Contact Us

DRV8837DSGR

Brand: Texas Instruments
Texas Instruments DRV8837DSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8837DSGR — Power Management & Signal Chain | Superb Automation

DRV8837DSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8837DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8837DSGR: A 2 mm H Bridge for a 1.8 A Load on a Single Cell Rail

DRV8837DSGR is a low voltage H bridge driver with the FETs inside in a WSON (DSG) body of 8 pins. It drives one brushed motor or a solenoid from a motor rail anywhere between 0 V and 11 V while the logic side runs from 1.8 V to 7 V, and the whole bridge sits in a 2.00 mm by 2.00 mm body with an exposed pad. Total resistance is 280 mΩ, peak drive current is 1.8 A, and sleep current is capped at 120 nA, which is what allows the part to hang on a battery rail without a load switch.

Order code and package

Ordering stringDRV8837DSGR
Family documentDRV883x, SLVSBA4F, revised April 2021
PackageWSON (DSG), 8 pins, 2.00 mm by 2.00 mm with an exposed pad
Reel and packing3000 pieces on a large reel, NiPdAu lead finish
Moisture levelLevel 1, 260 C peak, unlimited floor life
Body marking837
Temperature rangeminus 40 to plus 85 degrees
Green siblingDRV8837DSGRG4, the same die with the green material declaration
InterfacePWM with IN1 and IN2, the DRV8838 in the same family takes PH and EN instead
EnablenSLEEP pin, low for sleep
BridgeIntegrated, four N channel FETs with an internal charge pump

Electrical parameters that decide the application

Motor supply0 to 11 V on VM
Logic supply1.8 to 7 V on VCC
Output current1.8 A maximum drive current
Bridge resistance280 mΩ typical for high side plus low side at 800 mA
Motor supply current1.5 mA typical with no PWM
Sleep current120 nA maximum
Logic thresholdsLow below 0.25 to 0.38 of VCC, high above 0.46 of VCC
Input hysteresis0.08 of VCC
UndervoltageVCC falling, 1.9 V typical
OvercurrentAnalog limit on each FET, followed by a deglitch and an automatic retry
Thermal shutdown160 C typical
Output delay160 ns and 200 ns depending on the edge, at 5 V and 20 Ω

Family variants and how they differ

DRV8837DSGTThe same die on a 250 piece small reel for prototype quantities
DRV8837DSGRG4Green material declaration on the standard 3000 piece reel
DRV8838DSGRPH and EN interface instead of IN1 and IN2, otherwise the same bridge
IN1 high, IN2 lowForward, with the bridge driving OUT1 high
IN1 low, IN2 highReverse
Both high or both lowBrake, both low side FETs on
nSLEEP lowSleep, 120 nA maximum, the bridge is high impedance
PWM on one inputSpeed control with slow decay during the off portion

Points to check before this part goes on a BOM

The motor rail can sit at 0 V while the logic rail stays alive, which is unusual and useful. A camera module or a lens actuator often has its motor supply switched off while the control side is still powered, and the part keeps its inputs defined in that state instead of latching into an unknown condition. The 11 V ceiling is what limits the part to single cell and two cell products.

The 1.8 A figure is a peak drive current, and the package has to be judged on heat rather than on that number. With 280 mΩ across the bridge, a continuous 1.8 A load dissipates close to a watt in a 2 mm by 2 mm body, which only works with a solid copper pad and a short duty cycle. A toy or a camera actuator that moves for a second at a time is well inside the package, a continuous conveyor is not.

Both inputs high is brake, not coast, and both inputs low is sleep, not brake. The two states are one logic step apart, and a controller that drives both inputs low to stop the motor has actually put the part to sleep and disabled the bridge. Coast requires one input high and the other driven with a PWM that is fully off, or an external arrangement, because this part has no dedicated coast state.

The input thresholds are ratiometric to VCC, so the same 1.8 V logic high that works with a 3.3 V rail does not work with a 7 V rail, where the high threshold is above 3.2 V. Systems that mix a 5 V logic domain with a 1.8 V one need level shifting on the inputs, and the 20 V absolute maximum that some gate drivers allow does not exist on this part.

Sleep current of 120 nA is the number that removes a load switch from a battery product. The part draws essentially nothing when nSLEEP is low, so the motor rail can be permanently connected and the firmware sleeps the driver instead of cutting the rail. The quiescent current in active mode, 1.5 mA with no PWM, is the figure that matters when the mechanism is idle but not sleeping.

Where a 2 mm bridge earns its space

Camera focus and zoom actuators, small toys, electronic locks and wearable mechanisms all need a bridge that is smaller than the connector that feeds it. The 2 mm body with an exposed pad fits under a camera module or beside a battery connector, and the 1.8 V logic compatibility means it can be driven straight from a low voltage microcontroller without a level shifter.

The price of that size is thermal headroom and a modest voltage ceiling. A 6 V motor with a 1 A stall is comfortable, an 11 V motor at 1.5 A continuous is not, and the 85 degree ambient limit rules the part out of anything that has to run hot. A product that needs 12 V or a higher continuous current moves to the larger family members with a bigger body.

Brake, coast and sleep in firmware

The four combinations of the two inputs give forward, reverse, brake and sleep, and the missing state is coast. A controller that wants the motor to freewheel has to hold one input high and pulse the other, or accept brake. That is a firmware decision that has to be made before the board is built, because the mechanical behaviour of a brake and a coast are quite different on a mechanism with inertia.

The other firmware detail is the retry after an overcurrent event. The part limits the current analogically, and if the limit persists past the deglitch it disables the bridge and retries automatically. A controller that keeps commanding the same duty into a jammed mechanism therefore sees a series of retries rather than a single fault, and the stall detection has to be built around that pattern.

Where this order code fits

The part is chosen for a single cell or two cell product where a small brushed motor, a lens actuator or a solenoid has to be driven from a logic rail that is already on the board. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is the output current 1.8 A continuous? No. It is the maximum drive current, and the practical continuous figure is set by the 280 mΩ bridge in a 2 mm body. Short moves at 1.8 A are fine, a continuous 1.8 A load is not, and the 85 degree ambient limit closes the case.

What is the difference from the DRV8838? The bridge is the same and the order code changes the interface. The DRV8837 takes IN1 and IN2 as a PWM pair, the DRV8838 takes PH and EN, which suits a controller that already produces a direction pin and a speed pin.

Can the motor supply be removed while the logic stays on? Yes, the motor rail may sit at 0 V with VCC still present, and the inputs stay defined. That is one of the reasons the part is used in camera modules where the actuator rail is switched separately from the control rail.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.