Contact Us

DRV8876PWPR

Brand: Texas Instruments
Texas Instruments DRV8876PWPR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8876PWPR — Power Management & Signal Chain | Superb Automation

DRV8876PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8876PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8876PWPR: 700 mΩ with the current mirror on the die

The DRV8876PWPR is the current sense member of the DRV887x pair, published ACTIVE with a 2000 piece reel. It shares the pin out, the package and the protection block with the DRV8874 and differs in two ways that matter to a buyer: the FETs are 350 mΩ each instead of 100, so the peak current is 3.5 A instead of 6 A, and the reel carries 2000 pieces instead of 3000. Everything else in the feature list is common to the family, including the tri level control mode pin, the quad level protection mode pin, the charge pump, the spread spectrum clocking and the fault output.

The current mirror reports 1000 µA for every amp of load current, which is a higher ratio than the 450 µA of the 8874 and gives a larger signal for the same load. That extra gain costs accuracy at low currents: the mirror error is expressed as 7.5 mA below 0.15 A, 5 per cent between 0.15 and 0.5 A, and 4 per cent between 0.5 and 2 A at junction temperatures below 125 degrees, rising to 5 per cent above that. A board that uses the signal for stall detection at 2 A is comfortable; one that uses it to measure a 100 mA holding current is not.

The DRV8876PWPR rows as the addendum publishes them

Part classBrushed DC motor driver with integrated current sense and regulation
Vendor statusACTIVE, production data
Data sheetSLVSDS7B, August 2019, revised November 2019
Operating voltage4.5 V to 37 V
Peak output current3.5 A
RDS(on), each FET350 mΩ typical, 420 mΩ maximum at 24 V and 1 A
RDS(on), both FETs700 mΩ typical
Current mirror ratio1000 µA per amp
Mirror error below 0.15 A7.5 mA fixed offset
Mirror error 0.15 to 0.5 A5 per cent
Mirror error 0.5 to 2 A4 per cent below 125 degrees junction
Mirror error 0.5 to 2 A, hot5 per cent to 150 degrees junction
Sense delay1.6 µs, deglitch 0.6 µs, blanking 1.1 µs
Current regulation off time25 µs
Propagation delay650 ns
Output dead time300 ns
Supply current3 mA typical, 7 mA maximum at 24 V
Sleep current0.75 µA typical, 1 µA maximum
Undervoltage lockout4.3 to 4.6 V rising, 4.2 to 4.5 V falling
Overcurrent trip3.5 A minimum, 5.5 A maximum
Thermal shutdown160 to 175 to 190 degrees, 20 degrees hysteresis
BodyHTSSOP with PowerPAD, 16 pins, 5.00 by 4.40 millimetres
Reel rowDRV8876PWPR, 2000 pieces, large tape and reel, Active
Second live rowDRV8876PRG4, 2000 pieces, same body
Quad flat rowDRV8876RGTR, VQFN, 3000 pieces, level 1
Tube rowDRV8876PWPT, obsolete
Marking8876

Three live carriers appear for this die: two HTSSOP reels at 2000 pieces and a VQFN reel at 3000, plus an obsolete tube. The VQFN row is level 1, which means unlimited floor life, and that alone makes it the easier row for a workshop that cannot control humidity. The trade is a different land pattern, so a board that already has the HTSSOP footprint cannot take it without a revision.

Using the mirror as a current limit rather than a measurement

The regulation loop compares the IPROPI voltage, which is the mirror current through an external resistor, against the VREF pin. When the two meet, the bridge chops for the fixed 25 µs off time. That makes the limit a function of one resistor and one reference, both of which are outside the part, so the limit can be set per mechanism on the same board by changing two components. With a 1.5 k resistor, 1 A of load produces 1.5 V at the pin, and a 1.5 V reference therefore sets the limit at about 1 A.

The tolerance of that limit is the mirror error plus the resistor tolerance. At 1 A the mirror contributes 4 per cent and a 1 per cent resistor another 1 per cent, so the limit sits within about 5 per cent of the intended value, which is tighter than most mechanical stops require. The remaining error is thermal: the mirror ratio drifts with junction temperature, and the drift is already included in the two accuracy rows quoted for below and above 125 degrees.

Where the 700 mΩ part is the right choice

Applications that run below 1.5 A continuous and need a current limit without a shunt are the natural home for this row. A damper actuator, a peristaltic pump, a ticket printer feed, a lock bolt: all of them draw a stall current several times the running current, and all of them need the driver to stop pushing before the gearbox strips. The mirror gives that protection with two passive components and no shunt heat.

Above 2 A continuous the 700 mΩ bridge becomes the limit rather than the motor. The conduction loss at 2.5 A is 4.4 W at 25 degrees and over 6 W at 150, which a small pad cannot move. That is the point where the DRV8874 row, with a fifth of the resistance, is the correct part, and the two are pin compatible so the change is a bill of materials change rather than a board change.

Protection behaviour and the fault pin

Undervoltage, overcurrent and overtemperature all pull the same fault pin low. Overcurrent can either retry every 2 ms or latch the outputs off, depending on the resistor fitted to IMODE, and that resistor is read at power up. A latch is the safer choice for a mechanism that a person can reach, because a retry loop into a jammed load heats the motor winding even when the driver survives.

The thermal shutdown threshold is 175 degrees nominal with 20 degrees of hysteresis, which is a narrower window than the 40 degrees of the eight pin family. The narrower window means faster recovery and more frequent retries, so a system that relies on the driver to survive a sustained stall will see a fault train rather than a single event.

Buying DRV8876PWPR

The 2000 piece reel is smaller than the 3000 of the automotive row, which suits a product with moderate volume. Both HTSSOP rows and the VQFN row are live, so a buyer has a choice of carrier and a choice of floor life. The level 3 HTSSOP reel needs a bake if it is opened for more than 168 hours, and the level 1 VQFN reel does not, which is a real scheduling advantage on a low volume line that opens and closes reels.

The obsolete tube row still appears in older drawings. A customer buying tubes for service stock has to move to a reel, and a broken reel from a distributor is the practical answer when the annual service demand is under a hundred pieces.

Questions that arrive with this part number

Whether the mirror can be used to measure motor current for a torque loop is the first question, and the answer is that it can report a load, not a calibrated current. The second is whether the regulation loop can be disabled. It can, by holding VREF at a level the mirror will never reach, and then the part behaves as a plain bridge with overcurrent protection. The third is whether the 25 µs off time can be changed. It cannot, so the chopping frequency is fixed by the load inductance and the supply voltage rather than by a register.

One more number belongs in the quote: the input current of 50 µA typical and 75 µA maximum at 5 V means the logic pins can be driven directly from a 3.3 V microcontroller with no level shift, and the 100 kΩ internal pull down holds a floating input in the off state.

For a build that needs the same footprint at higher current, the pin to pin page lists the four family rows against each other, and the shortage recovery page explains how we handle a move between them when one reel is unavailable.