Contact Us

DRV8343HPHPRQ1

Brand: Texas Instruments
Texas Instruments DRV8343HPHPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8343HPHPRQ1 — Power Management & Signal Chain | Superb Automation

DRV8343HPHPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8343HPHPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8343HPHPRQ1: automotive three phase gate driver with three integrated current sense amplifiers

DRV8343HPHPRQ1 is a three phase gate driver unit for N-channel power FETs in a HTQFP body of 48 pins. The part drives three high side and three low side N-channel FETs from a 5.5 V to 60 V supply, brings out a dedicated source and drain pin for every half bridge so a leg can drive a solenoid instead of a motor phase, and carries three low side current sense amplifiers with selectable gains of 5, 10, 20 and 40.

Order code and package

Order codeDRV8343HPHPRQ1
PackageHTQFP, 48 pins, 7.00 mm by 7.00 mm, exposed pad
Supply voltage5.5 V to 60 V
Power FETs3 high side and 3 low side N-channel, external
Interfacehardware, pin and resistor configured
QualificationAEC-Q100 grade 1, minus 40 to plus 125 degrees ambient
Auxiliary rail3.3 V linear regulator, 30 mA
Current sense amplifiersthree, low side
Gate drivecharge pump for 100 percent duty cycle

Electrical parameters that decide the application

Peak source current1 A
Peak sink current2 A
Sense amplifier gain5, 10, 20 or 40 volts per volt
Sense modebidirectional or unidirectional
VDS trip point7 levels, set by resistor
PWM modes6x, 3x, 1x and independent
Logic levels3.3 V and 5 V compatible
Slew rateadjustable by pin

Points to check before this part goes on a BOM

One amp of source current into a 100 nanocoulomb gate is 100 ns of rise time, so the gate drive rating is about switching speed and hardly about average current. The average draw is 100 nanocoulomb times the switching frequency per FET, which at 20 kHz and six FETs is 12 mA, a figure the charge pump supplies without help.

The gate charge costs energy as well: 100 nanocoulomb at a 12 V gate is 1.2 microjoule per switching event per FET, and six FETs at 20 kHz is 144 mW dissipated in the driver and the gate resistors. That is the number that decides whether a 7 mm body with an exposed pad runs cool in a 105 degree enclosure.

The 60 V supply rating is a gate driver rating, not a system rating. A 24 V automotive rail carries load dump transients far above 60 V, so a clamp in front of the part is part of the circuit and not an optional protection; the same applies at the low end, where a 12 V battery cranking to 6 V is only 0.5 V above the 5.5 V floor.

The H in the order code means the hardware interface: the VDS trip level, the gain and the drive strength are set by resistors on pins and fixed when the board is built. Changing a trip point on this part is a resistor change, while the S variant of the same device takes the same settings over SPI at run time.

The VDS trip point has seven levels and works on the drain to source voltage of the FET, so there is no shunt in the power path. The trip level has to sit above the FET's on resistance drop at the highest current and the highest temperature, and on resistance rises by roughly half again from 25 to 125 degrees, which is the margin the seven levels have to cover.

Three low side sense amplifiers with gains up to 40 mean phase current is measured without a dedicated amplifier per phase. Low side sensing keeps the common mode at ground, so the gain can be high, but the measurement is only valid while the low side FET is on, which ties the sampling window to the PWM duty cycle.

The charge pump holds the high side FET on indefinitely, which is what allows a half bridge to hold a solenoid energised at 100 percent duty. Gate drivers that rely on a bootstrap capacitor cannot do that, and the difference shows up as a solenoid that buzzes or drops out when the command is held.

The 3.3 V regulator inside is rated 30 mA, enough for a small MCU or a hall sensor set and not enough for a radio. Anything above that budget needs its own regulator, and the internal one still has to be kept within its dissipation limit at the highest supply voltage, where 60 V in and 3.3 V out at 30 mA is 1.7 W inside the package.

The adjustable drive strength is an emission decision as much as a switching loss decision. A slow gate turn on reduces the high frequency content that has to be filtered, and a fast one reduces the time the FET spends between off and on. The setting that passes the automotive emission test is usually not the one that minimises loss, so the two are traded on the bench.

The 6x, 3x, 1x and independent PWM modes let the part work with a timer that has three, six or no complementary outputs. A microcontroller with a single three phase timer drives the 6x mode directly, and one without complementary outputs falls back to the independent mode and does the dead time in software.

The charge pump output can drive a reverse battery protection FET in the supply line, which saves a separate charge pump for that job. The same pump holds the high side gate up at 100 percent duty, so the part keeps a solenoid energised without a bootstrap capacitor and without the periodic refresh a bootstrap circuit needs.

Where this order code fits

Automotive pumps, fans, seat and window motors, steering assist stages and any three phase or three solenoid load that needs AEC-Q100 grade 1 parts and low side current sensing. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

Can one leg drive a solenoid instead of a motor phase? Yes. Each half bridge has its own source and drain pin, so the three legs can be used independently for solenoids, and the PWM mode selection covers 6x, 3x, 1x and independent control.

Does it need external current shunts? Not for the current sense amplifiers, which measure the low side FET drain to source voltage. The VDS trip for protection works the same way, so the power path carries no shunt unless the product wants one for its own metering.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.