Contact Us

INA129PA

Brand: Texas Instruments
Texas Instruments INA129PA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA129PA — Power Management & Signal Chain | Superb Automation

INA129PA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA129PA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA129PA: the A grade eight pin plastic DIP

The INA129PA is the A grade of the eight pin plastic DIP in a 50 piece tube: the same 49.4 kΩ gain network as the plain P code, with the tighter offset and gain error bin. It is the code for a bench or calibration fixture built around the 49.4 kΩ equation where the offset has to be inside a window the plain grade would exceed, and it takes a socket without a footprint change from the plain part.

The family rows are unchanged across the grades: 0.5 µV per degree of drift, 5 nA of bias current, 8 nV per root hertz of noise, 120 dB of common mode rejection, 700 µA of quiescent current, 1.3 MHz at unity gain and 200 kHz at a gain of 100, on a supply from plus or minus 2.25 V to plus or minus 18 V. The three op amp current feedback stage is what holds the bandwidth at a high gain and is the property that separates this family from an op amp pair.

The INA129PA rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, current feedback
Vendor statusActive, production
Data sheetSBOS051G, revised January 2026
GradeA suffix, tighter offset and gain error window
Gain equationG = 1 + 49.4 kΩ divided by RG
Input offset voltageFamily row 50 µV maximum, tighter on the A bin
Offset drift0.5 µV per degree maximum, both grades
Input bias current5 nA maximum
Voltage noise8 nV per root hertz at 1 kHz
Common mode rejection120 dB minimum
Bandwidth1.3 MHz at a gain of 1, 200 kHz at a gain of 100
Input protectionPlus or minus 40 V without damage
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current700 µA typical
BodyPDIP, P outline, 8 pins
Carrier50 pieces per tube
Lead finishPublished as call TI on the P rows
SOIC siblingINA129UA with the same die and grade

Why the INA129 uses 49.4 kΩ and the INA128 uses 50 kΩ

The two parts in this document are the same silicon with one difference in the internal gain network: the INA128 uses 50 kΩ so that G = 1 + 50 kΩ divided by RG, and the INA129 uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG. The 49.4 kΩ is there so that a resistor value chosen for a competing part gives the same gain in the INA129, which is what makes it a drop-in replacement on an existing board without a resistor change. On a gain of 100 the difference between the two equations is 1.2 per cent, which is larger than the resistor tolerance and large enough to fail a calibrated channel.

Because of that, INA129PA must be bought as the part the board was drawn for, and the substitution question is not symmetrical. An INA129 in an INA128 socket runs 1.2 per cent low at a gain of 100 and 0.12 per cent low at a gain of 10, so it passes a functional test and fails a calibration. An INA128 in an INA129 socket runs high by the same amount. Neither failure is visible without a gain measurement, which is why the two codes should never be treated as interchangeable.

50 µV of offset and half a microvolt per degree

The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA129PA can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.

The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.

Current feedback input stage and bandwidth at a gain of 100

The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA129PA serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.

Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.

The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm

The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.

The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA129PA the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.

The REF pin, the 8 Ω rule and single supply references

The REF pin sets the output level and is part of the signal path in a way that is easy to forget. Any resistance in series with it appears as a common mode error at the input and as a gain error at the output at the same time, and the vendor states that 8 Ω is enough to degrade common mode rejection on a typical part. A divider made of two 10 kΩ resistors has a source impedance of 5 kΩ, which is three orders of magnitude above that, so an unbuffered divider is not a reference for INA129PA at any gain.

On a bipolar supply the REF pin goes to ground, and ground has to be the same ground the converter uses or the difference appears as an offset. On a single supply the pin goes to a buffered mid rail, and the buffer has to be able to sink and source the current the REF pin draws, which is small but not zero. A shunt reference with a 1 µF capacitor is the cheap answer; an op amp buffer is the answer when the reference also has to drive other channels. Both are one more part than a divider and both are the reason a single supply channel measures what it claims.

Gain error rows, the A grade and the 0.024 per cent window

Gain error on this family is quoted per gain setting and per grade, and the tightest row is 0.024 per cent at a gain of 1 on the A grade parts. That figure is smaller than the tolerance of the resistor that sets the gain, so the resistor, not the amplifier, is what a calibration adjusts. At a gain of 100 the family rows widen and the A grade still holds a window about half as wide as the plain grade, which is the practical difference between the two bins on a channel that is calibrated once rather than per unit.

Nonlinearity is 0.001 per cent of full scale on the plain grade and 0.0005 per cent on the A grade, which is well below any converter this part is likely to drive. The number that limits a real channel is the gain drift, quoted in ppm per degree, because it cannot be trimmed at the bench and it moves with the cabinet temperature. On INA129PA the drift row is the one to put in a specification that has to hold over temperature, and the room temperature gain error row is the one to put in a production test limit.

Buying INA129PA

The grade is the decision and the package is the constraint. A DIP is bought when the part has to be socketed, and once it is socketed the lead finish matters as much as the grade: the P rows are published as call TI, so a gold finish and a tin finish both appear in the channel, and a socketed part that is inserted repeatedly needs the gold. Asking for the finish on the order is the only control that works.

The grade is not visible on the body without the label, so the receiving record is the only evidence of what was shipped. On a calibration fixture that is acceptable; on a production board it is the reason to move to the SOIC code where the reel label carries the full string. Our supplier quality audit page covers how the label and the finish are checked, and the drop in replacement verification page covers a grade change.

Questions that arrive with this part number

Whether the A grade is worth it is the first question, and on a small full scale channel the tighter bin can remove a trim, which is usually worth more than the premium. The second is whether the 49.4 kΩ equation can be replaced by the 50 kΩ one, and it can if the gain resistor values are recalculated and the channels recalibrated, which is a drawing change rather than a substitution.

The third is about the socket contact resistance in series with the gain resistor. At a gain of 1000 the resistor is about 50 Ω on this equation too, so an ohm of contact resistance is 2 per cent of gain error, and the fixture should be calibrated in its socket rather than on a bare board.