DRV8313PWPR
Product Specifications
DRV8313PWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8313PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8313PWPR: Three Half Bridges With a Comparator Left Over for Current Limit
DRV8313PWPR is a triple half bridge driver for three phase brushless motors in a HTSSOP (PWP) body of 28 pins. It drives a three phase brushless motor from 8 V to 60 V at 2.5 A peak per half bridge, gives each half bridge its own ground pin so that three shunt resistors can be used, and leaves one uncommitted comparator free for a current limit or a fault threshold.
Order code and package
| Ordering string | DRV8313PWPR |
| Family | DRV8313 triple half bridge, document SLVSBA5D |
| Package | HTSSOP with thermal pad, PWP body, 28 pins, 9.70 mm by 4.40 mm nominal |
| Second package | VQFN RHH body, 36 pins, 6.00 mm by 6.00 mm, as DRV8313RHHR |
| Reel and packing | 2000 pieces on a large reel for the PWP body, 2500 for the RHH body |
| Moisture level | Level 3, 260 C peak, 168 hour floor life |
| Part marking | DRV8313 |
| Tube rows | 50 pieces for the PWP body and 60 for the RHH body |
| Operating supply | 8 V to 60 V |
| Output rating | 2.5 A peak per half bridge, with a 3.5 A short circuit trip mentioned in the block diagram |
| Auxiliary regulator | 3.3 V at 10 mA, usable as the comparator reference |
Electrical parameters that decide the application
| High side on resistance | 0.24 ohm typical at 25 C and 0.29 ohm at 85 C at 24 V and 1 A |
| Low side on resistance | 0.24 ohm typical at 25 C and 0.29 ohm at 85 C at 24 V and 1 A |
| Ground arrangement | One ground pin per half bridge, so each leg can carry its own shunt |
| Comparator | Uncommitted, open drain output, needs an external pull up |
| Comparator response | Quoted for a 100 mV step with 10 mV of overdrive |
| Charge pump | Two external capacitors, and it stops when the sleep pin is low |
| Under voltage lockout | On the motor supply, reported on the fault pin |
| Fault reporting | Open drain fault pin, low on overcurrent, over temperature, under voltage or a charge pump fault |
| Control interface | Three inputs plus three enables, all with internal pulldowns |
| Sleep mode | A low on the sleep pin stops the bridges and the charge pump |
| Thermal path | The PowerPAD has to be soldered down, the current figures assume it |
| PWM frequency | Set by the controller, there is no internal oscillator to program |
Family variants and how they differ
| DRV8313RHHR | The same die in the 36 pin VQFN body at 2500 pieces on a large reel |
| DRV8313PWP | The 50 piece tube row of the PWP body |
| DRV8844 | Four half bridges when a fourth leg or a second axis is needed |
| DRV8306 | A gate driver for external MOSFETs when 2.5 A is not enough for the motor |
| DRV8412 | Two full bridges at 3 A continuous for a brushed motor with more current |
| DRV10987 | An integrated three phase driver with sensorless commutation when the controller should not generate the sequence |
Points to check before this part goes on a BOM
The three ground pins are the reason to choose this part over a quad. Each half bridge returns through its own pin, so a shunt on each leg measures that leg current without summing the other two, which is what a three shunt current sense scheme needs. A board that ties the three grounds together at the package loses that and can only measure the sum.
The comparator is uncommitted, which means it has no connection to the bridges at all. It can compare a shunt voltage against the 3.3 V regulator divided down, or it can watch a supply rail, and the output is open drain so it needs a pull up to the logic rail. The response is specified for a small overdrive, so a comparator used as a fast current limit has to be tested at the actual overdrive on the board.
Sleep mode turns off the charge pump along with the bridges. That is what makes the sleep current low, and it also means the part needs a start up delay after the sleep pin goes high before the high side gates can be driven. A controller that starts switching in the same microsecond as it releases sleep will see the first pulses dropped.
The 2.5 A figure is a peak rating per half bridge and the continuous current is thermal. At 0.24 ohm and 2 A the conduction loss alone is about 1 W per bridge, and three bridges in a 28 pin body with a thermal pad on a small copper area will reach the 150 C shutdown before the current limit is reached.
There is no internal current limit loop, only the overcurrent trip. The trip turns the bridge off and reports a fault, so a motor that stalls draws the trip current for the deglitch time and then stops rather than regulating. Systems that need a regulated current limit have to build it from the comparator and the controller.
A three phase stage with three shunts
Three ground pins and three enables make this a natural fit for a low side shunt on every leg. The controller samples each shunt during the low side conduction window, reconstructs the three phase currents and closes the loop, and the driver does nothing more than follow the six step pattern it is given. That keeps the commutation algorithm where it belongs, in the controller, and keeps the driver simple enough to qualify.
The alternative is a single shunt in the return path, which needs only one amplifier but gives the sum of the three currents. That works for a sinusoidal drive with a known modulation pattern and fails when the phases are not balanced, which is exactly the case during a fault. Boards that need to detect an unbalanced winding end up with the three shunt arrangement.
Where 2.5 A is the right size
Camera gimbals, small pumps, fan trays and HVAC damper motors all sit in the range where a 2.5 A peak bridge is enough and an external MOSFET stage is overkill. The part brings the gate drive, the charge pump and the protection on one die, so the board carries three shunts, three decoupling capacitors and the thermal pad and nothing else.
Above that range the dissipation in the integrated FETs is the limit. A 5 A motor at 0.24 ohm dissipates 6 W in the bridges before switching losses, which no 28 pin package can pass to the board without a heatsink. That is the point where a gate driver with external MOSFETs becomes the cheaper answer, not because the silicon is better but because the heat has somewhere to go.
Where this order code fits
The part is used for a small three phase brushless motor, typically a gimbal, a pump or a fan, where the controller generates the commutation and the driver has to report faults. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Drone UAV Components page.
Questions buyers ask
Can the three grounds be tied together on the board? They can, and you lose the ability to sense each leg separately. The pins exist so that each half bridge can return through its own shunt, and tying them at the package turns three independent measurements into one summed measurement.
Is the comparator fast enough to act as a current limit? It is specified for a small overdrive, so the answer depends on the signal. At 10 mV of overdrive it responds in the time printed in the table, and a real shunt signal crosses that region quickly during a fault. The comparator only signals the event, the controller still has to turn the bridge off, so the loop delay is mostly in the controller.
What is the difference between the PWP and the RHH string? The package. PWP is the 28 pin HTSSOP at 2000 pieces on a large reel and 50 in a tube, RHH is the 36 pin VQFN at 2500 on a large reel and 60 in a tube. The die and the ratings are the same, so the choice is about board space and thermal path.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.