DRV8243PQDGQRQ1
Product Specifications
DRV8243PQDGQRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8243PQDGQRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8243PQDGQRQ1: a 12 A automotive H bridge with an SPI port and a 28-pin body
The DRV8243PQDGQRQ1 is the smallest current member of the DRV824x-Q1 family, a fully integrated H bridge for automotive body and powertrain loads that runs from 4.5 V to 35 V with a 40 V absolute maximum. The combined on resistance of the high-side and low-side FETs is 98 mOhm in the HVSSOP body and 84 mOhm in the VQFN-HR body, and the maximum output current is 12 A.
The P in the string is the SPI variant with an externally supplied logic rail. That matters on a board that already has a 3.3 V or a 5 V rail for the controller, because the interface then follows the controller and not the other way round. The S variant generates its own logic supply and the H variant has no serial port at all, which is the three way split that decides most of the part selection work on this family.
Current is measured on the high side by a mirror and reported as an analogue voltage on the IPROPI pin, so the board does not carry a shunt in the motor path. Load diagnostics run in both the on state and the off state, which is what lets a body controller tell a burnt bulb from a missing one, and the nFAULT pin reports undervoltage, overcurrent and overtemperature with a configurable reaction, latched or retry.
Key data for the DRV8243PQDGQRQ1
| Supply | 4.5 V to 35 V operating, 40 V absolute maximum on VM |
| On resistance | 98 mOhm high side plus low side in HVSSOP, 84 mOhm in VQFN-HR |
| Current | 12 A maximum output, high-side mirror sense on IPROPI |
| Interface | SPI with an externally supplied logic rail, plus a hardware fault pin |
| Switching | PWM up to 25 kHz with automatic dead time, configurable slew rate and spread spectrum |
| Diagnostics | Load diagnostics in on and off state, VM monitoring, overcurrent, overtemperature |
| Qualification | AEC-Q100 grade 1, minus 40 C to plus 125 C ambient, functional safety capable |
Body, packing and marking data
| Body | 28-pin HVSSOP with thermal pad, the DGQ body |
| Carrier | 2500 pieces on a large tape and reel |
| Finish | Nickel palladium gold, moisture level 3, 168 hour floor life at 260 C |
| Marking | 8243P plus the lot and date code, printed on the reel label |
Reading the code before you buy it
DRV8243PQDGQRQ1 reads as DRV8243, P, DGQ and RQ1. The 8243 is the 12 A member, the 8244 is 21 A at 47 mOhm and the 8245 is 32 A at 32 mOhm, all three with the same pin function so a board can scale its current without changing its control interface. The Q1 is the automotive qualification, and there is no industrial version of this exact string.
The P and S split is the part that trips up purchase orders. P expects the logic rail to come from outside, S generates it internally, and a board wired for one will not run with the other even though the body and the footprint are identical. The H variant removes the SPI port entirely, which is cheaper and less flexible, and it is the one to choose when the controller has no spare serial port and the load does not need diagnostics.
The two bodies are the second trap. The same die is offered in HVSSOP at 98 mOhm and in VQFN-HR at 84 mOhm, and the difference in on resistance is a package difference rather than a die difference. A thermal calculation done with the VQFN figure and then built in HVSSOP will run hotter than expected by about 15 per cent of the conduction loss.
One number that comes up in every review is the 25 kHz switching ceiling. It exists because a bridge this size at 35 V would lose more in switching than it gains in ripple, and because the audible band has to be cleared. A load that needs a faster loop, such as a fuel pump on a small inductance, is better served by a current regulated stage than by pushing the frequency. The part also inserts the dead time itself, so a controller that cannot guarantee a gap between the two inputs is still safe.
Where a 12 A automotive bridge earns its place
Body control modules are the first case. A seat motor, a mirror fold motor or a window lift draws a stall current in the range this part covers, the load diagnostics catch an open winding or a short to ground before the module is fitted to the vehicle, and the SPI port lets the module report which output failed without extra wiring.
Pumps and valves are the second case. A 12 V or 24 V automotive pump runs intermittently, and the current regulation holds the inrush inside the connector rating. The 25 kHz PWM ceiling keeps the switching above the audible band, which is a comfort requirement rather than an electrical one, and it is the reason the family stops where it does.
The qualification is the third case. AEC-Q100 grade 1 covers minus 40 C to plus 125 C ambient, which is the temperature a module behind a dashboard actually sees, and the functional safety documentation lets a supplier claim a diagnostic coverage figure rather than assert one. Buyers who need that paper trail in a purchase order can use the OEM procurement page to see what evidence the line normally carries.
Questions we get on this code
The first question is about moisture level 3. A 168 hour floor life means the reel has to be baked after a week out of the dry pack, and a production line that ignores it gets popcorn voids under the thermal pad. On a 28-pin body with a large pad that failure is invisible until the thermal test.
The second question is how accurate the current sense is. The mirror is trimmed and the IPROPI output is a scaled copy of the high-side current, so accuracy is good in the middle of the range and degrades near zero, which is why an open load diagnostic uses the off-state check rather than a current threshold. The inspection route for incoming reels is on the incoming inspection plan page.
The third question is whether the part can drive two independent loads. It can, in the independent half-bridge mode, with the two half bridges no longer interlocked. In that mode the automatic dead time still applies inside each half bridge and the current sense reports the current of whichever half bridge is conducting.
The fourth question is whether the part can replace a relay and a fuse in an existing housing. It can, with the caveat that the off-state diagnostics need a path to the load that a relay contact did not, and the module has to be able to read the fault pin. A supplier that swaps the relay without changing the harness loses the very diagnostics that justified the change.
The fifth question is about the SPI device identifier. Each member of the family answers with its own identifier, so the controller can tell a 8243 from a 8245 on the same bus, which is useful when one module board carries two power levels and the bill of materials changes by vehicle variant.