Contact Us

DRV8906QPWPRQ1

Brand: Texas Instruments
Texas Instruments DRV8906QPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8906QPWPRQ1 — Power Management & Signal Chain | Superb Automation

DRV8906QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8906QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8906QPWPRQ1: Six Half Bridges in the Same Footprint, for Platforms That Do Not Need Eight

DRV8906QPWPRQ1 is an automotive six channel half bridge driver with SPI configuration and diagnostics in a HTSSOP (PWP) body of 24 pins. It is the six channel member of the DRV89xx-Q1 family, in the same 24 pin HTSSOP body as the eight channel part, with the same 4.5 V to 32 V supply, the same 1 A RMS per output, the same 5 MHz SPI and the same fault reporting. Two outputs are simply not bonded out, so a platform that needs six loads can use the same board outline and the same firmware image as the eight channel variant, and populate the part that matches the trim level.

Order code and package

Ordering stringDRV8906QPWPRQ1, HTSSOP, large reel
Family documentDRV8904-Q1 through DRV8912-Q1, SLVSEC9C, September 2019, revised February 2020
Channel countsix half bridges, up to three full H bridges
PackageHTSSOP (PWP), 24 pins, 7.80 mm by 4.40 mm
QualificationAEC-Q100 grade 1, minus 40 to plus 125 degrees ambient
Bus16 bit SPI, 5 MHz, daisy chain capable
PWM generatorsfour or eight generators depending on the member, per the family document
Fault pinnFAULT, open drain
Pin compatibilitysame land pattern as the four and eight channel members
Loadssmall brushed motors, stepper motors, solenoids and LED groups

Electrical parameters that decide the application

Supply range4.5 to 32 V, absolute maximum 40 V
Current per output1 A RMS continuous, 6 A maximum with outputs paralleled
High side on resistance0.75 Ohm typical, 1.1 Ohm maximum at 25 C, 1.5 Ohm at 125 C
Low side on resistance0.75 Ohm typical, 1.1 Ohm maximum at 25 C, 1.5 Ohm at 125 C
Sleep current at 13.5 V0.35 uA typical, 1 uA maximum at 25 C
Turn off time200 us
Output slew rate0.6 V per us into 27 Ohm
PWM frequency options80, 100, 260 and 2000 Hz by register
Undervoltage lockout4.0 V rising, 200 mV hysteresis
Overvoltage protection21 to 25 V rising by default, extended setting up to 35 V
Overcurrent trip2.3 A maximum, deglitch from 1 us to 40 us
Open load detection2 to 18 mA active, 113 uA passive
Logic supply3 to 5.5 V on VDD
Thermal warning and shutdownwarning flag then shutdown with a hysteresis band

Family variants and how they differ

DRV8904-Q1four half bridges, same body
DRV8906-Q1six half bridges, the part on this page
DRV8908-Q1eight half bridges, same body, two more outputs bonded
DRV8910-Q1ten half bridges, larger body
DRV8912-Q1twelve half bridges, larger body
DRV8873-Q1single H bridge with current sense, for one high current load
What the choice changesthe number of loads, not the interface or the protection
What stays identicalSPI map, fault behaviour, slew settings and open load thresholds

Points to check before this part goes on a BOM

The six channel part exists for trim levels and for the middle of a platform range. A body controller for a base vehicle may drive two mirror motors, two flap motors and two solenoids, while the top of the range adds a seat pump and a sunblind. Because the land pattern and the SPI map are shared across the family, the same board can carry the six channel part in the base and the eight channel part in the top, and the firmware can read the device identification register at start up and mask the channels that are not present. That is a cheaper way to cover a range than two separate boards.

Two outputs not bonded out is not the same as two outputs disabled. The channels that are missing do not exist in silicon on this member, so a firmware image written for the eight channel part has to read the identification register and skip the absent channels rather than write to them and wait for a fault. A write to a non existent channel returns a fault bit, which is easy to confuse with a real load fault during a first article test. Reading the identification register once at start up and building the channel mask from it removes that confusion and makes the same image safe on every member of the family.

Thermal headroom is the same per output and better per package. Six outputs at 1 A dissipate about nine watts worst case instead of twelve, so the junction runs cooler in the same body and the derating curve is more forgiving. In practice that means a board that is marginal on the eight channel part in a hot enclosure may pass with six channels loaded, provided the loads are the smaller ones. The number to check is the total dissipation in the package against the thermal resistance of the board copper, not the per channel rating, because the package limit applies to the sum.

Diagnostics behave the same way as on the eight channel part, which is the point of the family. Each channel reports open load, short to ground and short to supply, and the fault bits are latched until read. The open load detection current of 2 to 18 mA works for a motor winding and not for a high impedance load, and the passive mode with 113 uA is available when the load must not be driven during the test. For a solenoid with a flyback diode across it, the passive mode is the only one that gives a trustworthy result, because the diode conducts the active test current and hides the open circuit.

Using the same board for two trim levels

A platform that shares one board across trim levels needs three things from the driver: the same land pattern, the same register map, and an identification register that says which member is fitted. This part provides all three against the eight channel member, so the base trim can be built with six channels populated and the top trim with eight, and the same firmware image runs on both after reading the identification once at start up. The one thing to watch is the bill of materials: the two order codes are not interchangeable at the feeder without a program change, so the production line has to treat them as separate part numbers even though the board is identical. Mixing them in one reflow run is possible but needs a clear marking on the reel.

Where this order code fits

Mid range body controllers, mirror and flap loads, small solenoid banks and LED groups where six outputs are enough. It shares the footprint with the four and eight channel members, so a platform can scale without a new board. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the firmware the same as for the eight channel part? The register map is the same, but the channel mask has to be read from the identification register because two channels are absent on this member.

Can the six outputs be used as three full bridges? Yes, pairs of half bridges form full bridges, and the modes cover independent, sequential and parallel operation.

Does it need a separate 3.3 V supply? Yes, VDD is the logic supply and runs from 3 to 5.5 V, separate from the motor supply on VM.

What is the advantage over the eight channel part? Lower total dissipation for the same load count and a lower cost for trim levels that do not need eight outputs, with no change to the board or the bus.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.