Contact Us

DRV8701PRGER

Brand: Texas Instruments
Texas Instruments DRV8701PRGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8701PRGER — Power Management & Signal Chain | Superb Automation

DRV8701PRGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8701PRGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8701PRGER: Brushed DC full bridge gate driver with a PWM interface in a 4 mm QFN

DRV8701PRGER is a single H bridge gate driver in the 24 pin RGE body that drives four external N channel MOSFETs from 5.9 V to 45 V, sets its gate current in five steps from 6 mA to 150 mA source and 12.5 mA to 300 mA sink, and regulates winding current with fixed off time chopping in a VQFN-24 body of 24 pins. The DRV8701 is a full bridge gate driver for a brushed DC motor, with a PWM interface on the P variant and a phase and enable interface on the E variant. It drives four external N channel devices with a 9.5 V gate drive, holds 100 percent duty cycle, and includes a 20 V per V current sense amplifier plus an internal current regulation loop with a fixed off time. Two internal regulators provide 4.8 V and 3.3 V at up to 30 mA each for the rest of the board, and a sleep mode holds 9 uA.

Order code and package

Order codeDRV8701PRGER
Bridgesingle H bridge, four external N channel MOSFETs
Operating voltage5.9 V to 45 V
InterfacePWM on the P variant, phase and enable on the E variant
Gate drive voltage9.5 V
Source current6 mA to 150 mA in five steps
Sink current12.5 mA to 300 mA in five steps
Current sense amplifier20 V per V
RegulatorsAVDD 4.8 V at 30 mA, DVDD 3.3 V at 30 mA
Package24 pin VQFN with exposed pad, 4 mm by 4 mm by 0.9 mm

Electrical parameters that decide the application

Duty cycle support100 percent
Sleep current9 uA
Current regulationfixed off time chopping, limits inrush and stall current
Logic levels1.8 V, 3.3 V and 5 V
Protectionsundervoltage lockout, charge pump undervoltage, overcurrent, pre driver fault, thermal shutdown
Fault outputnFAULT pin
Gate current settingsingle resistor on the IDRIVE pin
Sense amplifier gain20 V per V fixed
External component countfour FETs, one sense resistor, one gate current resistor

Points to check before this part goes on a BOM

The five gate current settings are the whole tuning range of this part, and the resistor on the IDRIVE pin selects all of them at once for both edges. Because the sink range is twice the source range in each step, the same setting gives a stronger turn off than turn on, which suits a bridge driving an inductive load: the faster the current commutates, the less time the body diodes spend conducting. A 300 mA sink into a 50 nC gate is 167 ns to the plateau, and a 12.5 mA sink is 4 us, so the range spans a factor of 24 in edge time and a factor of 24 in the frequency content of the switching noise.

The internal current regulation with a fixed off time is a hardware current limit that works without firmware. When the voltage across the sense resistor exceeds the reference, the bridge turns off for a fixed interval, then turns back on. The result is a chopping frequency that depends on the inductance and the supply, so it is not a constant frequency and it is not silent. In a motor that has a low inductance and a high supply the chopping frequency can reach the audible band, which is why the sense resistor value and the off time have to be chosen for the motor rather than for the worst case current alone.

Nine point five volts of gate drive is a fixed number and it interacts with the choice of external device. A standard level MOSFET with a 10 V on resistance specification is fully enhanced at 9.5 V in a warm condition and slightly above its specified resistance when cold, which is the opposite of what a thermal calculation usually assumes. A logic level device with a 4.5 V specification has more margin at 9.5 V. The gate drive is not adjustable, so the external device has to be chosen to match it rather than the other way round.

The two internal regulators are 4.8 V and 3.3 V at 30 mA each, and they are fed from the motor supply through the same junction as the gate drive. That makes them convenient and it makes their current part of the thermal budget: at a 45 V supply and 30 mA on both, the regulators alone dissipate 2.5 W. In practice the load is a microcontroller at a few milliamps, so the loss is tens of milliwatts, but the number to check is the short circuit case where a regulator is asked for its full current at the top of the supply range.

The 45 V maximum supply is the constraint that separates this part from the 60 V family members. A 36 V battery pack at full charge is 42 V and inside the rating, and a 48 V rail is not. A 24 V industrial supply with a 20 percent transient is 29 V and has margin, while a 36 V supply with the same transient is 43 V and has almost none. The transient rating and the operating rating are the same number on this device, so the supply has to be clamped rather than the part chosen with margin.

A 4 mm by 4 mm QFN with four external FETs means the thermal path of the driver is through its pad and the thermal path of the power stage is through the FETs, and the two are independent. The driver's own loss is the gate charge times the gate voltage times the frequency, which at 20 kHz and 50 nC is 9.5 mW per device, small enough that the pad is about the ground return rather than about heat. That is what allows the part to be this small, and it is why the routing guidance concentrates on the gate loop and the sense resistor rather than on copper area.

The sense amplifier has a fixed gain of 20, so the sense resistor is chosen against the converter range rather than against the amplifier. With a 3.3 V converter and a 1.65 V offset the usable swing is 1.65 V, which at a gain of 20 is 82 mV across the resistor. On a 5 A motor that is 16 milliohm, and the loss at full current is 0.4 W. The same measurement on a 0.5 V reference from a dedicated amplifier could use a much smaller resistor, which is the trade between resolution and loss that a fixed gain forces.

Where this order code fits

This order code belongs on brushed DC motor drives in power tools, handheld vacuum cleaners, industrial pumps and valves, home automation actuators and robotics, where an H bridge has to be built from external devices chosen for the current and the thermal path. It is also the part chosen where the controller has a PWM peripheral and no current loop, because the internal regulation limits the winding current during a stall or a start up without any firmware intervention. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What is the difference between the P and the E variant? The P variant takes a PWM input and derives the bridge state from the duty cycle, which suits a controller with a PWM peripheral. The E variant takes phase and enable inputs, which suits a controller that wants to command direction and magnitude separately. The silicon is the same and the pinout is the same, so the choice is about the controller interface.

Does the current regulation work without firmware? Yes. The loop compares the sense voltage against a reference and chops with a fixed off time when the threshold is exceeded, so a stalled motor is held at the set current with no software involvement. The chopping frequency depends on the motor inductance and the supply, so the audible noise of the drive is a function of the motor rather than of the driver.

How is the gate current chosen? A single resistor on the IDRIVE pin selects one of five source and sink settings. The sink setting is always stronger than the source setting in the same step, which is deliberate for an inductive load. The choice is a balance between switching loss, which wants a fast edge, and radiated noise, which wants a slow one.

Can it run from a 48 V rail? No. The operating maximum is 45 V and the same number applies to transients. A 36 V pack at full charge sits at 42 V, which is inside. A 48 V rail needs a different part, and a 36 V rail with significant inductive transients needs a clamp rather than a part chosen at the limit.

SUPERB holds and sources this driver line against the exact order code, with the reel, date code and country of origin stated on the offer. When a stage has to move to a second part, the Component Lead Time Solutions page sets out the checks that separate a working substitute from one that fails on the bench.