Contact Us

INA128U-2K5

Brand: Texas Instruments
Texas Instruments INA128U-2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA128U-2K5 — Power Management & Signal Chain | Superb Automation

INA128U-2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA128U-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA128U-2K5: the hyphenated spelling of the plain reel code

This entry writes the plain reel code with a hyphen, INA128U-2K5, which the catalogue carries next to the vendor form with a slash. The part is the plain grade SOIC body on a large reel, and the page exists so that either spelling lands on the same specification rather than on a page that looks like a different device. On a family where the reel rows also carry a different moisture level, the spelling is the least important of the three things a buyer has to get right.

The device is a three op amp instrumentation amplifier with a current feedback input stage: 50 µV of maximum offset, 0.5 µV per degree of drift, 5 nA of bias current, 700 µA of quiescent current and a gain range from 1 to 10,000 with one resistor. On a plus or minus 15 V supply the common mode range is wide enough for a bridge sitting at mid rail, and the 120 dB rejection holds it there against a 50 Hz disturbance.

The INA128U-2K5 rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, current feedback
Vendor statusActive, production
Data sheetSBOS051G, revised January 2026
Vendor stringPrinted as INA128U/2K5 with a slash
Catalogue stringAlso indexed with a hyphen and without a separator
Gain equationG = 1 + 50 kΩ divided by RG
Input offset voltage50 µV maximum
Offset drift0.5 µV per degree maximum
Input bias current5 nA maximum on the standard rows
Common mode rejection120 dB minimum
Bandwidth1.3 MHz at a gain of 1, 200 kHz at a gain of 100
Input protectionPlus or minus 40 V without damage
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current700 µA typical
BodySOIC, D outline, 8 pins
CarrierLarge reel, quantity per the addendum row
Moisture levelLevel 3, 260 degrees, 168 hour floor life
A grade siblingINA128UA/2K5 with the tighter offset bin

Why the INA129 uses 49.4 kΩ and the INA128 uses 50 kΩ

The two parts in this document are the same silicon with one difference in the internal gain network: the INA128 uses 50 kΩ so that G = 1 + 50 kΩ divided by RG, and the INA129 uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG. The 49.4 kΩ is there so that a resistor value chosen for a competing part gives the same gain in the INA129, which is what makes it a drop-in replacement on an existing board without a resistor change. On a gain of 100 the difference between the two equations is 1.2 per cent, which is larger than the resistor tolerance and large enough to fail a calibrated channel.

Because of that, INA128U-2K5 must be bought as the part the board was drawn for, and the substitution question is not symmetrical. An INA129 in an INA128 socket runs 1.2 per cent low at a gain of 100 and 0.12 per cent low at a gain of 10, so it passes a functional test and fails a calibration. An INA128 in an INA129 socket runs high by the same amount. Neither failure is visible without a gain measurement, which is why the two codes should never be treated as interchangeable.

50 µV of offset and half a microvolt per degree

The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA128U-2K5 can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.

The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.

Tubes, reels and two different moisture levels

The SOIC rows ship 75 pieces in a tube or 2500 pieces on a large reel, and the DIP rows ship 50 pieces in a tube. The carrier decides the handling, not the part: a 75 piece tube is a prototype or a small build, and a 2500 piece reel is a production run that will take months to consume. Between those two there is nothing on the addendum, which is why a build of 500 boards is usually bought as several tubes and hand fed rather than as a partial reel.

The moisture level differs between the carriers on this family. The tube rows are published at level 2 with a one year floor life, and the reel rows at level 3 with a 168 hour floor life, so the same die has a different shop floor rule depending on how it arrived. A level 3 reel that is opened for a partial build has to go back into dry storage or be baked, and a 2500 piece reel can easily sit open across two builds. Reading the level off the label rather than off the part number is the practical control, and INA128U-2K5 is the code to check it against.

700 µA of quiescent current across a plus or minus 2.25 V to 18 V window

INA128U-2K5 draws 700 µA typical, which is four times the current of the micropower INA126 and a twentieth of what a fully featured instrumentation amplifier usually costs. The supply window of plus or minus 2.25 V to plus or minus 18 V covers a plus or minus 15 V industrial rack and a plus or minus 2.5 V single cell analogue front end in the same part number, and the common mode range tracks the rails rather than sitting at a fixed offset from ground.

The current is flat with load and nearly flat with temperature, so the supply budget can be set from the data sheet row rather than measured. What is not in the row is the reference divider and the load current. A plus or minus 15 V part driving a 10 kΩ load at 10 V adds a milliamp, which is more than the amplifier, and a single supply channel with an unbuffered mid rail divider can add a quarter of a milliamp. The amplifier is therefore rarely the largest item in the budget, and the budget is still small enough that a battery instrument can afford two channels.

The REF pin, the 8 Ω rule and single supply references

The REF pin sets the output level and is part of the signal path in a way that is easy to forget. Any resistance in series with it appears as a common mode error at the input and as a gain error at the output at the same time, and the vendor states that 8 Ω is enough to degrade common mode rejection on a typical part. A divider made of two 10 kΩ resistors has a source impedance of 5 kΩ, which is three orders of magnitude above that, so an unbuffered divider is not a reference for INA128U-2K5 at any gain.

On a bipolar supply the REF pin goes to ground, and ground has to be the same ground the converter uses or the difference appears as an offset. On a single supply the pin goes to a buffered mid rail, and the buffer has to be able to sink and source the current the REF pin draws, which is small but not zero. A shunt reference with a 1 µF capacitor is the cheap answer; an op amp buffer is the answer when the reference also has to drive other channels. Both are one more part than a divider and both are the reason a single supply channel measures what it claims.

Settling time against gain on a multiplexed front end

The settling time curve on this family is the one to read before a channel is put behind a multiplexer. At a gain of 100 the part settles to 0.01 per cent in a few microseconds, which allows a scan rate in the tens of kilohertz; at a gain of 1000 the same figure stretches out and the scan rate falls with it. The stage before the converter has to settle from the previous channel's value, not from zero, so the worst case is a full scale step between two adjacent channels, and that is the step the vendor curve uses.

The other half of the settling budget is the multiplexer and the filter between it and the amplifier. A 1 kΩ series resistor with a 100 nF capacitor has a 100 µs time constant, which dominates the amplifier completely and is the usual reason a scan runs slower than the data sheet suggests. On INA128U-2K5 the settling figure is only useful when the input network in front of it is faster than the amplifier, and a channel that ignores that rule will show an inter-channel error that moves with the source impedance.

Buying INA128U-2K5

Write the vendor string on the purchase order and ask for the confirmation back in the same form, then check the reel label against it. A separator mismatch is harmless; a grade mismatch is not, because the A and plain bins share the die and the footprint and differ only in the offset window. The quantity is the third thing to check, and on a large reel it is printed on the label rather than implied by the suffix.

The reel is a production carrier, so the buying question is really a storage question. A level 3 reel that is opened and left out does not fail immediately; it fails at reflow with popcorning, which is a board level failure that gets blamed on the assembly process. Our incoming inspection plan covers the label and seal checks at the door, and the supplier quality audit page covers how the packaging is verified at the source.

Questions that arrive with this part number

Whether the hyphen and the slash forms are the same part is the first question and they are, with the vendor printing the slash. The second is whether the A grade can replace the plain grade on a shortage, and it can, because a tighter bin meets a wider specification; the reverse substitution is the one that needs a measurement.

The third is about the supply floor. Plus or minus 2.25 V is the minimum, which rules out a single 3.3 V rail, and a single supply channel needs a buffered mid rail and a signal that stays inside the common mode window. The part is not rail to rail at the input or at the output, and a channel that assumes otherwise will clip about three quarters of a volt before the rail.