough to matter for a sampling converter. A switched capacitor input draws a charge spike every conversion, and 42 ohm with the converter input capacitance forms a settling time that has to fit inside the sampling window. Where the converter samples fast, a unity gain buffer between the monitor and the converter is the usual addition, and the datasheet application section shows the arrangement.

Where a chip scale current monitor earns its place

The four ball body is 1.17 mm by 0.765 mm, which is smaller than the 0805 shunt it measures. On a phone or a wearable the board area for current monitoring is the difference between shipping the feature and dropping it, and a part that fits beside the shunt with two traces and no other components is the only version that fits at all.

The cost of that size is the body's assembly requirement. A 0.4 mm pitch chip scale part needs a line that can place and inspect it, and a contract assembler without that capability will either decline or place it badly. The ten pin RSW body is the same silicon in a package that any line can place, and the decision between them is a process question rather than an electrical one.

Reading the 42 ohm output

The buffered output is specified into a 10 pF load, and the bandwidth figures are quoted with that load. A 100 pF cable or a converter input with a large sampling capacitor slows the response further, and the 5 kHz figure on the 100 V/V member becomes a kilohertz or less. For a gauge that samples slowly this is invisible, and for anything faster it is the limiting term.

Where this order code fits

Notebook computers, cell phones, telecom line cards, power management blocks and battery chargers are the applications the vendor names, and all of them measure a current on a rail that is at or below 5.5 V inside a board area measured in millimetres. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

Can it measure a 12 V rail? No. The common mode window and the absolute maximum are both 5.5 V, so a 12 V bus exceeds the ratings and will damage the input stage.

Why is the bandwidth only 5 kHz? The chopper stabilised low current stage trades bandwidth for offset and quiescent current, and the highest gain member is the slowest at 5 kHz.

Is the .A revision the same part? No. The .A row is printed Obsolete while the plain row is Active, so the plain string is the one to order.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.