Contact Us

DRV8801RTYR

Brand: Texas Instruments
Texas Instruments DRV8801RTYR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8801RTYR — Power Management & Signal Chain | Superb Automation

DRV8801RTYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8801RTYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8801RTYR: A Full Bridge With a Sense Resistor and an Analog Current Output

DRV8801RTYR is a full bridge driver with current feedback in a QFN (RTY) body of 16 pins. It drives one brushed motor or one stepper winding from 8 V to 36 V at up to 2.8 A peak, with a PHASE and ENABLE interface and a sense resistor in the low side path. The VPROPI pin puts out five times the sense voltage, which gives the controller an analog current reading without a separate amplifier, and the whole bridge sits in a 16 pin QFN at 0.4 Ω typical.

Order code and package

Ordering stringDRV8801RTYR
Family documentDRV8800 and DRV8801, SLVS855K, revised March 2021
PackageQFN (RTY), 16 pins, with an exposed pad
Reel and packing3000 pieces on a large reel, NiPdAu lead finish
Moisture levelLevel 3, 260 C peak, 168 hours of floor life
Body markingDRV8801
Temperature rangeminus 40 to plus 85 degrees
Carrier tape330 mm reel, 12.4 mm width, 4.25 mm cavity
HTSSOP siblingDRV8801PWPR in the PWP body, 2000 pieces on a reel, same die
InterfacePHASE and ENABLE, no PWM pair
Current feedbackVPROPI output, five times the sense voltage, DRV8801 only
Difference from DRV8800The DRV8800 has no VPROPI pin and no sense resistor path

Electrical parameters that decide the application

Supply range8 to 36 V
Peak output currentPlus or minus 2.8 A
Bridge resistance0.48 Ω source and 0.35 Ω sink at 2.8 A and 25 C, about 0.4 Ω for the pair
Sense trip voltage500 mV typical across the sense resistor
Sense resistor example0.2 Ω in the vendor table, which gives about 2.5 A of trip
Current output gainVPROPI equals five times the sense voltage
Overcurrent trip3 A with a deglitch and a retry
Undervoltage6.5 V rising and 7.5 V typical on the supply
Sleep currentAbout 2 uA
Charge pumpInternal, with a 0.1 uF flying capacitor
Thermal warning160 C, the part stays in warning until the die cools
Thermal shutdown175 C
Propagation delay5 us typical for a direction change

Family variants and how they differ

DRV8801PWPRThe HTSSOP body, 2000 pieces on a large reel, the same function
DRV8800RTYRNo current output and no sense path, for a load that does not need feedback
DRV8800PWPRThe same part in HTSSOP
DRV8801RTYRG4Green material declaration on the same QFN reel
DRV8801RTYTSmall reel for prototypes, which the current addendum lists as active in this body
DRV8803 and DRV8804Four channel low side drivers in the same family for unipolar loads
VPROPI behaviourFalls to 0 V while the bridge is in slow decay recirculation

Points to check before this part goes on a BOM

The sense resistor does two jobs on this part and they have to be sized together. The trip point is set by the 500 mV threshold across the resistor, so 0.2 Ω gives about 2.5 A, and the same voltage is multiplied by five on the VPROPI pin, so the analog output swings 2.5 V at that current. A larger resistor gives a lower trip and a larger signal, and a smaller one the opposite, which is the whole trade in one component.

VPROPI drops to zero whenever the bridge enters slow decay, because the current is then circulating through the low side FETs and not through the sense resistor. A controller that samples the current output during the off portion of a PWM cycle reads zero and concludes the motor has stopped. The sample has to be taken while the bridge is driving, or the firmware has to know the decay pattern and time the conversion.

The device is rated to 85 degrees ambient, not to the 125 degrees that most of the motor drivers in this catalogue carry. A 36 V bridge in a sealed enclosure with a small heatsink area will reach that limit long before the current limit is reached, and the 160 C thermal warning is a die temperature, not an ambient one. The HTSSOP sibling has more copper area to work with, but the same silicon limit.

The PHASE and ENABLE interface sets the behaviour of a PWM command in a way that firmware has to know. Toggling ENABLE produces a fast decay through the bridge, while toggling PHASE produces a slow decay through the low side FETs, and the current ripple and the acoustic noise differ between the two. The 5 us propagation delay is small compared with a 20 kHz carrier, so neither method is limited by the part.

The charge pump requires its two capacitors and they are not optional. A 0.1 uF flying capacitor between CP1 and CP2 and a 0.1 uF reservoir between VCP and the supply are part of the circuit, and omitting the reservoir leaves the high side gate drive with only the flying capacitor to work from. That shows up as a bridge that works at low duty and fails at high duty, which is a difficult symptom to trace back to a missing part.

Driving a stepper winding with one bridge

One winding of a bipolar stepper is the natural load for a full bridge of this size, and the current feedback turns the bridge into a chopper. The controller reads VPROPI, compares it with a reference and gates ENABLE, which is a current loop built from the part and the firmware rather than from a dedicated regulator. At 2.8 A peak and 0.4 Ω the bridge drops about 1.1 V, so a 24 V supply leaves plenty of headroom for the winding to reach its current quickly.

The slow decay of a PHASE toggle matters for a stepper, because it keeps the current circulating in the winding instead of returning it to the supply. That is what allows a microstepping waveform to hold its shape at moderate step rates, and it is also why the VPROPI reading disappears during that portion of the cycle.

Where the current output replaces an amplifier

A printer, a vending mechanism or an industrial actuator often needs to know whether the load has hit an end stop. With VPROPI on the board, that question is answered by comparing the analog output with a threshold, and no current sense amplifier, no shunt kelvin connection and no separate reference are needed. The five to one gain is fixed, so the threshold is set once in the firmware for a given sense resistor.

The limit of that approach is accuracy at low current. VPROPI is an analog multiplication of a small sense voltage, and near zero the offset of the amplifier dominates. A stall detector that has to work at 10 per cent of rated current needs a larger sense resistor, which lowers the trip point, so the two requirements pull against each other.

Where this order code fits

The part is chosen where one brushed motor or one stepper winding has to be driven from a 12 V or 24 V rail and the controller wants an analog current reading without adding an amplifier. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What sense resistor should be used? The trip point is 500 mV divided by the resistance, so 0.2 Ω gives about 2.5 A and 0.1 Ω about 5 A, which is above the 2.8 A rating. The resistor also sets the VPROPI swing at five times its voltage, so the two limits are chosen together with the ADC range in mind.

Why does the current reading fall to zero during PWM off time? The sense resistor sits in the low side path, and in slow decay the current circulates through the low side FETs without passing through it. The reading is valid only while the bridge is driving, so the conversion has to be timed to the on portion.

Is this part automotive grade? No. The whole DRV880x family is rated minus 40 to plus 85 degrees and the document carries no AEC-Q100 qualification. An automotive mechanism needs a different part number with its own qualification.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.