Contact Us

INA201AIDR

Brand: Texas Instruments
Texas Instruments INA201AIDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA201AIDR — Power Management & Signal Chain | Superb Automation

INA201AIDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA201AIDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA201AIDR: 50 V/V high side monitor with a comparator and its own reference

The INA201AIDR is the 50 V/V member of the INA200 to INA202 family, a high side current shunt monitor that carries an open drain comparator and a 0.6 V internal reference inside the same 8 pin package. The amplifier side reads a shunt sitting anywhere between 16 V below ground and 80 V above it, multiplies the drop by 50 and delivers a voltage output with 300 kHz of bandwidth. The comparator side compares the same signal against a threshold set by an external divider from the internal 0.6 V reference, and it can latch so that a transient trip stays visible to the controller until it is reset.

That combination is the reason the part exists. A separate amplifier plus comparator plus reference is three placements, three tolerance stacks and three lines on the test plan, and the INA201 folds them into one SOIC-8. Total error is 3.5 percent maximum over temperature, which is a trip threshold budget rather than a measurement budget, and the quiescent current is 1800 uA maximum, which is high enough that a battery product would switch it.

Key data for the INA201AIDR

Gain50 V/V, with 20 V/V as INA200 and 100 V/V as INA202 in the same body and pinout
InputCommon mode minus 16 V to plus 80 V, unidirectional, independent of the 2.7 V to 18 V supply
ComparatorOpen drain output, 0.6 V internal reference, external divider sets the trip point, latch held by the RESET pin
Accuracy3.5 percent maximum total error over temperature, including gain, offset and common mode terms
Bandwidth500 kHz at gain 20, 300 kHz at gain 50, 200 kHz at gain 100 with a 5 pF load
Supply2.7 V to 18 V, 1800 uA maximum quiescent current, single supply only

Body, marking and reel data

BodyD, SOIC 8 pin, 4.90 mm by 3.91 mm, with VSSOP-8 as the smaller option in the family
Reel2500 pieces on a large reel for the DR string, the only packing printed for this row
FinishNIPDAU, moisture level 2 at 260 C with a one year floor life
MarkingINA on the INA201 row, the same three characters the family table prints for the die
GradeMinus 40 C to 125 C, industrial rows only, no automotive qualified version in this document

Latch, reset and the trip point

A latching comparator solves a specific problem: a fault that lasts 200 us is invisible to a controller polling every millisecond, and the board reboots with no record of why. The latch holds the comparator output until the RESET pin is pulled low, so the first event is preserved. Grounding RESET or leaving it open makes the comparator transparent, which is what a hardware overcurrent shutdown wants because the trip should clear itself when the current falls back.

The trip point is set by two resistors from the 0.6 V reference and the shunt signal, and the tolerance of those resistors adds to the 3.5 percent of the amplifier. A production test that trims the divider is more accurate than one that relies on 1 percent resistors, and the divider is the first thing to check when a board trips early. Where a product is being moved from a discrete comparator arrangement, our power management cross reference lists the monitor families by integrated comparator count and reference, and the obsolete part cross reference hub carries the discontinued high side monitors with their nearest active equivalents.

Buyer questions on the INA201AIDR

Is the comparator input the same node as the amplifier output? No. The comparator has its own input path from the shunt signal, so the trip threshold is independent of the amplifier gain and of the ADC range. That is what allows a 50 V/V output and a separate current limit on one part.

Can the reference drive an external load? The 0.6 V reference is meant for a resistor divider. Drawing more than the specified current shifts the threshold, so a buffer is needed if anything else uses it.

What happens on a 48 V bus? The common mode ceiling is 80 V so the inputs are fine, but the supply stays at 18 V maximum. The device runs from the housekeeping rail, not from the bus.

Availability and ordering notes

The DR string is active at 2500 pieces on a large reel with NIPDAU and moisture level 2. There is no small reel row printed for this string, so a prototype quantity comes from a broken reel or a distributor cut. The family is industrial only, and the automotive current sense families are separate documents with their own order codes. We confirm the gain digit and the body before quoting, and the reel label, date code and moisture history are recorded in the sourcing audit trail.