Contact Us

DRV8300DRGER

Brand: Texas Instruments
Texas Instruments DRV8300DRGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8300DRGER — Power Management & Signal Chain | Superb Automation

DRV8300DRGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8300DRGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8300DRGER: The QFN Body With an Adjustable Deadtime and a Polarity Pin

DRV8300DRGER is a three phase gate driver in a 4 mm QFN in a VQFN (RGE) body of 24 pins. It is the same 100 V three phase gate driver as the TSSOP member of the family, moved into a 4.00 mm by 4.00 mm QFN with two extra functions: a resistor from the DT pin sets the deadtime anywhere between 200 ns and 2000 ns, and the MODE pin chooses whether the low side inputs are inverted. Peak source current is 750 mA, peak sink is 1.5 A, and the bootstrap diode is inside.

Order code and package

Ordering stringDRV8300DRGER
Family documentDRV8300, SLVSFG5D, revised March 2022
PackageVQFN (RGE), 24 pins, 4.00 mm by 4.00 mm with an exposed pad
Reel and packing3000 pieces on a large reel, NiPdAu lead finish
Moisture levelLevel 1, 260 C peak, unlimited floor life
Body marking8300D
Temperature rangeminus 40 to plus 125 degrees
Bootstrap diodeIntegrated, the D letter in the order code
Deadtime controlDT pin, 200 ns to 2000 ns by resistor, 200 ns when left floating
Input polarityMODE pin, non inverted when floating, inverted when tied to GVDD
TSSOP siblingDRV8300DPWR, 20 pins, fixed 200 ns deadtime and no MODE pin
Logic compatibility3.3 V and 5 V inputs, 20 V absolute maximum

Electrical parameters that decide the application

Gate drive supply4.8 to 20 V on GVDD
Phase pin voltageUp to 100 V on SHx
Bootstrap absolute maximum125 V on BSTx and GHx
Negative transient on SHxMinus 22 V
Peak source current750 mA minimum
Peak sink current1.5 A minimum
Deadtime range200 ns to 2000 ns, linear with the DT resistor
Fixed deadtime200 ns typical when DT is left floating
Propagation delay150 ns typical and 250 ns maximum
Delay matching4 ns typical and 30 ns maximum
Standby current400 uA typical
GVDD undervoltageRising 4.6 V, falling 4.35 V
Bootstrap undervoltageRising 4.2 V typical, falling 4.0 V typical
Thermal pathExposed pad on a 4 mm body, which is the whole reason the QFN exists

Family variants and how they differ

DRV8300DRGERIntegrated diode, DT and MODE pins, QFN body, 3000 pieces on a reel
DRV8300NRGERThe same QFN without the bootstrap diode, for an external diode
DRV8300DPWRTSSOP body, fixed deadtime, no MODE pin, 3000 pieces on a reel
DRV8300DIPWRTSSOP body with inverted low side inputs
DRV8300NPWRTSSOP body, no diode, non inverted inputs
MODE floatingLow side input non inverted, the resonance of a new board is the same as the N letter part
MODE at GVDDLow side input inverted, which is what the D letter does on the TSSOP body

Points to check before this part goes on a BOM

The DT resistor is what the QFN buys, and the setting is linear from 200 ns at the top of the range to 2000 ns at the bottom. A bridge built from slow, high charge FETs needs the long end to avoid shoot through, and a bridge built from fast FETs needs the short end to avoid losing efficiency in body diode conduction. Leaving the pin floating gives the same 200 ns that the TSSOP body is fixed at, which is a useful fallback when the resistor is not fitted.

The MODE pin changes the polarity of all three low side inputs at run time, and it is sampled as a level rather than latched. Tying it to GVDD inverts the low side commands, leaving it open keeps them in phase. On the TSSOP body the same choice is made by the order code, so a board that moves between the two bodies has to keep track of which mechanism is doing the inverting.

The QFN body carries a Level 1 moisture rating and unlimited floor life, against Level 2 and one year on the TSSOP. That matters on a line that leaves reels out for long periods, and it matters for storage cost, because a Level 1 part does not need the dry pack routine that a Level 3 part does. The 4 mm body also puts the thermal pad closer to the FETs, which is where the heat actually goes.

Everything else is the same silicon: the same 100 V phase rating, the same minus 22 V negative transient tolerance, the same 750 mA source and 1.5 A sink, and the same two undervoltage protections with their different recovery rules. A bootstrap undervoltage still disables only that phase high side and waits for a new rising edge on its input, which is the behaviour that catches controllers out after a fault.

The 4 by 4 mm body with 24 pins at 0.5 mm pitch is at the edge of what a two layer board can route, and the exposed pad has to be soldered with vias into a copper area. A board that treats the pad as mechanical support runs the part hot, because the gate driver dissipates its switching loss in a very small area and has no other path to the board.

Choosing between this body and the TSSOP

The TSSOP 20 is easier to inspect and easier to rework, and it fixes the deadtime at 200 ns. The QFN 24 is smaller, has a better thermal path, carries a Level 1 moisture rating and lets the deadtime and the input polarity be set on the board. A high volume drive with a fast FET pair takes the QFN for the adjustable window, a low volume or a hand assembled prototype takes the TSSOP for the solder joint.

The pin count difference is real and it is not a drop in replacement in either direction. A board laid out for one body cannot take the other, so the choice is made at the first board revision, and a programme that expects to second source between the two has to allow for both footprints from the start.

Where a 100 V gate driver with 4 mm of board is used

A cordless tool, an e bike controller or a drone electronic speed controller puts the gate driver within a few millimetres of six power FETs, and at that distance the loop inductance of the gate trace matters more than the package style. The QFN with its pad on the same copper as the FET sources is the smaller loop, and the 4 ns of delay matching between phases is what keeps the three half bridges switching together at a 40 kHz carrier.

The negative transient rating of minus 22 V is the figure that survives a phase node ringing on a long motor cable. The absolute maximum on the bootstrap pin, 125 V, allows the high side to sit above the bus during that ring without damage, which is the margin that a 100 V bus actually needs.

Where this order code fits

The part fits a compact three phase inverter where the deadtime has to be tuned to the FET pair and the low side command polarity has to be chosen on the board rather than in the order code. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

How is the deadtime set? A resistor from DT to ground, linear from 200 ns at the top of the range to 2000 ns at the bottom. Leaving DT floating gives the 200 ns default, which is the same figure the TSSOP body is fixed at.

Can this replace the TSSOP part on an existing board? No. The pin count and the pin functions differ, because the QFN adds DT and MODE. The electrical behaviour is the same family, so the circuit around it is unchanged, but a new board is needed.

What does the MODE pin do? It sets the polarity of the low side inputs. Floating keeps them non inverted, tying it to GVDD inverts them. On the TSSOP body the same choice is baked into the order code by the D or N letter.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.