DRV8436RGER
Product Specifications
DRV8436RGER
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8436RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8436RGER: 48 V and 1.5 A without a serial bus
The DRV8436RGER is the 4 mm QFN body of the DRV8436, a bipolar stepper driver that keeps the hardware interface of the simpler members of the family while raising the rail to 48 V. It carries two H-bridges, a 1/256 microstepping indexer and internal current sense, so the two external sense resistors are removed, and the vendor publishes plus or minus 7.5 percent full scale current accuracy for that arrangement.
The supply is 4.5 V to 48 V operating with 50 V absolute maximum. On resistance is 900 mOhm high side plus low side at 24 V and 25 C, and the vendor quotes three current figures that do not agree at first reading: 2.5 A peak in the parametric table, then 2.4 A peak, 1.5 A full scale and 1.1 A rms in the feature list. The feature list is the one to carry into a thermal calculation, because the parametric table describes the package limit and the feature list describes the driver with a real board under it.
The interface is STEP and DIR plus a set of configuration pins, so the step mode and the decay mode are chosen by tying pins high or low rather than by writing registers. Decay options are smart tune, mixed and fixed slow, and off time is selectable at 7, 16, 24 or 32 microseconds. Sleep current is 2 microamps and the logic inputs accept 1.8 V, 3.3 V and 5 V levels.
What it does not have is the SPI port, the stall detection and the open load detection of the S version. That is the whole trade: the same die family and the same 4 mm footprint, minus the diagnostics, for a lower price and a shorter start up because there is no register map to load. A mechanism that finds its end stop with a switch does not need the extra function.
Key data for the DRV8436RGER
| Operating supply | 4.5 V to 48 V, absolute maximum 50 V |
| Current | 1.5 A full scale, 1.1 A rms, 2.4 A peak per bridge |
| Parametric peak | 2.5 A in the vendor parameter table, package limit rather than a board figure |
| On resistance | 900 mOhm high side plus low side at 24 V and 25 C |
| Interface | STEP and DIR with pin strap configuration, no serial bus |
| Microstepping | Up to 1/256 |
| Current sense | Internal, plus or minus 7.5 percent full scale, no sense resistors |
| Decay | Smart tune, mixed and fixed slow, off time 7, 16, 24 or 32 microseconds |
| Sleep current | 2 microamps typical |
| Temperature | Minus 40 C to plus 125 C operating |
Body, packing and marking data
| Body in this code | 16-pin VQFN, the RGE outline, 4.00 mm by 4.00 mm, 16 mm squared |
| Other body | 16-pin HTSSOP, the PWP outline, 9.70 mm by 6.40 mm, 62 mm squared |
| Carrier | Tape and reel; the count per reel is read from the vendor addendum row for this order code |
Reading the code before you buy it
DRV8436 is the circuit, RGE is the 4 mm QFN and the trailing R is the reel. The S version of the family is a separate circuit with the serial port, so a drawing that says DRV8436 and a reel that says DRV8434S are not the same part even though both sit in the same footprint at the same pin count. The difference shows up as an unresponsive SPI bus on a board that expects one, or as a set of configuration pins that do nothing on a board that expects the other.
The vendor positions this part in the middle of a ladder that goes from DRV8428 at 1500 mOhm and 1 A to DRV8434S at 330 mOhm and 2.5 A, all in 16 pins, and then to the 24 and 28 pin bodies for 3 A and 5 A. That ladder is worth keeping in the sourcing file, because a shortage on one rung is usually covered by the rung above at the cost of a decay option or a fault pin. Our pin to pin cross reference page is where we keep that comparison for the parts we carry.
On packing, the QFN reels in this family are quoted per order code and the trailing letter does not change with the reel size. We confirm the count from the addendum row before quoting, because a 4 mm QFN reel and a 9.7 mm HTSSOP reel are not the same length on the line.
Where the DRV8436RGER fits
Office automation is the natural home: printers, scanners, document feeders and card handling mechanisms run 24 V steppers at 0.5 A to 1 A per phase, and they want a driver that starts moving the moment the enable pin goes high without a bus transaction first. The 48 V rating matters there because the same board is often sold into regions where the 24 V supply is not well regulated.
Vending machines, ticket dispensers and locker mechanisms use the same part for the same reason, and they also use the 2 microamp sleep current because the machine is idle most of the day. Laboratory instruments and medical sample handlers use it where the axis count is small and a star wired STEP and DIR from the controller is simpler than a shared bus.
Where it does not fit is a mechanism that needs to know it has stalled without a switch, or an instrument that has to report an open winding as a fault. Those two functions live in the S version, and moving to it is a same footprint change with a new bus. Our medical device components page covers the qualification paperwork that comes with that change on a medical build.
Questions we get on this code
Which current figure do I use for the thermal calculation? Use 1.1 A rms and 900 mOhm, which gives about 0.44 W per bridge at full step and about 0.88 W for both phases. The 1.5 A full scale figure is the peak of the sine wave, and a thermal budget built on that number overstates the loss by a factor of two.
Can the 48 V part replace the 33 V part on an existing board? On the same 16-pin footprint yes, and the current rating goes up. What changes is the current accuracy figure, from plus or minus 6 percent to plus or minus 7.5 percent, so a dose or position tolerance that was calculated on the tighter number has to be recalculated. That is the check we run before approving the swap.
Does it need a charge pump capacitor? The charge pump is internal and the capacitors are integrated on this family, so no external flying capacitor is needed. What the board does need is a bulk capacitor on VM close to the pin and a ceramic bypass on the logic supply, because the current regulation loop draws its pulses from that bulk capacitor.
Is the part available in a body that can be hand soldered? Yes, the PWP HTSSOP at 9.7 mm by 6.4 mm with 0.65 mm pitch. That body is the one to use for prototypes and for low volume builds where a 4 mm QFN reflow profile is a problem.