INA197AIDBVR
Product Specifications
INA197AIDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA197AIDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA197AIDBVR: 50 V/V wide common mode monitor for 48 V rails
The INA197AIDBVR sits in the middle of the INA193 to INA198 family at 50 V/V, in the pin arrangement shared with the INA196 and INA198, in the SOT-23 5 pin body. It reads a shunt sitting between 16 V below ground and 80 V above it while running from a 2.7 V to 18 V housekeeping supply, and it delivers 50 times the shunt drop as a voltage the ADC can take directly. Bandwidth is 300 kHz with a 5 pF load, total output error is 3 percent maximum over temperature, and the quiescent current is 900 uA maximum.
Fifty is a useful gain when the shunt cannot be made large. A 48 V bus at 20 A with a 1 milliohm shunt develops 20 mV, which at gain 50 is 1 V at the output, comfortably inside a 3.3 V converter input and well above the offset floor of the part. The same 1 milliohm shunt at gain 20 gives 400 mV, still usable but closer to the error terms that dominate at low signal. That trade is the reason the family ships three gains rather than one: the gain is chosen so the full load signal lands in the top third of the output range.
Key data for the INA197AIDBVR
| Gain | 50 V/V, between the 20 V/V INA196 and the 100 V/V INA198 in the same pin order |
| Input | Common mode minus 16 V to plus 80 V, unidirectional, independent of the supply voltage |
| Accuracy | 3 percent total output error maximum over temperature, offset included in the figure rather than quoted alone |
| Bandwidth | 300 kHz with a 5 pF load, 500 kHz on the 20 V/V row and 200 kHz on the 100 V/V row |
| Supply | 2.7 V to 18 V, 900 uA maximum quiescent current, no enable pin |
| Output | Voltage output, 50 mV from the positive rail at light load, ground referred |
Body, marking and reel data
| Body | DBV, SOT-23 5 pin, 2.90 mm by 1.60 mm |
| Reel | 3000 pieces on a large reel for the R suffix, 250 pieces for the T suffix |
| Finish | NIPDAU, moisture level 2 at 260 C, one year floor life after the bag is opened |
| Marking | BJK on the INA197 row, three characters shared across the family table |
| Temperature | Minus 40 C to 125 C, specified over the full industrial range |
The middle gain, and when it is the wrong choice
Gain 50 is a compromise and compromises have a failure mode. On a rail where the load current varies over two decades the high end saturates before the low end is readable, and no single gain fixes that. The usual answer is to pick the gain for the top of the range and accept that the bottom is not measured, or to use a digital power monitor with a programmable range. The INA197 is the right part when the current of interest is within one decade and the bus is above 26 V, which describes a great many telecom and industrial supplies.
The second limit is thermal. A 1 milliohm shunt at 20 A dissipates 0.4 W, which is a real thermal decision on a small board and not a resistor choice made at the last minute. Our power management cross reference lists the monitor families by gain and common mode window, and the pin to pin cross reference shows which of them can share a land pattern when a customer wants to offer two current ranges from one board.
Buyer questions on the INA197AIDBVR
How do I choose between gain 20, 50 and 100? Pick the gain that puts the maximum load current at about two thirds of the output swing at your supply voltage. Higher gain buys resolution and costs headroom, and the error figures get worse as the signal falls.
Does the part need a separate reference? No. The output is ground referred and unidirectional, so a single shunt drop direction is all it can read. Bidirectional sensing needs a different family with a reference pin.
Is 300 kHz enough for a current loop? For most supplies yes, because the loop crossover sits well below it. For a fast overcurrent trip the 20 V/V row at 500 kHz is the better starting point.
Availability and ordering notes
The R suffix ships 3000 pieces on a large reel and the T suffix 250 on a small reel, both active with moisture level 2 and a one year floor life. The same die is offered in the other pin order as the INA194, which is the substitution that a depot most often attempts and most often gets wrong. We quote the exact suffix and record the pin order on the sourcing audit trail so a repeat order cannot silently change variant.