Contact Us

DRV8803PWPR

Brand: Texas Instruments
Texas Instruments DRV8803PWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8803PWPR — Power Management & Signal Chain | Superb Automation

DRV8803PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8803PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8803PWPR: Four Protected Low Side Switches With the Clamp Diodes Already Inside

DRV8803PWPR is a four channel low side driver in a HTSSOP (PWP) body of 16 pins. It switches four inductive loads to ground from a supply between 8.2 V and 60 V, with 2 A available on one channel or 1 A on all four at 25 C in this body, clamp diodes built in for each output, and an overcurrent trip that reports on a fault pin.

Order code and package

Ordering stringDRV8803PWPR
FamilyDRV8803 quad low side driver, document SLVSAW5D revised December 2024
PackageHTSSOP with thermal pad, PWP body, 16 pins, 5.00 mm by 6.40 mm nominal
Other bodiesSOIC DW with 20 pins and SOT-23-THIN DYZ with 16 pins
Reel and packing2000 pieces on a large reel, NiPdAu lead finish
Moisture levelLevel 2, 260 C peak, one year floor life
Part markingDRV8803PW
Tube and other rowsDRV8803DW is printed Obsolete, the DYZ body ships 3000 on a large reel
Operating supply8.2 V to 60 V
Output rating in this body2 A on one channel or 1 A on all four at 25 C with proper copper
Control interfaceOne input per channel plus an enable, all with internal pulldowns

Electrical parameters that decide the application

On resistance500 milliohm typical in the PWP and DW bodies, 400 milliohm in the DYZ body, at 24 V and 700 mA
Clamp diodesIntegrated on every output, so an inductive load does not need an external diode
Overcurrent protectionA fixed trip level per channel, with a deglitch time and an automatic retry
Retry behaviourThe channel re-enables after the retry interval instead of latching off
PWM capability0 to 100 kHz on the inputs, which is enough for a solenoid hold current scheme
Under voltage lockout8.2 V typical on the rising supply, all outputs off below it
Fault outputOpen drain, low on over temperature or overcurrent, needs an external pull up
Enable pinA high on the enable pin disables all four outputs at once
Thermal protectionShutdown with hysteresis, reported on the fault pin
Output leakageQuoted with the outputs off, which matters for a battery load that must not drain
Rise and fall timesQuoted with a resistive load at 24 V and 700 mA
Ground pathThe thermal pad also carries the return current, so the copper area is part of the circuit

Family variants and how they differ

DRV8803DYZRThe SOT-23-THIN body at 1.9 A on one channel and 0.9 A on four, 3000 on a reel
DRV8803DWRThe 20 pin SOIC body at 1.5 A and 0.8 A, 2000 on a large reel
DRV8844Four half bridges when the load needs to be driven both ways rather than only to ground
DRV8804The same low side arrangement with a serial interface for a controller short of pins
DRV8860A low side driver with the shift register and diagnostics on board
DRV777A smaller low side driver for a relay bank that draws less current

Points to check before this part goes on a BOM

The current rating is per channel and it depends on how many channels are on. One channel can carry 2 A in this body, four channels at once only 1 A each, because the package has to pass four times the heat through the same pad. A board that sizes the copper for the single channel figure and then runs four solenoids at once will reach thermal shutdown.

The clamp diodes are inside the part, which is why there is no external diode on the outputs. They clamp the turn off transient of an inductive load to the supply rail, and that means the supply has to be able to absorb the energy or have a capacitor that can. A solenoid driven from a stiff bench supply behaves differently from the same solenoid on a battery with a long cable.

The overcurrent protection retries rather than latching. That is convenient for a load that has an inrush, and it is a problem for a shorted solenoid, because the channel keeps retrying and heating. Systems that must not retry have to detect the fault pin and disable the channel from the controller, since the part will keep trying on its own.

The thermal pad is the return path as well as the heatsink. Current flows from the load into the output pin, through the FET and out through the ground pins and the pad, so the copper under the pad carries the full load current. A pad connected with a single via to a ground plane adds resistance and inductance in the load path, and that shows up as a slower turn off.

Nothing in this part limits the voltage across the load. It switches the low side, so the high side of the load sits permanently at the supply, and a load that is accessible to a user stays live even when the driver is off. That is a safety consideration for a product where the load can be touched, and it usually forces a high side switch or a relay in series.

Relays, solenoids and a unipolar stepper

Four low side switches cover a lot of the small loads on an instrument. Four relays with coils rated under an amp, four solenoids in a valve manifold, or a unipolar stepper with a common centre tap all map onto this part without external drivers or diodes. The clamp diodes handle the coil turn off, and the enable pin gives a single point to drop everything.

A unipolar stepper is the case where the PWM capability helps. Holding current can be reduced after the step by chopping the enable or the channel input, and a 100 kHz capability means the chop is inaudible. That cuts the coil heating in a mechanism that holds position for long periods, which is the usual reason a valve or a damper actuator overheats.

Why a protected low side is not a high side switch

A low side driver is the cheapest way to switch a load, because the gate drive is referenced to ground and no charge pump is needed. Its limitation is that the load stays connected to the supply, so any fault in the wiring leaves the supply on the load. For a relay coil that is acceptable, for a heater or an actuator a user can reach it is not.

The alternative is a high side switch with its own charge pump and current sense, which costs more and takes more board space. Products mix the two: a high side switch on the output that a user can touch, a low side driver on the internal loads. A BOM review that asks why both appear usually finds this split behind the decision.

Where this order code fits

The part is used where several small inductive loads, relays, solenoids or a unipolar stepper, have to be switched to ground from a 12 V to 48 V rail. Teams comparing it with a neighbouring part start from our OEM Procurement page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Do the outputs need external flyback diodes? No. Each output has a clamp diode to the supply rail inside the package, which is what makes the part usable with a relay coil without extra parts. The supply still has to absorb the returned energy, so a bulk capacitor on the rail is normal.

Why do the four channels carry less current than one? Because the package has one thermal path. A single channel dissipates its own loss, four channels dissipate four times as much through the same pad, so the allowed current per channel drops to 1 A in this body. The DYZ body has a different pad and different numbers.

Does the part latch off after an overcurrent? No. It trips, waits, and retries by itself. That handles an inrush and it also keeps a shorted load cycling. A controller that needs a hard stop has to read the fault pin and drop the enable or the channel input.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.