Contact Us

INA105KP

Brand: Texas Instruments
Texas Instruments INA105KP is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA105KP — Power Management & Signal Chain | Superb Automation

INA105KP

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA105KP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA105KP: a unity gain difference amplifier that survives 20 V of common mode

The INA105 is a monolithic difference amplifier built from an operational amplifier and four laser trimmed resistors, wired for unity gain. It takes a differential input of up to plus or minus 10 V while the common mode voltage on the inputs sits anywhere between minus 20 V and plus 20 V, which is the range a current shunt on a split supply needs. Because the resistors are trimmed on the die, the common mode rejection reaches 86 dB minimum on the KP grade and 100 dB typical, without a resistor network that drifts with temperature. The same topology gives a fixed gain of 1 with no external parts, so the output is simply the difference of the two inputs plus the reference pin offset.

The KP suffix is the PDIP 8 pin body in a tube of 50 pieces. That body is still the practical choice for test fixtures, repair lines and instrument front ends that are built in tens rather than thousands, and it is the body the bench engineer can socket while a circuit is being proven. The SOIC version of the same silicon is the KU suffix, and its 2500 piece reel covers volume. Offset is 50 microvolts typical and 500 microvolts maximum on the KP grade, with a drift of 5 microvolts per degree typical, which is the number that decides whether a 10 mV shunt drop stays readable across a cabinet temperature swing.

Key data for the INA105KP

GainFixed unity gain, four trimmed resistors on the die, no external network, gain error 0.01 per cent typical
Common modePlus or minus 20 V on the inputs, differential input up to plus or minus 10 V
Offset50 microvolts typical and 500 microvolts maximum on the KP grade, 250 microvolts on the AM grade
Drift5 microvolts per degree typical and 10 maximum on the KP grade, referred to the output
RejectionCommon mode 86 dB minimum on the KP grade, 100 dB typical, supply rejection 1 microvolt per volt typical
Impedance50 kilohm differential and 50 kilohm common mode, which sets the loading on the source

Body, marking and reel data

BodyP, PDIP 8 pin, 50 pieces per tube, lead finish NIPDAU, no moisture floor life limit in a through hole body
SiblingD, SOIC 8 pin, INA105KU/2K5 at 2500 pieces on a large reel, active in the current addendum
RetiredThe bare INA105KU tube row is marked obsolete, the reel row of the same body is not
GradeAmbient minus 40 C to 85 C on every active row, no automotive grade in this family

Where a unity gain block still beats an op amp and four resistors

The obvious alternative is an operational amplifier with a four resistor difference network, and it is cheaper until the resistor tolerance and the matching are counted. A 0.1 per cent network gives about 66 dB of rejection before any trimming, and the ratio drift between the four resistors adds a term that no offset trim removes. The INA105 reaches 86 dB minimum with the network on the die, and the four resistors track because they sit next to each other on the same piece of silicon. For a 4 to 20 mA receiver across a 100 ohm shunt, that difference is the space between a reading that holds at 0.1 per cent and one that walks as the cabinet warms.

The part also carries a reference pin, so a single supply system can lift the zero point away from ground and keep a bidirectional current visible. Two common uses are a high side shunt on a 24 V rail and a bridge signal that sits on top of a large common mode offset. Where a customer wants to compare this against newer zero drift current sense amplifiers, our amplifier cross reference lists the families by common mode range and gain, and the drop in verification page sets out what to check before a swap is signed off.

Buyer questions on the INA105KP

Is the KP grade good enough for a production instrument? For a 10 bit or 12 bit front end on a 10 V span, yes. The 500 microvolt maximum offset is 0.005 per cent of full scale and the drift is 10 microvolts per degree maximum, so an uncalibrated channel holds its reading over a normal cabinet range. A 16 bit channel needs a trim at test.

Can it run on a single 5 V supply? Yes, with the reference pin set above ground so the output stays inside the amplifier's swing. The common mode range at the inputs then has to be checked against the supply, since the part was specified for split rails.

Why is the differential input impedance only 50 kilohm? The four resistors set it, and 50 kilohm is the price of a unity gain difference stage with trimmed ratios. A source above a few kilohm will load the network and add gain error, which is why a buffer is used in front of it on high impedance bridges.

Availability and ordering notes

The tube of 50 suits a build of forty units and the reel of 2500 suits the line, so the packing decides the purchase rather than the part number's electrical grade. Where the catalogue code points at the tube and the requirement is a reflow line, the order has to move to the KU reel row. We stock both packings of this family and flag the packing on the quote, and a part that has gone obsolete in one body can usually be covered from the other through our obsolete part cross reference hub.