Contact Us

DRV8231ADSGR

Brand: Texas Instruments
Texas Instruments DRV8231ADSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8231ADSGR — Power Management & Signal Chain | Superb Automation

DRV8231ADSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8231ADSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8231ADSGR: the 33 V member of the 8-pin brushed driver family

The DRV8231ADSGR is a brushed DC motor driver that runs from 4.5 V to 33 V and delivers 3.7 A peak through an H bridge with 600 mOhm of combined on resistance. It is the higher voltage member of the same 8-pin family as the DRV8213, and it is pin to pin with the DRV8870 at 6.5 V to 45 V with 565 mOhm, and with the DRV8231 which uses the same 600 mOhm bridge.

Current is measured by an internal mirror and reported as an analogue voltage on IPROPI, so the board does not need a shunt. The same signal is used inside the part for current regulation, which means a stall or an inrush can be held to a limit set by a resistor and a reference rather than by controller timing. The inputs take 1.8 V, 3.3 V and 5 V logic, and the 8-pin WSON body is 2.00 mm by 2.00 mm with a thermal pad.

The sense mirror is what makes the part usable without a shunt. A shunt in the low-side path costs board space, adds a kelvin connection and dissipates power at full current, while a mirror inside the bridge reports the same current as a scaled copy. The trade is accuracy at very low currents, where the offset of the mirror dominates, and that is why the current regulation threshold on this family is normally set well above the idle current of the mechanism.

The other consequence of the mirror is that the reported current tracks the bridge rather than the load. During a free-wheel interval the current path changes, and the reported value follows the conducting pair rather than the motor current alone. A controller that integrates the sense signal to estimate position has to account for that, which is the kind of detail that shows up in a validation report and not on the front page of the document.

The point of this part is the 24 V rail. A valve, a damper actuator or a printer mechanism that runs from 24 V sits with margin inside the 33 V window and well clear of the 40 V transient that a 24 V supply can produce on a long lead. The 4.5 V floor is what keeps the same board usable on a 5 V rail during a brown-out test.

Key data for the DRV8231ADSGR

Supply4.5 V to 33 V on VM, logic from 1.8 V, 3.3 V or 5 V
On resistance600 mOhm high side plus low side
Current3.7 A peak output, internal mirror sense on IPROPI
RegulationCurrent limit set by the IPROPI resistor and the reference pin
QuiescentSleep mode disables the bridge and drops the quiescent current, quoted by the vendor at 24 V and 25 C junction
ProtectionUndervoltage lockout, auto-retry overcurrent, thermal shutdown
FamilyPin to pin with DRV8870 at 6.5 V to 45 V and 565 mOhm, and with DRV8231

Body, packing and marking data

Body8-pin WSON, the DSG body, 2.00 mm by 2.00 mm with thermal pad
Carrier3000 pieces on a large tape and reel
FinishNickel palladium gold, moisture level 1, 260 C unlimited floor life
Note on bodiesThe addendum also prints a DDA row for the SO PowerPAD body, so the body has to be named on the order

Reading the code before you buy it

DRV8231ADSGR is DRV8231A, DSG and R. The A suffix marks the revision of the die that carries the IPROPI mirror and the current regulation, and the plain DRV8231 is the earlier string with the same bridge and a different sense arrangement. The DSG body is the WSON; the DDA body in the same addendum is the SO PowerPAD, and it is a different footprint and a different thermal path.

Two strings in the same document, DRV8231ADSGR and DRV8231ADSGR.A, are printed with different moisture levels, level 2 with a one year floor life against level 1 unlimited. That is a real difference on a production line that does not bake parts before reflow, and the two rows are separate orderable numbers rather than the same part under two names.

The third item is the family pinout. Because DRV8870, DRV8231 and DRV8231A share a footprint, a board can be built with any of them and the difference shows up in the current sense path, in the voltage window and in the on resistance. A substitution across those three changes the sense gain and the thermal margin at the same time.

Where the 33 V member earns its place

Industrial valves and dampers are the first case. A 24 V actuator that holds position against a spring draws a continuous current well under 1 A and a stall current near 3 A, and the IPROPI output lets the controller detect the stop without a limit switch. The 33 V rating leaves room for the inductive kick that a 24 V rail produces when the bridge turns off.

Printers, scanners and ATMs are the second case. A paper feed or a shutter motor runs in bursts, the current regulation holds the torque during the burst, and the 2 mm body fits beside the mechanism. Coffee machines and vending equipment use the same part for the brew valve and the dispenser.

Packaging is the last practical detail. The DSG body ships 3000 pieces on a large tape and reel with a 330 mm reel and a 12 mm tape width, which is a standard feeder on most surface mount lines. A prototype build that only needs fifty pieces has to come from a broken reel or from a distributor cut, and that is the point where a date code check matters more than the price, because a reel that has been open for a year behaves differently in reflow than one from the current lot.

Buyers replacing a DRV8870 on an existing board are the third case. The footprint is the same, the voltage window is narrower and the sense path changes from an external shunt to an internal mirror, so the change is a software and a resistor change rather than a board change. The check route is on the how to verify a drop in replacement page.

Questions we get on this code

The first question is whether 3.7 A is a continuous rating. It is a peak. At 600 mOhm the bridge dissipates 0.6 W per amp squared, so a 1 A continuous load is 0.6 W and a 2 A continuous load is 2.4 W, and the 2 mm body only carries the second figure with a good thermal pad and airflow.

The second question is whether it can replace a DRV8870 directly. Same pins, different voltage window and different sense method, so a 36 V rail that worked with the 8870 is outside the 33 V window of this part. The substitution is valid on a 24 V rail and not on a 36 V one.

The third question is about the current limit accuracy. The mirror is trimmed but the limit is set by an external resistor, so the tolerance of that resistor and the offset of the reference both land in the limit. A 20 per cent window is realistic and a 5 per cent window needs a trim in production.

The fourth question is about second sourcing the 8-pin family. Several parts share the footprint and each one has a different combination of voltage and sense, which is exactly what the pin to pin cross reference page is for.

The fifth question is about the 33 V ceiling on a 24 V rail. A 24 V supply with a long lead can produce a transient above 33 V when the bridge turns off, so the rail needs a clamp or a bulk capacitor close to the bridge. The absolute maximum is not the operating limit, and a part that runs at 24 V nominal should be checked against the transient, not against the nominal.