DRV8871DDAR
Product Specifications
DRV8871DDAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8871DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8871DDAR: A 45 V Brushed Driver That Sets Its Current With One Resistor
DRV8871DDAR is a brushed DC motor driver with resistor set current regulation in a SO PowerPAD (DDA) body of 8 pins. It works from 6.5 V to 45 V and delivers 3.6 A peak into one brushed motor, with total bridge resistance of 565 mΩ and a current regulation loop that needs no sense resistor and no analog reference. The trip point is set by a single resistor to ground, the decay behaviour follows the two input pins, and the whole part is an eight pin SO with a thermal pad at 4.9 mm by 6.0 mm.
Order code and package
| Ordering string | DRV8871DDAR |
| Family document | DRV8871, SLVSCY9B, revised July 2016 |
| Package | SO PowerPAD (DDA), 8 pins, 4.9 mm by 6.0 mm with an exposed pad |
| Reel and packing | 2500 pieces on a large reel |
| Moisture level | Call the vendor for the reel specific rating on the plain row |
| Body marking | 8871 |
| Temperature range | minus 40 to plus 125 degrees |
| Tube sibling | DRV8871DDA, listed as obsolete in the current addendum |
| Interface | Two logic inputs, PWM on either or both |
| Current setting | One resistor from the ILIM pin to ground |
| Bridge | Integrated, four N channel FETs with a charge pump |
Electrical parameters that decide the application
| Supply range | 6.5 to 45 V |
| Peak output current | 3.6 A |
| Bridge resistance | 307 mΩ source and 258 mΩ sink at 24 V and 1 A, 565 mΩ for the pair |
| Current sense constant | 64 kV per amp, so the resistor value follows the target current |
| Off time | 25 us fixed, no external setting |
| Blanking time | 2 us |
| Supply current | 3 mA typical and 10 mA maximum with no load |
| Sleep current | 10 uA typical |
| Undervoltage | 6.1 to 6.4 V falling, recovery at 6.5 V, 100 to 180 mV of hysteresis |
| Overcurrent trip | 3.7 A minimum, 4.5 A typical, 6.4 A maximum |
| Overcurrent timing | 1.5 us of deglitch and 3 ms before a retry |
| Thermal shutdown | 175 C typical with 40 C of hysteresis |
| Dead time | 220 ns |
| Output delay | 0.7 to 1.0 us from input to output |
Family variants and how they differ
| DRV8870 | The same footprint with a shunt resistor path, 6.5 to 45 V and 565 mΩ |
| DRV8251 | 4.5 to 48 V and 450 mΩ with a shunt, for a higher voltage rail |
| DRV8251A | 4.5 to 48 V and 450 mΩ with an internal mirror instead of a shunt |
| DRV8231 | 4.5 to 33 V and 600 mΩ with a shunt |
| DRV8231A | 4.5 to 33 V and 600 mΩ with a mirror |
| DRV8871DDA | Tube packing, obsolete in the current addendum |
| Pin compatibility | The family shares the eight pin footprint, so the current sense method can be changed on one board |
Points to check before this part goes on a BOM
The current limit is set by one resistor, and the constant that converts it is 64 kV per amp. A 64 kΩ resistor gives about 1 A, a 32 kΩ resistor about 2 A, and a 16 kΩ resistor about 4 A, which is beyond the 3.6 A rating. The resistor tolerance sets the trip directly, so a one per cent part is worth the small cost when the trip has to protect a gearbox rather than just the bridge.
The off time is fixed at 25 us and cannot be changed, which suits a motor with an inductance in the hundreds of microhenries and limits the part on a very low inductance load. With a small coreless motor the current rises and falls substantially within each 25 us window, and the ripple appears as torque ripple and as acoustic noise. A higher inductance winding sees the same window as a smooth current.
The undervoltage threshold sits at 6.3 V, which is not a 5 V compatible part. A 5 V motor rail, common in small mechanisms, is below the operating range entirely, and a 6.5 V rail sits right on the recovery threshold, so a supply that sags during start up drops the bridge out. That is the reason the smaller family members with a 4.5 V floor exist.
The 3.6 A figure is peak and the thermal path is the real constraint. At 565 mΩ the bridge dissipates about 0.6 W at 1 A and more than 7 W at 3.6 A, which the eight pin SO can only hold for short periods. A current limit set near the peak rating protects the motor but not the package, so the resistor is usually chosen well below the peak, and the thermal shutdown at 175 C is the last line of defence.
Sleep is entered by pulling both inputs low, and the part takes 1 to 1.5 ms to reach it. That is long enough that a firmware which toggles the inputs at a high rate to brake and release never reaches sleep, and short enough that a genuine idle period costs almost nothing. The 10 uA sleep current is what allows the rail to stay connected in a battery product.
What the resistor set current loop is good for
A printer feed mechanism, an appliance damper or a small industrial actuator usually has a mechanical end stop, and the current rises sharply when the mechanism reaches it. With the trip set just above the running current, the bridge folds back at the stop and the mechanism stalls without burning the motor. No sense resistor, no amplifier and no firmware loop are needed, which is the reason this part exists next to the shunted family members.
The loop chops with a fixed 25 us off time, so the current waveform at the trip point is a sawtooth rather than a flat line. The average current is what the mechanism sees, and the peak is what the bridge and the motor insulation see, so a trip set at 2 A has peaks somewhat above that figure and the margin has to allow for it.
Picking between the four family members
The four parts share an eight pin footprint and differ in supply range, resistance and how the current is sensed. The DRV8871 and DRV8870 reach 45 V, the DRV8251 pair reaches 48 V with lower resistance, and the DRV8231 pair stops at 33 V. Choosing the mirror version removes the sense resistor and its heat, while the shunt version leaves the sense signal available on a pin for a controller that wants to measure it.
Because the footprint is shared, the choice can be deferred until the thermal and the sensing requirements are known, and a board can even be laid out to accept both by leaving the sense resistor position unpopulated. That is a common way to keep a second source open on a programme that has a long production life.
Where this order code fits
The part fits a 12 V or 24 V brushed mechanism where the current has to be capped at a mechanical end stop and the board has room for one resistor but not for a shunt and an amplifier. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
How is the current limit calculated? The vendor constant is 64 kV per amp, so the resistor is 64 kΩ divided by the target current. 64 kΩ gives about 1 A, 32 kΩ about 2 A. A one per cent resistor keeps the trip within a per cent before the tolerance of the internal reference is counted.
Can it run from a 5 V rail? No. The operating range starts at 6.5 V and the undervoltage trips at 6.1 to 6.4 V, so a 5 V motor supply never brings the bridge up. The lower voltage members of the family start at 4.5 V.
What sets the decay mode? The two input pins. Driving both high is brake with the low side FETs on, driving one high and the other with PWM gives slow decay during the off portion, and a reversal of the inputs gives fast decay. The part has no separate decay pin.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.