Contact Us

DRV8306HRSMR

Brand: Texas Instruments
Texas Instruments DRV8306HRSMR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8306HRSMR — Power Management & Signal Chain | Superb Automation

DRV8306HRSMR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8306HRSMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8306HRSMR: Three Gate Drivers and Three Hall Comparators for a Sensor Commutated BLDC

DRV8306HRSMR is a three phase brushless motor gate driver in a VQFN (RSM) body of 32 pins. It drives six external N-channel MOSFETs from 6 V to 38 V, generates the high side supply with a doubler charge pump referenced to the motor rail, and does the 120 degree trapezoidal commutation itself from three Hall inputs, so the controller only has to set a duty cycle and a direction.

Order code and package

Ordering stringDRV8306HRSMR
FamilyDRV8306 brushless gate driver, document SLVSE38A
PackageVQFN, RSM body, 32 pins, 4.00 mm by 4.00 mm nominal
Reel and packing3000 pieces on a large reel, and 250 on a small reel as DRV8306HRSMT
Moisture levelLevel 1, 260 C peak, unlimited floor life
Part markingDRV 8306H
Supply range6 V to 38 V operating, 40 V absolute maximum
Gate drive current150 mA source and 300 mA sink peak, 15 mA RMS average
Internal regulatorsA charge pump at VM plus 10 V for the high side, a 10 V linear regulator for the low side and a 3.3 V 30 mA regulator for external logic
Logic levels1.8 V, 3.3 V and 5 V inputs are all supported
Control pinsPWM, direction, brake and enable, plus a tacho output

Electrical parameters that decide the application

Commutation120 degree trapezoidal, generated internally from three Hall comparator inputs
Duty controlThe PWM pin sets the phase voltage duty, and 100 percent duty is supported
Hall comparatorsThree, with a deglitch time on the inputs so a noisy Hall edge does not commutate
Tacho outputA frequency output proportional to the commutation rate, for a speed loop
Gate drive adjustmentThe drive current is set by a resistor on the drive current pin, in steps
Overcurrent thresholdSet by a resistor on the voltage sense pin, with one of several fixed levels
Dead timeInserted automatically from the gate voltage monitors, plus a fixed digital dead time
Current limitA cycle by cycle limit from the sense resistor with a blanking time at the start of each PWM cycle
Protection setUnder voltage, charge pump under voltage, MOSFET overcurrent, gate driver fault and thermal shutdown
Brake behaviourThe brake pin turns all three low side devices on, which shorts the windings
Sleep modeA low quiescent state that stops the charge pump and the gate drive
BootstrapThe high side supply comes from the charge pump, so no bootstrap capacitor timing limit applies

Family variants and how they differ

DRV8306HRSMTThe 250 piece small reel row for a pilot build
DRV8305A similar three phase gate driver with a serial interface and more configurability
DRV8323A gate driver with integrated current sense amplifiers when shunt signals have to be amplified on board
DRV8313An integrated three phase driver at 2.5 A when external MOSFETs are not needed
DRV10987An integrated sensorless driver when there are no Hall sensors in the motor
DRV8844Four half bridges for a brushed motor or a stepper rather than a three phase load

Points to check before this part goes on a BOM

The charge pump is referenced to the motor supply, not to ground. It holds the high side gate drive 10 V above VM, which is why the part supports 100 percent duty and why there is no bootstrap capacitor to refresh. It also means the pump has to be able to supply the gate charge of the chosen MOSFETs at the chosen switching frequency, and a large die with a high gate charge can outrun a small pump at high frequency.

The commutation is fixed at 120 degrees trapezoidal and it comes from the Hall inputs. There is no sinusoidal mode and no sensorless mode, so the motor has to carry three Hall sensors and the controller cannot change the commutation angle. A motor without Halls needs a different part, and a motor that wants field weakening needs a controller that generates the sequence itself.

The drive current and the overcurrent threshold are set by resistors, not by firmware. That is the point of the hardware interface, and it also means a change of MOSFET or a change of motor requires a board change. Two resistors decide the switching speed and the fault threshold, and both have a direct effect on emissions and on how the bridge behaves during a short.

The dead time is derived from the gate voltage rather than from a fixed delay. The part watches the gate of each MOSFET and only allows the opposite device to turn on after the first one has actually discharged, which handles the variation between parts and over temperature. A fixed digital dead time is added on top, so the total is longer than either figure alone.

The brake pin shorts the windings through the low side devices. That stops the motor quickly and it also dumps the kinetic energy into the bridge and the motor, which can raise the rail through the body diodes if the supply cannot absorb it. A supply with a brake resistor or a clamp is normal on a mechanism with significant inertia.

A brushless pump or fan with three Hall sensors

A pump or a fan with three Hall sensors and a six device bridge is exactly the load this part was built for. The Hall signals go into the comparators, the part generates the six step pattern, and the controller sets a duty cycle with one PWM signal and a direction with one pin. The tacho output closes a speed loop without an encoder, which is often the whole control requirement on a fan tray.

The 6 V to 38 V range covers a 12 V and a 24 V rail with margin for the transient, and the 40 V absolute maximum leaves room for the regeneration spike a fan produces when it is braked. Above that range the part is outside its ratings, so a 48 V system needs a different driver rather than a clamp on this one.

What the automatic dead time is worth in production

Shoot through is the failure that kills a bridge in the first switching cycle, and it happens when the high and low devices conduct together for even a few tens of nanoseconds. A fixed dead time chosen for the worst case MOSFET slows every edge and costs efficiency, while a dead time chosen for the typical part risks cross conduction as the parts age and heat.

Watching the gate voltage removes that choice. The part waits until the gate has actually discharged before it enables the opposite device, so the dead time tracks the real behaviour of the MOSFET on the board. The fixed digital dead time on top is the guarantee for the case where the monitor is fooled, and both together are why this part can be qualified without a bench sweep over temperature.

Where this order code fits

The part is used where a three phase motor with Hall sensors has to be driven from a 12 V or 24 V rail and the controller should only set a duty cycle and a direction. Teams comparing it with a neighbouring part start from our Drone UAV Components page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does the part need Hall sensors? Yes. The commutation comes from three Hall comparator inputs, and there is no sensorless mode. A motor without Hall sensors needs a driver with a back EMF observer, which is a different part.

Can it run at 100 percent duty? Yes. The high side supply comes from a charge pump referenced to the motor rail rather than from a bootstrap capacitor, so there is no refresh window and no minimum off time. That is what makes full duty possible on a fan that runs at the rail voltage.

What sets the current limit? A sense resistor on the low side path and a resistor on the voltage sense pin choose one of the fixed thresholds. The limit acts every PWM cycle with a blanking time at the start of the cycle, so the switching spike does not trip it.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.