Contact Us

INA180B4IDBVR

Brand: Texas Instruments
Texas Instruments INA180B4IDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA180B4IDBVR — Power Management & Signal Chain | Superb Automation

INA180B4IDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA180B4IDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA180B4IDBVR: gain of 200 in the second pinout of the INA180 family

The INA180B4 is the gain of 200 V/V member of the INA180 family with the B pinout. The electrical behaviour matches the A4 member: common mode from minus 0.2 V to 26 V, a 2.7 V to 5.5 V supply, a rail to rail output and a bandwidth of 105 kHz at this gain. What changes is the order of the pins, and that is not a cosmetic difference. On a five pin body the sense pair, the supply, ground and the output have to fit around a shunt that already exists on the board, and the second pinout lets the output face the converter or lets the supply pin reach a decoupling capacitor without a via. A part ordered by gain alone and soldered by pin number gets the supply and the output swapped.

Gain of 200 suits a small shunt: a 10 milliohm resistor carrying 5 A develops 50 mV, which becomes 10 V at the output, so the full scale reading lands at a level a 12 bit converter can use without an extra stage. Offset at this gain is multiplied by 200 as well, which is why the family's 150 microvolt figure at zero common mode becomes 30 mV of output error and why the offset at 12 V of common mode, 500 microvolts, has to be part of the error budget at the top of the range.

Key data for the INA180B4IDBVR

Gain200 V/V fixed, the highest gain in the family, so a 10 milliohm shunt at 5 A gives 10 V of output
PinoutB pinout, different pin order from the A devices in the same body, so the two are not interchangeable on a board
Common modeMinus 0.2 V to 26 V, independent of supply, with the negative end sized for switch node ringing
Bandwidth105 kHz at a gain of 200, with a 2 V per microsecond slew rate, the slowest member of the family
Offset150 microvolts maximum at zero common mode, 500 microvolts maximum at 12 V, multiplied by 200 at the output
Supply2.7 V to 5.5 V, 260 microamps maximum quiescent current, rail to rail output

Body, marking and reel data

BodyDBV, SOT-23 5 pin, 3000 pieces on a large reel, 250 piece small reel on the T suffix
MarkingA four character code on the top of the package that encodes both the gain and the pinout
FinishNIPDAU or SN depending on the row, moisture level 1 with unlimited floor life
GradeAmbient minus 40 C to 125 C, industrial rows, with the Q1 automotive string in a separate document

Why two pinouts exist in one family

Current sense amplifiers are placed by the shunt, not by the converter. The shunt sits where the current already flows, often on the edge of a power stage, and the amplifier has to reach it with two short traces while its output travels to an ADC that may be on the other side of the board. A single pinout forces one of those two connections to cross, and on a two layer board that crossing is a cut in the ground plane under the shunt. The second pinout exists so the same die can be placed either way, and the family table in the data sheet lists both so the two are not confused at the ordering stage.

Where a customer's approved part is the A4 and the A4 is short, the B4 is the same gain in the other pinout and cannot be substituted without a board change. That distinction is exactly what our drop in verification note records, and the pin to pin cross reference page lists which bodies share a pinout and which only share a function.

Buyer questions on the INA180B4IDBVR

Is the B4 the same as the A4? Same gain and same electrical specification, different pin order. The data sheet device comparison table lists both columns and the note that A devices use pinout A and B devices pinout B.

Why does gain 200 limit the bandwidth to 105 kHz? The family is a fixed gain block, so bandwidth falls as gain rises: 350 kHz at a gain of 20 down to 105 kHz at 200. A current loop that needs more speed uses a lower gain and a larger shunt.

Does the offset really multiply by 200? Yes, input offset appears at the output multiplied by the gain. That is why the 12 V common mode figure of 500 microvolts is the one to use in an error budget at the top of the range, not the zero volt figure.

Availability and ordering notes

The 3000 piece reel and the 250 piece small reel are both active, with moisture level 1 on most rows so no bake is needed. Because the marking encodes the pinout, a mixed reel is caught at goods inward by reading the top of the package rather than the label. We quote the full string including the B prefix, and where a customer's board was written for the A pinout we say so before shipping rather than after, which is the point of the OEM procurement review we run on every first order.