INA205AIPWR
Product Specifications
INA205AIPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA205AIPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA205AIPWR: 100 V/V monitor with two comparators and a reference output
The INA205AIPWR is the 100 V/V member of the INA203 to INA205 family, a high side current shunt monitor that carries two open drain comparators, two 0.6 V references and, on the 14 pin bodies, a 1.2 V reference output. It reads a shunt between 16 V below ground and 80 V above it from a 2.7 V to 18 V supply, delivers 100 times the shunt drop as a voltage, and runs at 200 kHz with a 5 pF load. Quiescent current is 1.8 mA, and total error is 3.5 percent maximum over temperature.
Two comparators is the distinguishing feature. Comparator one latches, which preserves a fast fault for a controller that polls slowly. Comparator two has a user programmable delay, which is what a system needs when a current spike should be ignored for a few milliseconds but a sustained overload should not. On the 14 pin package the internal references can be overridden from outside, so a system with its own reference voltage can keep everything on one reference and avoid a second tolerance stack.
Key data for the INA205AIPWR
| Gain | 100 V/V, with 20 V/V as INA203 and 50 V/V as INA204 in the same family |
| Input | Common mode minus 16 V to plus 80 V, unidirectional, independent of the supply |
| Comparators | Two open drain outputs, one latching, one with a programmable delay, both against a 0.6 V reference |
| Reference | Internal 0.6 V for the trip points, external override on the 14 pin body, 1.2 V output available |
| Bandwidth | 200 kHz at gain 100 with a 5 pF load, 500 kHz at gain 20 and 300 kHz at gain 50 |
| Supply | 2.7 V to 18 V, 1.8 mA maximum quiescent current, minus 40 C to 125 C |
Body, marking and reel data
| Body | PW, TSSOP 14 pin, 5.00 mm by 4.40 mm, with SOIC-14 and VSSOP-10 as the other family options |
| Reel | 2000 pieces on a large reel for the PWR string, carrier width 16.4 mm |
| Finish | NIPDAU, moisture level 2 at 260 C with a one year floor life |
| Marking | INA205A on the row, which names the gain in a way most of the family does not |
| Grade | Industrial only, minus 40 C to 125 C, no AEC-Q100 row in this document |
Two thresholds instead of one
A single current limit forces a choice between nuisance trips and slow protection. Two comparators allow both: the fast one catches a dead short and the delayed one catches a thermal overload, and the controller can tell the difference because they are separate open drain lines. That is worth four extra pins on a 14 pin body and it is the reason this family survived while simpler monitors moved to integrated digital parts.
The trade is accuracy and quiescent current. At 3.5 percent error and 1.8 mA, the part belongs in a mains powered chassis where a trip point within a few percent is enough and where the housekeeping rail has current to spare. The 16.4 mm carrier and the TSSOP body also mean the reel fits standard feeders, which sounds trivial until a line has to buy a new feeder for a 12 mm part. Where a project is consolidating several monitor variants, our vendor consolidation page sets out how the comparator count and the gain map onto one family, and the power management cross reference lists the alternatives by common mode window.
Buyer questions on the INA205AIPWR
What does the programmable delay on comparator two do? It holds the comparator from responding for a set time, so a short inrush spike does not trip the system while a sustained overload still does. The delay is set by an external capacitor.
Can the internal references be overridden? On the 14 pin bodies yes, both comparator references can be driven from outside. On the 10 pin VSSOP only the internal 0.6 V reference is available.
Is the 1.2 V reference output able to supply a load? It is a bias reference for dividers, not a rail. Anything drawing real current needs a buffer, and the output is only brought out on the 14 pin package.
Availability and ordering notes
The PWR string is active at 2000 pieces on a large reel with NIPDAU and moisture level 2, marking INA205A. The carrier table in the same document prints a 16.4 mm width against a SOIC row, which is a packaging table artefact and not a second body: the PWR suffix is the TSSOP 14. We confirm the body and the comparator configuration before quoting, because the 10 pin version loses the delay and the reference output, and the incoming inspection plan covers the marking check that catches a mixed carton. The 14 pin body is also the only one in the family that brings out both the delay capacitor and the reference output, so a customer who needs either of those is on this package by definition rather than by preference.