DRV8244SQRYJRQ1
Product Specifications
DRV8244SQRYJRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8244SQRYJRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8244SQRYJRQ1: 21 A in a 16-pin VQFN-HR with the logic supply generated on the die
The DRV8244SQRYJRQ1 is the middle current member of the DRV824x-Q1 family at 21 A maximum output and 47 mOhm of combined on resistance in the VQFN-HR body. It runs from 4.5 V to 35 V with a 40 V absolute maximum, switches at up to 25 kHz with automatic dead time, and reports load current as an analogue voltage on IPROPI from a high-side mirror.
The S in the string is the SPI variant with an internally generated logic supply. That is the difference that saves board work: the part makes its own 3.3 V rail for the digital interface, so a module that only has the battery and a CAN transceiver can talk to it without adding a regulator. The cost is that the interface level is fixed by the part rather than by the controller, which is why the P variant exists for boards that already have a logic rail.
The RYJ body is 16 pins of VQFN-HR at roughly 3 mm by 4.5 mm with the thermal pad on the underside, and the 47 mOhm figure belongs to that body. The HVSSOP version of the same die is 60 mOhm, so the package choice is worth about a quarter of the conduction loss at the same current.
Key data for the DRV8244SQRYJRQ1
| Supply | 4.5 V to 35 V operating, 40 V absolute maximum on VM |
| On resistance | 47 mOhm high side plus low side in VQFN-HR, 60 mOhm in HVSSOP |
| Current | 21 A maximum output, high-side mirror sense on IPROPI |
| Interface | SPI with an internally generated logic supply, plus a fault pin |
| Switching | PWM up to 25 kHz, automatic dead time, configurable slew rate and spread spectrum |
| Diagnostics | On and off state load diagnostics, VM monitoring, overcurrent, overtemperature |
| Qualification | AEC-Q100 grade 1, minus 40 C to plus 125 C ambient, functional safety capable |
Body, packing and marking data
| Body | 16-pin VQFN-HR with thermal pad, the RYJ body |
| Carrier | 3000 pieces on a large tape and reel |
| Finish | Nickel palladium gold, moisture level 2, one year floor life at 260 C |
| Marking | 8244S plus the lot and date code on the reel label |
Reading the code before you buy it
DRV8244SQRYJRQ1 reads as DRV8244, S, RYJ and RQ1. The S marks the SPI variant with the internal logic supply, RYJ is the 16-pin VQFN-HR body, and RQ1 is the automotive qualification with a large reel. The same part in HVSSOP is the DGQ body at 60 mOhm, which is a different order code and a different thermal calculation.
Because the S variant generates its own logic rail, it is the one to choose when the module has no spare 3.3 V. But it also means the SPI lines are referenced to a rail that the part controls, so the controller has to tolerate the level that comes back rather than the level it sends. A board with a controller that is strict about input thresholds should take the P variant instead.
The current scaling is the next thing to fix in the drawing. The IPROPI output is a current that a resistor turns into a voltage, so the same silicon can report 21 A as 3 V or as 1 V depending on one resistor. A supplier quoting the part against a competitor has to be asked for that resistor value, otherwise the two current readings are not comparable.
The thermal path is the part of this device that a specification sheet cannot carry. A 16-pin VQFN-HR at 47 mOhm dissipates 8.3 W at 21 A, and that heat leaves through a pad that is smaller than the pad of a 28-pin HTSSOP. The copper under it, the number of vias into the ground plane and the airflow across the board decide whether the part holds 21 A for a second or a minute. A module reusing an older board with a thinner copper layer will see a higher die temperature at the same load.
The diagnostics are the second half of the value. In the off state the part can push a small current into the load and measure the voltage that comes back, which separates an open circuit from a short to ground and from a short to battery. In the on state it compares the current it measures against the expected value for the commanded duty. Together those two checks cover the four failure classes a body module has to report.
Where the 21 A member earns its place
Steering and braking actuators are the first case. An electric power steering motor in a small vehicle draws tens of amps in a stall, and the 21 A continuous figure with 47 mOhm keeps the conduction loss near 20 W at the peak, which the VQFN-HR pad can move into the bracket. The 25 kHz PWM ceiling is above the audible band and inside the switching loss budget of the FET.
Thermal management flaps and grille shutters are the second case. These run a few times per drive cycle, need diagnostics to prove they moved, and sit in a location where the ambient can reach 105 C. Grade 1 qualification covers that, and the off-state diagnostics prove the motor is still connected when the flap is commanded.
Body hydraulics and pump modules are the third. Buyers sourcing this class of part against a delivery date can compare the three current members on the power management cross reference page, which lists the on resistance and the body for each one.
Questions we get on this code
The first question is whether the internal logic supply can feed anything else. It cannot be treated as a general rail. It exists to run the digital core and the SPI interface, and its current budget is set by that job rather than by an external load.
The second question is how the part behaves when the battery drops during a cold crank. The 4.5 V floor is below the 6 V that a cranking battery can fall to, so the bridge keeps driving through a crank, and the undervoltage threshold sits at the bottom of the window rather than in the middle.
The third question is about paralleling two half bridges for a higher current. The family allows independent half-bridge mode, and two devices can be paralleled, but the current sense then reports the sum through one mirror and the loop gain changes. That is a job for a validation plan, not for a quick substitution.
The fourth question is about the reel. The 3000 piece large reel on the RYJ body is a standard feeder size, but a prototype line that only needs a hundred pieces will be cutting a reel, and a cut reel without the original label is a date code risk. A module built in low volume should ask for the tape and reel to stay sealed until the first article is signed off.
The fifth question is the difference between functional safety capable and compliant. The DRV824x-Q1 documentation supports a claim; the claim itself belongs to the module. A supplier asked for ISO 26262 evidence should be asked for the safety manual and the FMEDA, and the supplier quality audit page lists what a paperwork review normally covers.