DRV8300DPWR
Product Specifications
DRV8300DPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8300DPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8300DPWR: Three Half Bridges for a 100 V Bus With the Bootstrap Diode Inside
DRV8300DPWR is a three phase gate driver for N channel MOSFETs in a TSSOP (PW) body of 20 pins. It drives six external N channel MOSFETs from a gate supply anywhere between 4.8 V and 20 V while the phase pins sit on a bus up to 100 V, and the D letter in the order code means the bootstrap diode is inside the package, so each high side needs only its capacitor. Peak source current is 750 mA, peak sink is 1.5 A, and this TSSOP body inserts a fixed 200 ns of deadtime with no pin to change it.
Order code and package
| Ordering string | DRV8300DPWR |
| Family document | DRV8300, SLVSFG5D, revised March 2022 |
| Package | TSSOP (PW), 20 pins, 6.40 mm by 4.40 mm |
| Reel and packing | 3000 pieces on a large reel, NiPdAu lead finish |
| Moisture level | Level 2, 260 C peak, one year floor life |
| Body marking | 8300D |
| Temperature range | minus 40 to plus 125 degrees |
| Bootstrap diode | Integrated on every D variant, including this one |
| Low side input polarity | Inverted with respect to INLx on the D letter, non inverted on the N letter |
| Deadtime in this body | Fixed 200 ns typical, no external setting |
| Sibling in the QFN body | DRV8300DRGER, 24 pin VQFN, 4.00 mm by 4.00 mm, adds DT and MODE pins |
| Logic compatibility | 3.3 V and 5 V inputs, 20 V absolute maximum on the input pins |
Electrical parameters that decide the application
| Gate drive supply | 4.8 to 20 V on GVDD, 20 V absolute maximum |
| Phase pin voltage | Up to 100 V on SHx in operation |
| Bootstrap absolute maximum | 125 V on BSTx and GHx, raised in revision D of the document |
| Negative transient on SHx | Minus 22 V |
| Peak source current | 750 mA minimum, 1200 mA maximum |
| Peak sink current | 1.5 A minimum, 2100 mA maximum |
| Propagation delay | 150 ns typical and 250 ns maximum from input to gate output |
| Delay matching | 4 ns typical and 30 ns maximum, phase to phase and within a phase |
| Rise and fall time | 24 ns typical and 50 ns maximum into 1000 pF |
| Standby supply current | 400 uA typical and 1.4 mA maximum with both inputs low |
| SHx leakage | 30 uA typical and 80 uA maximum with the bridge idle |
| GVDD undervoltage | Rising 4.6 V, falling 4.35 V, 310 mV of hysteresis, 10 us of deglitch |
| Bootstrap undervoltage | Rising 4.2 V typical, falling 4.0 V typical, 200 mV of hysteresis, 22 us of deglitch |
| Logic thresholds | 0.8 V maximum for a low and 2.0 V minimum for a high |
Family variants and how they differ
| DRV8300DIPWR | Integrated diode with inverted low side inputs, fixed deadtime, TSSOP body |
| DRV8300NPWR | No bootstrap diode, non inverted low side inputs, the external diode has to be added |
| DRV8300NIPWR | No diode and inverted inputs, the fourth combination in the same body |
| DRV8300DRGER | VQFN body with a DT pin for 200 to 2000 ns of deadtime and a MODE pin for input polarity |
| DRV8300NRGER | The same QFN body without the bootstrap diode |
| DRV8300-Q1 | The automotive grade version of the same function, documented separately |
| DRV8323 | A three phase driver that adds current sense amplifiers when shunt signal conditioning is wanted on chip |
Points to check before this part goes on a BOM
The bootstrap capacitor is the only high side component left on the D variants, and its droop budget is set by three numbers. The vendor example takes 12 V of GVDD, subtracts 0.85 V of diode drop at the quoted test current and 4.5 V of bootstrap undervoltage, leaving 6.65 V of allowed droop. A capacitor sized against a smaller droop simply holds the high side gate up longer before the 22 us undervoltage deglitch trips.
The high side cannot stay on forever at 100 per cent duty. The bootstrap capacitor is refreshed only while the phase node is pulled low by the low side FET or by the load, so a drive that commands a static high side for a long period will eventually cross the bootstrap undervoltage threshold and drop the gate into high impedance. The recovery needs a low to high edge on that phase input, which a controller holding the input high never produces.
Deadtime is not adjustable in this body, and 200 ns is a compromise. With a slow MOSFET and a large gate charge the real switching edge can be longer than that, and body diode conduction during the dead window costs efficiency, while with a fast FET the 200 ns is more than needed. Teams that need the window moved should take the QFN body, where a resistor from DT to ground sets anything from 200 ns to 2000 ns, or leave DT floating for the same 200 ns default.
The D and N letters change the polarity of the low side input, and the MODE pin on the QFN body changes it again at run time. A controller that drives INLx as an active high low side command needs the N letter, and mixing a D part into an existing board inverts every low side gate signal. On the QFN body the same choice is made by tying MODE to GVDD or leaving it open, so a board that leaves MODE floating gets the non inverted behaviour.
The two undervoltage protections do not behave the same way. A GVDD undervoltage disables all six outputs and clears automatically when the rail comes back, while a bootstrap undervoltage disables only that phase high side and waits for a new rising edge on its input. A drive that recovers from a supply dip therefore needs its controller to re issue the PWM edges, not just wait for the fault to clear.
Where three half bridges of this size are used
A 15S battery pack runs to 63 V at full charge, and a phase node on that bus sees the pack voltage plus the overshoot of the motor leads and the regen pulse when the bridge is turned off into a spinning load. The 100 V phase rating and the minus 22 V negative transient rating are what make this part fit an e bike, a power tool or a drone electronic speed controller without an extra clamp on every phase.
The gate supply is normally a 12 V rail taken from the pack through a small buck, and the 4.8 V floor matters on a 5 V rail: a 5 V rail that sags to 4.7 V during start up drops below the operating floor before the 4.6 V rising threshold is even reached, so the driver stays off. A 10 V or 12 V gate rail also keeps the MOSFET fully enhanced, which the 750 mA source current can charge quickly enough for a 20 kHz to 40 kHz PWM carrier on a 3 nF to 5 nF gate.
What the part leaves to the board
There is no current sense amplifier, no shunt, no charge pump and no serial interface on this device. Phase current has to be measured with an external shunt and amplifier, or with a Hall sensor, and the fault logic has to be built by the controller from those measurements, because the chip reports nothing beyond pulling the gate into high impedance on its own undervoltage.
The other external parts are the three bootstrap capacitors, the GVDD decoupling and a resistor divider on each phase if the controller needs phase voltage feedback. Because the bootstrap diode is inside on this letter, the diode drop of about 0.85 V appears in the droop budget and cannot be swapped for a Schottky, which is the one place where the N variant with an external diode is still the better choice on a very low gate rail.
Where this order code fits
The part fits a three phase inverter where the controller is a 3.3 V or 5 V MCU, the bus is under 100 V, and the gate drive has to be small enough to sit beside six power FETs on a compact board. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can the QFN version drop into the TSSOP footprint? No. The two bodies have different pin counts and different pin functions, because the QFN adds DT and MODE. The electrical behaviour is the same family, but the board has to change, and the deadtime setting moves from a fixed 200 ns to a resistor value.
Why does the high side gate drop out at steady state? The bootstrap capacitor is refreshed only when the phase node is pulled low. A long static high side command drains it until the bootstrap undervoltage trips, and the recovery needs a new rising edge on that input. A PWM carrier, or a deliberate refresh pulse, keeps the capacitor charged.
What happens if GVDD sags during a start up? Below the 4.35 V falling threshold all six outputs go to high impedance and the part waits. It comes back on its own once GVDD passes 4.6 V, but the controller has to re issue the gate commands, because the outputs do not resume the previous state.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.