Contact Us

INA139QPWRQ1

Brand: Texas Instruments
Texas Instruments INA139QPWRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA139QPWRQ1 — Power Management & Signal Chain | Superb Automation

INA139QPWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA139QPWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA139QPWRQ1: an automotive high side shunt monitor that outputs a current

The INA139-Q1 senses the drop across a shunt resistor on the high side of a load and converts it into an output current rather than a voltage. That choice is what makes the part useful in a vehicle harness: the current travels down a wire to a remote measuring point without losing amplitude to a divider, and a single load resistor at the far end sets the full scale voltage. The common mode range is 2.7 V to 40 V for this member and 2.7 V to 60 V for the INA169-Q1 sibling, so the same circuit works on a 12 V rail, a 24 V rail and the load dump region that automotive testing insists on. Full scale sense voltage is 100 mV on the INA139 family, which keeps shunt loss low at tens of amps.

Transconductance is 1000 microamps per volt with a 980 to 1020 window over temperature, so a 100 mV full scale drop produces 100 microamps and a 5 kilohm load resistor turns that into 500 mV. Common mode rejection is 100 dB minimum, which is the number that decides whether a 10 mV shunt signal survives a 40 V common mode with the switching noise of an alternator on top of it. The part is qualified to AEC-Q100 and marked Q1, and it is specified over the automotive temperature range in the PW body.

Key data for the INA139QPWRQ1

Common mode2.7 V to 40 V on the INA139-Q1, 2.7 V to 60 V on the INA169-Q1 in the same document
Full scale100 mV sense drop on the INA139-Q1, 500 mV on the INA169-Q1, both set by an external load resistor
Transfer1000 microamps per volt typical, 980 to 1020 over temperature, so 100 mV gives 100 microamps
RejectionCommon mode rejection 100 dB minimum and 115 dB typical at 50 mV of sense voltage
OffsetOffset drift 1 microvolt per degree typical, 10 maximum, supply rejection 0.5 to 10 microvolts per volt
OutputCurrent output with 1 megohm in parallel with 5 pF of output impedance, so the load sets the gain

Body, marking and reel data

BodyPW, TSSOP 8 pin, 1.2 mm maximum height, 2000 pieces on a large reel of 353 mm
GradeAEC-Q100 qualified, Q1 suffix, automotive temperature range printed on the addendum row
SiblingsINA169-Q1 in the same PW body, and the industrial INA139 and INA168 in SOT-23 and SOIC
Packing2000 piece reel is the only published packing for the Q1 string in this body

Where a current output monitor wins

A voltage output monitor sits next to the shunt and sends a voltage to the controller, which is fine when the controller is on the same board. In a vehicle the shunt is often in a fuse box or a battery distribution module and the ADC is a metre away, and a voltage sent down that wire picks up the same noise the harness was going to pick up anyway. A current output is immune to series resistance in the wire and to ground offsets, because the receiver converts current to voltage at the point of measurement. That is also why the load resistor tolerance becomes the accuracy limit rather than the amplifier.

The other advantage is filtering. A capacitor across the load resistor sets a single pole low pass response without touching the sense lines, so the monitor can be made slow enough to ignore motor commutation while still catching a short circuit. Where a customer is moving a shunt monitor into an automotive build, our automotive grade component page covers the qualification routes, and the power management cross reference lists the current output monitors by common mode range.

Buyer questions on the INA139QPWRQ1

What load resistor gives a 5 V full scale output? At 100 mV of sense voltage the output current is 100 microamps, so 5 V needs 50 kilohm. That value also sets the bandwidth, which falls as the resistor rises, so the settling requirement decides the compromise.

Does the part measure current in both directions? No. It is a unidirectional high side monitor and the output is zero at zero current. A bidirectional measurement needs a reference offset or a different family member.

Is the Q1 string the same silicon as the industrial part? The electrical function is the same and the qualification is not. The Q1 rows carry AEC-Q100 qualification and the automotive temperature range, and the addendum prints the PW body at 2000 pieces on one reel size.

Availability and ordering notes

Automotive parts are bought against a qualification record as much as against a part number, so the Q1 string has to be ordered as printed rather than substituted with the industrial body. The 2000 piece reel is the published packing, and a smaller build is served from a broken reel or from a distributor's cut tape, which changes the trace ability of the delivery. We hold the traceability documents with the shipment and can supply the sourcing audit trail for each lot.