DRV8847RTER
Product Specifications
DRV8847RTER
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8847RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8847RTER: two 1 A bridges in a 3 mm square
The DRV8847RTER is the 16-pin WQFN body of the DRV8847, a dual H-bridge driver for low voltage mechanisms. The supply range is 2.7 V to 18 V with 20 V absolute maximum, each bridge carries 1 A rms at 25 C and 2 A rms in parallel mode, the on resistance is 1000 mOhm high side plus low side above 5 V, and the current regulation loop has a fixed 20 microsecond off time. The part is built for the band where a 12 V rail and a one amp motor are the normal case.
The interface is the flexible part. Four pins give independent control of two bridges, two pins give a phase and enable interface for one stepper, and the bridges can be tied in parallel for a single 2 A motor. A torque scalar pin scales the output current to 50 percent, which is a way to run a mechanism at reduced torque without changing the sense resistor, and a sleep pin brings the part down to 1.7 microamps.
Protection covers undervoltage lockout, overcurrent on each FET, short circuit, open load detection and thermal shutdown, with an nFAULT output. The I2C variant of the same circuit, DRV8847S, adds registers for detailed diagnostics and multi slave operation, so a system that has to report which bridge failed uses the S part and a system that only needs to stop uses this one.
The package family is unusual in a useful way: the same circuit is published in a 16-pin TSSOP without a thermal pad, a 16-pin HTSSOP with a PowerPAD and the 16-pin WQFN. That gives a hand solderable body for prototypes and a thermally enhanced body for production, all from one order code family, which is the pattern we see in printer and appliance builds.
Key data for the DRV8847RTER
| Operating supply | 2.7 V to 18 V, absolute maximum 20 V |
| Outputs | Two H-bridges, or one bipolar stepper, or four independent half bridges |
| Current | 1 A rms per bridge at 25 C, 2 A rms in parallel mode, 2 A peak |
| On resistance | 1000 mOhm high side plus low side above 5 V at 25 C |
| Interface | Four pin independent, two pin phase and enable, or parallel bridge |
| Current regulation | Fixed 20 microsecond off time, torque scalar to 50 percent |
| Diagnostics | Open load detection, overcurrent, thermal shutdown, nFAULT |
| Sleep current | 1.7 microamps typical at 12 V and 25 C |
| Temperature | Minus 40 C to plus 125 C operating |
Body, packing and marking data
| Body in this code | 16-pin WQFN, the RTE outline, 3.00 mm by 3.00 mm, 9 mm squared with a thermal pad |
| Other bodies | 16-pin HTSSOP, the PWP outline, 5.00 mm by 6.40 mm; 16-pin TSSOP, the PW outline, 5.00 mm by 6.40 mm without a thermal pad |
| Carrier | Tape and reel; the count per reel is read from the vendor addendum row for this order code |
Reading the code before you buy it
DRV8847 is the circuit, RTE is the 3 mm WQFN and the trailing R is the reel. The DRV8847S is a separate circuit with an I2C port and the same footprint options, so a board that talks to the driver over I2C needs the S and a board that only needs to move does not. The two are close enough in price that the choice is usually made by whether the controller has spare pins or spare bus bandwidth.
The vendor lists DRV8421 as a newer low cost alternative with a pin to pin multi sourcing option, which is a rare published statement in this class and worth knowing when this order code goes short. The DRV8421 runs 18 V and 2 A with a similar interface, so the electrical envelope is close and the difference is in the current reference and the diagnostics.
The three body options matter at the sourcing desk: the TSSOP without a thermal pad reflows like a standard logic part and is easy to rework, and the two thermally enhanced bodies are for production. A prototype built with the TSSOP can be moved to the QFN for volume without changing the circuit. Our pin to pin cross reference page lists the body options we can quote for each of these order codes.
Where the DRV8847RTER fits
Point of sale printers and label printers use it for the feed motor and the cutter, which are two small brushed motors on a 12 V rail. Home appliances and white goods use it for a damper, a dispenser or a fan flap where the motor is under an amp and the driver has to survive a 125 C ambient behind a panel.
Video surveillance cameras with pan and tilt use one bridge per axis, and the 3 mm body fits behind the dome next to the image sensor. Office automation, gaming machines and mechatronic modules use it for the same reasons: two motors, one package, a current limit that protects the mechanism and open load detection that reports a disconnected motor to the controller.
Where it does not fit is a stepper that needs fine microstepping: the step modes here stop at the half or quarter step level depending on the interface, and a mechanism that needs 1/256 uses a dedicated stepper driver. Our BOM scrubbing page is where we catch that mismatch before a build starts.
Questions we get on this code
How is the current limit set? An external sense resistor per bridge sets the trip point against the fixed off time loop. A 0.1 Ohm resistor gives 2 A at a 200 mV reference, and the torque scalar can halve that without changing the resistor.
Can one bridge drive 2 A? Yes, in parallel mode, where the two bridges are tied together and the current is shared. That mode requires the outputs to be shorted on the board and the control pins to be driven together, and the thermal path has to carry the combined loss through one pad.
Why 1000 mOhm when a newer part is 400? Because this is a low voltage part built on a smaller die per bridge. At 1 A rms the loss per bridge is about 1 W, and the 125 C rating is what makes that acceptable in a warm enclosure.
Does open load detection work with a motor connected? It works by sensing the current in the bridge, so it reports a disconnected or an open winding. A motor with a very high resistance at the end of its life can also trigger it, which is why the fault has to be read together with the current measurement.