DRV8256ERGER
Product Specifications
DRV8256ERGER
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8256ERGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8256ERGER: a 48 V brushed driver with PH/EN control and smart tune
The DRV8256ERGER is a single H bridge for brushed DC motors that runs from 4.5 V to 48 V, with 165 mOhm of combined on resistance at 24 V and 25 C and a peak output of 6.4 A. The E in the string is the PH/EN interface, one pin for direction and one for the magnitude, which is the simplest control a motor driver can offer and the one that most motion controllers already produce.
Current is measured by an internal mirror and regulated against a reference voltage that the board sets, so the inrush of a motor at start-up is held to a known value without a shunt. The regulation uses a chopping scheme the vendor calls smart tune, with selectable off times of 7, 16, 24 or 32 microseconds and fast, mixed or slow decay, which is how the same part drives a small fan and a large pump without a component change.
Spread spectrum clocking moves the switching energy across a band rather than concentrating it at one frequency, which is the difference between passing a conducted emissions limit and needing a filter. Sleep current is 2 microamps, and the protection set covers supply undervoltage, charge pump undervoltage, overcurrent and overtemperature, all reported on nFAULT.
Key data for the DRV8256ERGER
| Supply | 4.5 V to 48 V operating on VM |
| On resistance | 165 mOhm high side plus low side at 24 V and 25 C |
| Current | 6.4 A peak output, internal mirror sense, no shunt |
| Interface | PH/EN, one direction pin and one magnitude pin, 1.8 V to 5 V logic |
| Regulation | Smart tune with 7, 16, 24 or 32 microsecond off time, fast, mixed or slow decay |
| Emissions | Spread spectrum clocking, which spreads the switching energy across a band |
| Sleep current | 2 microamps, with the bridge and the internal regulator off |
Body, packing and marking data
| Body | 24-pin VQFN with exposed pad, the RGE body, 4.0 mm by 4.0 mm |
| Carrier | Large tape and reel, 330 mm reel, 12 mm tape; confirm the count on the reel row of the current addendum |
| Finish | Nickel palladium gold, moisture level 3, 168 hour floor life at 260 C |
| Second body | The same die in the 28-pin HTSSOP, 9.7 mm by 4.4 mm, is a different order code |
Reading the code before you buy it
DRV8256ERGER reads as DRV8256, E, RGE and R. The E is the PH/EN interface and the P is the PWM interface with two independent inputs, so a build that needs to brake or coast by driving both inputs has to take the P string. The RGE body is the 24-pin VQFN, and the same die in the 28-pin HTSSOP is the PWP body.
The packaging addendum for this family is one of the rows where the printed package column and the part number column drift apart in the text extract, so a buyer reading a text conversion can see the RGE string against an HTSSOP row. The device table at the front of the same document is unambiguous and puts the RGE string in the 24-pin VQFN, which is the row to quote on a purchase order.
Moisture level 3 applies to the PWP body rows and the VQFN rows carry their own level, so a build plan that mixes both bodies needs two floor life rules rather than one. That is worth writing into the process document before the first production run.
The difference between the PH/EN interface and the PWM interface shows up at the extremes of the duty range. With one direction pin and one magnitude pin, the bridge cannot be told to brake and coast independently, because the direction pin decides the polarity and the magnitude pin decides how much. A mechanism that needs a deliberate brake state, such as a shutter that must not coast past its stop, is easier to build with the two input PWM version.
The 48 V ceiling is the other number to treat with respect. A 48 V rail with a contactor or a long lead can ring well above its nominal value when the bridge turns off, and the absolute maximum is the number that decides whether the part survives. A board that runs at 48 V nominal should carry a clamp and enough bulk capacitance to keep the switching node inside the window, and the current regulation should be set so that a stall does not turn into a repeated hard current chop.
Where the 48 V member earns its place
Printers and scanners are the first case. A paper feed motor on a 24 V or 36 V rail runs in bursts, the PH/EN interface comes straight from the controller's timer, and the current regulation holds the torque during a jam without a shunt on the board.
Home appliances and vending machines are the second. A brew valve, a dispenser or a door lock draws a few amps for a second at a time, and the 2 microamp sleep current matters in a product that sits on standby for weeks between uses.
Industrial 48 V mechanisms are the third. A conveyor, a gate or a test fixture that runs from a 48 V supply sits at the top of the window with little margin, so the transient on the rail has to be checked against the absolute maximum rather than against the nominal. Substitution questions on this family belong on the how to verify a drop in replacement page.
Questions we get on this code
The first question is whether 6.4 A is continuous. It is peak. At 165 mOhm the bridge dissipates 1.1 W per amp squared, so 2 A continuous is 4.4 W and needs a solid thermal pad, while 6.4 A is a transient that the die can survive for the length of a stall.
The second question is what smart tune actually changes. It changes how the current ripple is allowed to behave during regulation, and the four off time options trade audible noise against ripple amplitude. A motor that whines at one setting is quiet at another, and that is a bench decision rather than a datasheet one.
The third question is about the decay mode. Fast decay gives a tighter current loop and more switching loss, slow decay is quieter and slower to respond, and mixed decay sits between them. The choice shows up as heat in the bridge and as noise from the motor.
The fourth question is about the 2 microamp sleep current. It is measured with the bridge and the internal regulator off, which is the state a parked product sits in for weeks. A product that wakes on a timer but leaves the driver biased does not see that number, so the quiescent budget should be checked in the state the product actually holds.
The fifth question is the difference between this part and the DRV8245. The 8245 is an automotive bridge with diagnostics and a wider interface choice at 32 A and 40 mOhm, while this one is a simpler industrial part at 48 V. Buyers comparing them can use the power management cross reference page.