Contact Us

DRV8873HPWPRQ1

Brand: Texas Instruments
Texas Instruments DRV8873HPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8873HPWPRQ1 — Power Management & Signal Chain | Superb Automation

DRV8873HPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8873HPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8873HPWPRQ1: A 10 A Automotive H Bridge With SPI Diagnostics and Spread Spectrum

DRV8873HPWPRQ1 is an automotive H bridge motor driver with integrated current sensing in a HTSSOP (PWP) body of 24 pins. It drives 10 A peak from 4.5 V to 38 V with a combined FET resistance of 150 mOhm at 25 C, reports current on an IPROPI pin at 1100 A per A, and takes its settings either from pins or from a SPI port depending on the letter in the string. The H string is the SPI member, the S string the pin controlled one, and both are qualified to AEC-Q100 grade 1.

Order code and package

Ordering stringDRV8873HPWPRQ1, large reel, 2000 pieces
Family documentDRV8873-Q1, SLVSDY7B, revised January 2021
PackageHTSSOP (PWP), 24 pins with PowerPAD, 2000 piece reel
Lead finishNIPDAU
Moisture levelLevel 3, 260 C, 168 hour floor life
Body marking8873HQ for the SPI member, 8873SQ for the pin member
Temperature rangeminus 40 to plus 125 degrees ambient, AEC-Q100 grade 1
Sibling rowDRV8873SPWPRQ1, same body, pin control instead of SPI
Prototype rowPDRV8873SPWPRQ1, preproduction, marked obsolete on the addendum
QualificationAEC-Q100 grade 1 and Functional Safety-Capable documentation

Electrical parameters that decide the application

Supply range4.5 to 38 V operating
Peak output current10 A
FET resistance, high side plus low side150 mOhm at 25 C, 250 mOhm at 150 C
Sleep current15 to 30 uA with nSLEEP low at 13.5 V
Active current5 to 10 mA at 13.5 V with the bridge disabled
Internal logic regulator5 V, 4.7 to 5.3 V window at a 2 mA load
Current mirror scaling1100 A per A on IPROPI
Logic thresholds0.8 V low, 1.6 V high, 150 mV of hysteresis
Slew rate settingsEight steps from 53.2 V per us down to 2.6 V per us
Output dead time500 ns at the middle slew setting
Sleep and wake timing50 us to shut down, 1.5 ms to wake, 5 to 20 us for a fault reset pulse
PWM frequencyup to 400 kHz
Body diode drop0.8 V at 1 A
Thermal shutdownwith hysteresis, and a warning threshold on the SPI member

Family variants and how they differ

DRV8873HSPI control, full diagnostics in registers, the part on this page
DRV8873SPin control, fault reported on nFAULT only
Interface modesPH and EN, PWM with IN1 and IN2, or independent half bridge control
Current senseIPROPI on both members, one pin per bridge
Slew rate controlEight steps on the S member by pin, register settings on the H member
Spread spectrumClock dithering for emissions, enabled by register on the H member
What the SPI addsOpen load detection, overcurrent threshold choice and fault history

Points to check before this part goes on a BOM

The two letters are two products. The S member sets its mode with resistors on the MODE pin and reports a fault as a single open drain line, which is enough for a seat motor. The H member puts the same bridge behind a SPI port where the overcurrent threshold, the slew rate, the spread spectrum setting and the fault history are all readable and writable, which is what a body control module needs when it has to tell a dealer which actuator failed and why.

The 10 A peak and the 150 mOhm pair have to be read together. At 5 A the conduction loss is 1.25 W and the 24 pin HTSSOP with a soldered pad rises roughly 30 C above ambient, which is comfortable. At 10 A the same arithmetic gives 15 W, which no package of this size can pass to a board without a heatsink area, so the 10 A figure applies to a stall transient of a few milliseconds, not to a continuous load. A throttle body that holds 3 A indefinitely sits at about 0.45 W and is well inside the rating.

IPROPI is a current mirror, not a shunt amplifier. The pin sources 1/1100 of the bridge current, so 5 A produces 4.5 mA, and a resistor to ground turns that into a voltage the controller can read. The mirror is only accurate while the FETs are in linear operation, and it saturates near the supply rail, so a firmware that integrates the IPROPI voltage to estimate position has to discard samples taken during freewheeling and during a stall at full rail.

Slew rate control is how this part passes an emissions test. The eight settings run from 53.2 V per us down to 2.6 V per us, and the slowest setting turns a 100 ns edge into a 15 us ramp, which moves the switching energy out of the 30 MHz to 100 MHz band that harnesses radiate from. The cost is dissipation: every edge spends longer in the linear region, so a 5 A load at the slowest setting adds several watts, and the choice is a compromise between the EMC chamber and the thermal chamber.

What the automotive qualification actually covers

Grade 1 means the part is qualified to 125 C ambient, and the addendum prints the whole family at minus 40 to plus 125. The junction runs hotter and the overcurrent and thermal shutdown thresholds are set with that in mind, so a bridge that trips at 5 A on the bench may trip earlier inside a door module that has soaked at 85 C for an hour, because the FET resistance rises by two thirds between 25 C and 150 C.

Functional Safety-Capable means the vendor supplies a safety manual and failure mode information rather than that the part is certified to a level. A system that claims ASIL B has to build its own diagnostic coverage, and the SPI member helps because the fault registers distinguish an overcurrent from an open load from a thermal warning, which the pin member cannot do.

The supply is the other half of the automotive story. A load dump takes the rail to tens of volts for a few hundred milliseconds and a cold crank takes it below 6 V, and the part is rated for neither condition on its own. The 38 V operating ceiling is a working limit, not a survival limit, so a module that must live through a load dump needs a clamp in front of the bridge, and the 4.5 V floor means the bridge drops out during a cold crank unless the module holds the rail up with a boost stage.

Where this order code fits

Body control modules and pump controllers that need a documented fault path start from the power management cross reference page Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Incoming Inspection Plan page.

Questions buyers ask

Does the SPI member work without the SPI bus? It powers up with register defaults that are usable, and the bridge will drive a load from the input pins, but the overcurrent threshold stays at its default and the diagnostics are not readable. A board that leaves the bus unconnected loses the reason the H string exists.

What sets the current limit? The bridge has fixed overcurrent protection and a separate IPROPI output. The limit itself is internal and selected by register on the H member, so the external resistor on IPROPI sets the voltage scale for the controller and not the trip point.

Is the PDRV8873SPWPRQ1 row orderable? The addendum marks it preproduction and obsolete, with the quantity column reading call TI. It exists as a record of a prototype build and should not go into a production board.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.