Contact Us

INA196AIDBVR

Brand: Texas Instruments
Texas Instruments INA196AIDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA196AIDBVR — Power Management & Signal Chain | Superb Automation

INA196AIDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA196AIDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA196AIDBVR: 20 V/V current shunt monitor with a minus 16 V to plus 80 V common mode window in the five pin SOT-23

INA196AIDBVR is a voltage output current shunt monitor from the INA19x family, the 20 V/V member on the INA196 pin arrangement in a SOT-23 body of 5 pins. It senses across a shunt at common mode from minus 16 V to plus 80 V independently of its supply, runs from 2.7 V to 18 V, draws 700 uA typical and 900 uA maximum, and holds a plus or minus 2 mV offset with a plus or minus 1 per cent gain error. The bandwidth reaches 500 kHz and the total output error is specified at 3 per cent maximum over temperature, which places the part in welding, telecom and motor supplies rather than in precision metering.

Order code and package

INA196AIDBVRSOT-23 DBV body, 5 pins, 3000 pieces on a large reel, Active in the addendum dated 11 November 2025, NIPDAU finish, moisture level 2 with a one year floor life, marking BJE, minus 40 to plus 125 degrees
INA196AIDBVTthe same DBV body on a 250 piece small reel at the same moisture level and marking, which is the prototype quantity
INA196AIDBVR1G4the G4 row of the same body and the same 3000 piece reel, printed separately with its own finish column, which is the row a material declaration usually asks for
INA193AIDBVRthe same 20 V/V transfer function on the INA193 pin arrangement, marking BJJ, which is the alternative when the board was drawn for the other pinout
INA197AIDBVRthe 50 V/V member on the INA196 pin arrangement, marking BJH, which is the sibling that keeps the same footprint when a larger shunt signal is wanted

Electrical parameters that decide the application

Common mode rangeminus 16 V to plus 80 V, independent of the supply, which covers a 48 V telecom bus and the negative excursion of a motor phase
Supply2.7 V to 18 V single rail, 700 uA typical and 900 uA maximum quiescent current
Offset voltageplus or minus 2 mV maximum referred to the input, with 0.5 mV typical, which is a millivolt class part rather than a microvolt class one
Offset drift2.5 uV per degree typical, quoted in the drift row of the electrical table
Gain20 V/V on the INA196 member, against 50 V/V on INA197 and 100 V/V on INA198, in the same five pin body
Gain errorplus or minus 1 per cent maximum and 0.2 per cent typical, both measured with a sense voltage between 20 mV and 100 mV
Total output error3 per cent maximum over temperature, which is the figure that includes offset, gain error and drift together
Common mode rejection80 dB minimum and 94 dB typical across the full window, rising to 100 dB minimum and 120 dB typical between 12 V and 80 V
Bandwidthup to 500 kHz on the faster members, with the INA194 row printed at 300 kHz into a 5 pF load
Input bias current8 uA typical on the inverting input, which has to be counted against the shunt voltage at high shunt values
Outputvoltage output into a converter or a comparator, with the transfer function set by the fixed gain and no external divider
Temperatureminus 40 to plus 125 degrees on every member of the family and every reel size

Family variants and how they differ

Pin arrangementthe INA193 to INA195 and the INA196 to INA198 are the same three transfer functions on two pin arrangements, so a 20 V/V part exists in both and the two are not interchangeable on a populated board
INA196 against INA180the INA180 has 26 V of common mode and 84 dB of rejection with a 150 uV offset, while this part reaches 80 V with a 2 mV offset, so the window and the precision move in opposite directions
INA196 against INA296Athe INA296A reaches 110 V with a 10 uV offset and 1.1 MHz, which is a different class of part at a different price, and the 2 mV offset here is what that price buys
INA196 against INA186the INA186 is a 40 V zero drift part at 48 uA, so a battery instrument wants the INA186 and an 80 V industrial bus wants this part
Body optionsthe five pin DBV body is the only one in this family, so the reel size is the only packaging decision

Points to check before this part goes on a BOM

The offset is 2 mV, not 2 uV, and that single fact sets the smallest usable sense voltage. On a 20 V/V gain the 2 mV offset appears as 40 mV at the output, and a converter with a 3.3 V range sees that as 1.2 per cent of full scale before any other error. A 100 mV full scale sense signal is therefore the practical floor, and a circuit that needs to resolve 10 mV of sense has to use a zero drift part instead.

The total error figure of 3 per cent over temperature is the number to use for a go or no go decision, because the offset, the gain error and their drifts add in a way the individual rows do not show. At a 100 mV sense signal the 2 mV offset is 2 per cent on its own and it doubles at a 50 mV signal, so a specification that needs 2 per cent across the range cannot be met by this family at all.

The 80 dB common mode rejection at low common mode rises to 100 dB between 12 V and 80 V, which is unusual and useful: the part is better at high bus voltages than near ground. The reason is the input divider ratio, which is set for the high side, and the practical consequence is that a 48 V measurement carries less common mode error than a 5 V one on the same part.

The 500 kHz bandwidth is the reason this family appears in welding equipment and motor drives, where the current has to be followed rather than averaged. The output settles fast enough for a control loop that closes at tens of kilohertz, and the 20 V/V gain keeps the output inside a 3.3 V range for a 150 mV sense signal. A part chosen for bandwidth and a part chosen for offset are rarely the same part, and this is the bandwidth one.

The two pin arrangements are electrically identical and mechanically different. A buyer who substitutes INA193 for INA196 because both are 20 V/V has swapped the supply and the output pins, and the board will not work. The vendor prints the note in the device comparison table precisely because this substitution gets attempted, and the catalogue entry has to be matched to the arrangement on the board rather than to the gain.

The 700 uA of quiescent current is an order of magnitude above the low power monitors and it is the cost of the 500 kHz bandwidth. On a mains powered welding set it is invisible; on a battery instrument it is the whole budget. The family is therefore a mains powered part, and a battery powered product that inherits it has to re-examine the current budget rather than only the footprint.

Working the sense voltage from the offset

With a 2 mV offset and a 1 per cent gain error, the error is 2 mV plus 1 per cent of the reading. At a 200 mV sense signal that is 2 mV plus 2 mV, so 2 per cent in total. At a 50 mV signal it is 2 mV plus 0.5 mV, which is 5 per cent. The crossover where the two terms are equal sits at 200 mV, and everything below it belongs to the offset.

That arithmetic decides the shunt, not the amplifier. A 10 A full scale current with a 200 mV sense signal needs a 20 milliohm shunt, which at 10 A dissipates 2 W. A 2 milliohm shunt gives 20 mV at 10 A and 0.2 W, but then the offset dominates at 10 per cent error. The thermal budget and the error budget pull in opposite directions and the 3 per cent total error figure is the line between them.

Protecting the inputs on an inductive load

The inputs survive the common mode window, not an indefinite overcurrent. On a welding set or a motor drive the shunt sees the full fault current and the amplifier sees the resulting common mode step; a pair of Schottky diodes from each input to the supply rails and a small series resistor is the standard protection, at the cost of a bias current path through the diodes. The 80 V window leaves room for a 48 V bus with 32 V of transient, which is more than most 48 V systems produce.

Where this order code fits

Welding equipment, notebook computers, cell phones, telecom equipment, automotive supplies, power management and battery chargers are the applications the vendor names, and the common thread is a bus that is far above the logic supply and a current that has to be followed rather than merely logged. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can I substitute INA193AIDBVR for INA196AIDBVR? No. The two carry the same 20 V/V gain on different pin arrangements, so the supply and output pins differ.

What is the smallest sense voltage this part resolves? Around 100 mV, because the 2 mV offset is 2 per cent of a 100 mV signal and grows quickly below it.

Does it measure a negative current? The common mode window reaches minus 16 V, so a shunt below ground is inside the window, but the transfer function is single ended and a bidirectional reading needs a reference offset.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.