INA180A3QDBVRQ1
Product Specifications
INA180A3QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA180A3QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA180A3QDBVRQ1: a gain of 100 current sense amplifier qualified for a vehicle
The INA180-Q1 senses the drop across a shunt at common mode voltages from minus 0.2 V to 26 V while running from a 2.7 V to 5.5 V supply, and the A3 member of the family has a fixed gain of 100 V/V. The negative end of the common mode range is the part that matters in a motor circuit, because the switch node of a half bridge rings below ground on every commutation and a monitor that cannot follow it loses the reading at exactly the moment a fault appears. Offset is 150 microvolts maximum at zero common mode and 500 microvolts maximum at 12 V, gain error is 1 per cent maximum over temperature, and quiescent current is 260 microamps maximum.
This is the automotive string: AEC-Q100 qualified, temperature grade 1 covering minus 40 C to 125 C ambient, HBM level 2 and CDM level C6. The five pin SOT-23 body is packed 3000 pieces on a large reel with the marking 1MP3, and the same die is offered in a second pinout under the B prefix for boards where the routing of the sense pins is easier the other way round. Bandwidth at a gain of 100 is 150 kHz, which is fast enough to catch a stall current in a small actuator and slow enough that switching noise averages out.
Key data for the INA180A3QDBVRQ1
| Gain | 100 V/V fixed by a trimmed resistor network on the die, A3 member of the family |
| Common mode | Minus 0.2 V to 26 V, independent of the supply, so a ringing switch node stays inside the window |
| Offset | 150 microvolts maximum at zero common mode, 500 microvolts maximum at 12 V of common mode |
| Accuracy | Gain error 1 per cent maximum over minus 40 C to 125 C, drift 1 microvolt per degree maximum |
| Bandwidth | 150 kHz at a gain of 100, with a 2 V per microsecond slew rate on the output |
| Supply | 2.7 V to 5.5 V, 260 microamps maximum quiescent current, rail to rail output swing |
Body, marking and reel data
| Body | DBV, SOT-23 5 pin, 3000 pieces on a large reel, 180 mm carrier |
| Marking | 1MP3 on the A3 automotive row, which identifies the gain and the qualification on the reel |
| Finish | NIPDAU, moisture level 1 with unlimited floor life, no bake needed after the bag is opened |
| Grade | AEC-Q100 temperature grade 1, minus 40 C to 125 C ambient, HBM level 2 and CDM level C6 |
Where the automotive grade changes the decision
The industrial member of this family has the same transfer function and the same pinout, so an engineer can prove a circuit with the cheaper part and move to the Q1 string for production. What changes is the qualification record: AEC-Q100 grade 1, the ESD classification and the functional safety documentation, all of which a tier one supplier asks for before a part goes on a vehicle platform. The package marking also changes, so a goods inward check that reads the marking rather than the label catches a mixed reel before it reaches the line.
Typical uses are motor control, battery monitoring, lighting and overcurrent detection in body and powertrain modules. The 26 V common mode covers a 12 V system with load dump margin when the sense point is protected, and the 150 kHz bandwidth suits a current loop that closes at a few kilohertz. Where a customer is moving a board into an automotive programme, our supplier quality audit page sets out what we check before shipping a Q1 part, and the power management cross reference lists the gain options across the family.
Buyer questions on the INA180A3QDBVRQ1
Is the Q1 part drop in for the industrial INA180A3? Electrically yes, same pinout and same gain. The qualification, the marking and the documentation differ, and a customer's approved vendor list usually names the Q1 string for automotive work.
Why is the offset different at 12 V of common mode? The input stage is a difference pair, and its offset moves with the common mode voltage. The vendor specifies both ends, 150 microvolts at zero and 500 microvolts at 12 V, rather than quoting a single figure.
Can it measure a negative current? It measures the voltage across the shunt in one direction only. The minus 0.2 V at the low end of the common mode range is there to survive ringing, not to allow bidirectional sensing.
Availability and ordering notes
The 3000 piece reel is the published packing and moisture level 1 means the reel can sit on an open line without a floor life clock, which matters on a mixed model line. We ship the Q1 string against the printed orderable code and keep the qualification documents with the lot, and where a build needs a partial reel the split is recorded so the traceability chain stays intact through the sourcing audit trail.