Contact Us

DRV8870DDAR

Brand: Texas Instruments
Texas Instruments DRV8870DDAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8870DDAR — Power Management & Signal Chain | Superb Automation

DRV8870DDAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8870DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8870DDAR: 3.6 A brushed DC motor driver in an eight pin HSOP

DRV8870DDAR is a single H-bridge brushed DC motor driver in a HSOP body of 8 pins. It drives one brushed motor or one winding of a stepper from 6.5 V to 45 V with 3.6 A of peak current, using two logic inputs for direction and PWM. The DDA order code is the eight pin HSOP with a PowerPAD.

Order code and package

Order codeDRV8870DDAR
Package8-pin HSOP with PowerPAD, 4.9 mm by 6.0 mm
Packingtape and reel
Motor supply6.5 V to 45 V on VM
Peak current3.6 A
ControlIN1 and IN2 logic inputs, PWM for speed
Current regulationexternal sense resistor on ISEN, analog reference on VREF
Protectionunder voltage, over current, thermal shutdown, automatic recovery

Electrical parameters that decide the application

High side on resistance307 milliohm typical, 360 milliohm maximum at 24 V
Low side on resistance258 milliohm typical, 320 milliohm maximum at 24 V
Output dead time220 ns
ISEN amplifier gain10 V per V, 9.4 to 10.4 over temperature
Under voltage lockout6.1 V to 6.4 V falling, 100 to 180 mV hysteresis
Over current trip4.5 A typical, 3.7 A to 6.4 A window
Thermal shutdown175 degrees junction
Sleep current10 microampere at 12 V

Family variants and how they differ

DRV8870PWM interface with an external sense resistor, this order code
DRV8871integrated current sense set by a resistor, no ISEN pin
DRV8872adds a fault output for over current reporting
DRV8870DDAsame part in a tube instead of a reel

Points to check before this part goes on a BOM

The 565 milliohm headline on resistance is the sum of the high side and low side figures at 24 V, and it is what turns into heat at the motor current rather than at the peak rating. At 2 A continuous the bridge dissipates 2.3 W, and the eight pin HSOP carries that through the PowerPAD, so the copper area under the part is the real current limit on a small board.

Peak current and continuous current are different numbers here. The 3.6 A rating is a peak, the over current protection trips between 3.7 A and 6.4 A, and the thermal path decides how long a 3 A stall can last before the 175 degree shutdown takes the outputs down and the automatic recovery brings them back.

Current regulation uses the ISEN amplifier at a gain of 10 with the external shunt, so the trip level is the reference voltage divided by ten times the shunt value. A 3.3 V reference with a 0.15 ohm shunt limits at 2.2 A, and the reference has to stay above about 0.3 V where the accuracy is specified.

The 220 ns dead time is fixed inside the part and the outputs are driven through it on every direction change. At 20 kHz PWM that is 0.44 percent of the period, which is small, but at 100 kHz it becomes 2.2 percent and shows up as a loss of duty range at low speed rather than as a fault.

Both inputs low put the part into sleep at about 10 microampere, and that is the state to use for a parked actuator. Leaving one input high holds the bridge in a braking state and keeps the supply current at the operating figure even when the motor is not moving.

The under voltage lockout falls between 6.1 V and 6.4 V with 100 to 180 mV of hysteresis, so a 6.5 V rail that sags during a stall unwinds the outputs. A build specified at 6.5 V minimum has no margin at the bottom of its supply tolerance and should start from a 9 V or 12 V rail.

Automatic fault recovery is convenient and it hides a thermal problem. A motor that stalls repeatedly cycles between drive and shutdown without a flag, so a product that must report a jam needs the current sense output read by the controller rather than the fault behaviour alone.

PWM frequency has a practical ceiling set by the 220 ns dead time and by switching loss. At 20 kHz the bridge is comfortable, and at 50 kHz the dead time is 1.1 percent of the period and the switching loss starts to compete with conduction loss. Above the audible band the choice is usually 20 kHz to 25 kHz for that reason.

A brushed motor returns energy when it is braked or back driven, and the supply rail absorbs it. A 100 nF bypass capacitor is not enough for a 2 A motor; the bulk capacitor at VM has to be sized for the current the motor can return, and a rail that rises under braking is the usual sign that it was sized from the data sheet example rather than from the load.

Where this order code fits

It is used in printers, appliances, industrial actuators, valve and damper drives, vending mechanisms and other small machines that need bidirectional control from two logic lines. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can it drive a stepper motor? One winding, yes. The part has a single H-bridge, so a bipolar stepper needs two devices and the step sequencing has to come from the controller.

Where does the current sense resistor go? Between the ISEN pin and ground, with the motor return through it. The ISEN amplifier gain of 10 converts the shunt drop into the comparison against VREF.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.