Contact Us

DRV8334PHPR

Brand: Texas Instruments
Texas Instruments DRV8334PHPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8334PHPR — Power Management & Signal Chain | Superb Automation

DRV8334PHPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8334PHPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8334PHPR: A 60 V Smart Gate Driver With 45 Drive Levels and a 1 mV Current Sense

DRV8334PHPR is a three phase gate driver with integrated current sense amplifiers and SPI in a HTQFP (PHP) body of 48 pins. It drives six N channel FETs from 4.5 V to 60 V, sets peak gate current in 45 steps up to 1 A source and 2 A sink, and holds the gate supply at 13.5 V from a charge pump that supplies up to 50 mA of average gate current. The three low side shunt amplifiers have a total offset under 1 mV across temperature and nine gain settings between 5 and 40, which is what removes the external current sense chain from a 400 nC bridge.

Order code and package

Ordering stringDRV8334PHPR, large reel, 1000 pieces
Family documentDRV8334, SLVSHC7B, revised September 2025
PackageHTQFP (PHP), 48 pins, 7.00 mm by 7.00 mm
Lead finishNIPDAU
Moisture levelLevel 3, 260 C, 168 hour floor life
Body markingDRV8334
Temperature rangeminus 40 to plus 125 degrees ambient
QFN alternativeDRV8334RGZR, 48 pins, 4000 piece reel, marking RGZ
InterfaceSPI for settings and diagnostics, plus six PWM input modes
Rows that differ only by suffixDRV8334PHPR.A at the same reel size

Electrical parameters that decide the application

Supply range4.5 to 60 V
Gate supply11.5 to 13.5 V from the charge pump, up to 50 mA average gate current
Peak gate current45 levels, up to 1000 mA source and 2000 mA sink
FET size supported400 nC of gate charge at 20 kHz
Current sense gainNine settings, 5, 10, 12, 16, 20, 23, 25, 30 and 40 V per V
Current sense offsetminus 0.65 to plus 0.65 mV total, including drift
Sleep current16 to 30 uA with the supply at 24 V
Active current25 to 40 mA at 24 V while switching, with no FETs connected
Undervoltage lockoutPVDD 4.65 V rising and 4.2 V falling, 450 mV of hysteresis
Gate supply lockout7.8 V rising, 7.6 V falling, 215 mV of hysteresis
Undervoltage warning6.0 or 7.3 V rising, selected by register
Logic thresholds0.8 V low, 2.1 V high, 200 to 450 mV of hysteresis
PWM modes6x, 3x, 1x and independent, selected by register
Protection inputsVDS monitors, shunt overcurrent monitors and VGS gate fault monitors

Family variants and how they differ

DRV8334 in HTQFP48 pins with a lead frame, the body on this page
DRV8334 in VQFNSame die, 48 pins, 4000 piece reel, smaller footprint
Against the DRV8300The 8300 is a plain driver, this part adds the current sense and the SPI
Against the DRV8323The 8323 has three shunt amplifiers and a buck, this part adds gate fault monitoring and 45 drive levels
Charge pumpA trickle path holds the gate supply at 100% duty, which the bootstrap family cannot do
MonitoringPhase feedback comparators, supply monitors and a thermal warning

Points to check before this part goes on a BOM

The 45 drive levels are the difference between a driver that works and a driver that passes an emissions test. Peak current sets the switching edge, the edge sets the radiated spectrum, and a fixed 1 A driver forces the board to add gate resistors to slow it down. Here the level is a register value, so the same board can be tuned in firmware from a 20 ns edge for efficiency to a 200 ns edge for the chamber, and the vendor provides a three step dynamic control so the turn off can be faster than the turn on.

The current sense offset of 0.65 mV is the number that matters at low current. With a 1 mOhm shunt and a gain of 40, 10 A produces 400 mV, and 0.65 mV of offset is 0.16 percent of that. At 1 A the same offset is 1.6 percent, which is still better than a discrete amplifier with a 5 mV offset. The nine gain steps exist so the sense resistor can be chosen for the highest current in the application rather than for the smallest.

The trickle charge pump is what allows 100% duty. A bootstrap capacitor refreshes only while the low side FET is on, so a bridge that holds the high side on for a full period loses gate voltage and the FET drifts into its linear region. This part generates the gate supply from a charge pump that runs continuously, so the high side can stay on indefinitely, and the same supply can feed an external protection circuit through the overdrive path.

SPI is not optional on this part in the way it is on a register light driver. The PWM mode, the drive levels, the sense gain, the overcurrent thresholds and the fault responses all live in registers, and the default values are a starting point rather than a working configuration. A board that brings the bus out to a header and configures the part once at start up is fine; a board that leaves the pins floating gets a driver in whatever mode the defaults define.

Where the monitoring earns its cost

A gate fault monitor watches the gate voltage of each FET and reports a shorted or open gate before the bridge fails. On a 60 V tool with 400 nC FETs a single shorted gate turns a stalled motor into a shoot through, and the difference between a reported fault and a destroyed board is one register bit. The VDS monitors do the same for a shorted FET, and the shunt monitors catch an overcurrent that the VDS path would only see after the FET has already been stressed.

The phase feedback comparators are for sensorless control. They report the phase voltage against a reference so the controller can estimate the rotor position without an external comparator network, which removes three resistors and three pins from every board that runs a sensorless brushless motor at speed.

The shunt value is chosen from the highest current the loop has to resolve, not from the amplifier gain that looks best on a bench. A 1 mOhm shunt at 20 A produces 20 mV, and the 0.65 mV of offset is 3 percent of that, while a 0.5 mOhm shunt halves the loss and doubles the error. The nine gain steps exist so that a 200 A tool and a 5 A pump can share one board, and the chosen gain is the one that puts the full scale current near the top of the amplifier range rather than near the bottom.

Where this order code fits

Bridges above 24 V that need current sense without a discrete amplifier start from the power management cross reference page Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the part run from 48 V directly? Yes, the supply range ends at 60 V and the gate supply is generated from the same rail. The charge pump holds 13.5 V while the rail moves, and the undervoltage lockout at 4.65 V protects the FETs during a brownout rather than letting them run at partial enhancement.

How is the overcurrent threshold set? Two paths. The VDS monitor compares the drain to source voltage of each FET against a register value, and the shunt monitor compares the amplifier output with a reference. Both are configured over SPI and both can be set to latch, retry or report only.

What is the minimum gate charge for stability? There is no minimum, but the drive level has to be matched to the FET. A 100 nC FET driven at the 2 A setting switches in a few nanoseconds, which produces ringing on a long gate loop, so the level is chosen from the loop inductance and the allowed edge rate rather than from the largest setting available.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.