DRV8231ADDAR
Product Specifications
DRV8231ADDAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8231ADDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8231ADDAR: A 33 V Brushed Driver That Mirrors Its Current Instead of Shunting It
DRV8231ADDAR is a brushed DC motor driver with an integrated current mirror in a SO PowerPAD (DDA) body of 8 pins. It works from 4.5 V to 33 V, delivers 3.7 A peak, and replaces the usual sense resistor with a current mirror brought out on the IPROPI pin, so the controller sees a scaled copy of the load current and still sets the regulation point with a reference voltage. Bridge resistance is 600 mΩ, sleep current is under a microamp, and the eight pin body is the same footprint as the shunted members of the family.
Order code and package
| Ordering string | DRV8231ADDAR |
| Family document | DRV8231 and DRV8231A, SLVSFZ7, November 2021 |
| Package | SO PowerPAD (DDA), 8 pins, 4.9 mm by 6.0 mm with an exposed pad |
| Reel and packing | 3000 pieces on a large reel, NiPdAu lead finish |
| Moisture level | Level 2, 260 C peak, one year floor life |
| Body marking | DRV8231 |
| Temperature range | minus 40 to plus 150 degrees |
| Small body sibling | DRV8231ADSGR in WSON 2 by 2 mm, Level 1, marking 31 |
| Current sense | Internal mirror on IPROPI, no external shunt |
| Interface | PWM with IN1 and IN2 |
| Charge pump | Internal, so the high side FETs reach 100 per cent duty |
| Ordering caveat | The published addendum prints the DRV8231DDAR and DRV8231DSGR rows, not the A suffix rows |
Electrical parameters that decide the application
| Supply range | 4.5 to 33 V |
| Peak output current | 3.7 A |
| Bridge resistance | 300 mΩ source and 300 mΩ sink at 24 V and 1 A, 600 mΩ for the pair |
| Current output | IPROPI, a mirror of the high side current into an external resistor |
| Regulation reference | VREF compared against the mirrored voltage on IPROPI |
| Off time | 25 us fixed |
| Blanking time | 2 us |
| Supply current | 3 to 4 mA in active mode |
| Sleep current | Under 1 uA at 24 V and 25 C |
| Undervoltage | Rising 4.15 to 4.45 V, falling 4.05 to 4.35 V |
| Wake up time | 250 us from sleep to output |
| Output delay | 0.7 to 1.0 us from input to output |
| Dead time | 200 ns |
| Thermal shutdown | 175 C typical with 40 C of hysteresis |
Family variants and how they differ
| DRV8231 | The shunted version, ISEN pin and 600 mΩ, same footprint |
| DRV8251 | 4.5 to 48 V and 450 mΩ with a shunt, for a higher rail |
| DRV8251A | 4.5 to 48 V and 450 mΩ with the mirror |
| DRV8870 | 6.5 to 45 V and 565 mΩ with a shunt, the part this family was derived from |
| DRV8231ADSGR | The same die in the 2 by 2 mm WSON body |
| Mirror against shunt | The mirror removes the shunt and its heat, the shunt leaves the sense signal on a pin |
| Board reuse | Both sense methods share the pinout, so one board can carry either with a component not fitted |
Points to check before this part goes on a BOM
The A letter changes the sense method, not the bridge. The DRV8231 puts a resistor in the low side path and brings the voltage out on ISEN, while the DRV8231A mirrors the high side current and brings a current out on IPROPI. The regulation loop is the same idea in both cases, a reference voltage compared against the sensed quantity, and the board footprint is deliberately the same so a programme can change its mind.
The mirror has no published gain in this revision of the document, and that is a real procurement point. The electrical table is written around the ISEN variant, with the sense amplifier gain stated as 10 V per volt and the trip equation given in terms of an external resistor, while the A variant is documented in the application section as a way to remove that resistor. A trip point for the A part therefore has to be derived from the vendor's IPROPI resistor example or measured on the bench, not copied from the ISEN equation.
The ordering string is not printed in the addendum as written. The published rows list DRV8231DDAR and DRV8231DSGR, both active, and there is no row carrying the A suffix, even though the document title covers both variants. That does not mean the part does not exist, and it does mean a purchase order for this exact string should be confirmed against the vendor or against a distributor record before a schedule is set.
The 33 V ceiling is what separates this part from the 48 V members of the same family, and it is a rail decision rather than a load decision. A 24 V system with a regen spike can exceed 33 V briefly, so the supply has to be clamped or the higher voltage member has to be used. The 4.5 V floor, on the other hand, is low enough for a 5 V rail, which the older parts in the catalogue cannot do.
Sleep current under a microamp is what lets the rail stay connected in a battery product, and the 250 us wake up time is what the firmware has to allow for. A controller that pulls the inputs out of sleep and expects the motor to move within a few microseconds will see nothing for a quarter of a millisecond, which at the start of a positioning move is usually harmless and in a chopping loop is not.
Removing the shunt from a 3 A mechanism
A shunt in a 3 A path is a resistor that has to carry the current, dissipate the heat and be measured with a kelvin connection, and it is one of the more expensive square millimetres on a small board. The mirror replaces it with a transistor inside the bridge that is a known fraction of the power FET, and the only external component left is the resistor that turns the mirrored current into a voltage.
The cost is accuracy. A mirror is only as good as the matching between the sense transistor and the power FET across temperature, and the vendor does not publish a gain figure for this variant in the current revision, so a board that needs a precise current reading should either measure it or use the shunted version. A board that needs a rough stall threshold is well served by the mirror.
The pin compatible family
Four parts share the eight pin footprint and differ in supply range, resistance and sense method, which is unusual and useful. A board laid out for the DRV8231 can take the DRV8251 for a 48 V rail, or the A version of either, and the only change is the component that sets the trip point and whether the shunt position is populated.
That kind of pin compatibility matters when a programme runs for years and the supply chain moves. A second source or a replacement can be qualified on the same board, and the current sense method can be changed without a board revision, which is the sort of flexibility that a purchasing team values as much as an engineering team does.
Where this order code fits
The part fits a 12 V or 24 V brushed mechanism on a board where the shunt and its heat are unwelcome and a rough current reading is enough to detect a stall. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is this the same as the DRV8231 with a different pin? The bridge is the same and the sense method is different. The DRV8231 uses an external shunt on ISEN, the A version mirrors the high side current onto IPROPI. The footprint is shared, so the change is a component and a resistor value rather than a board.
Why is the A suffix missing from the addendum? The document's packaging section lists the plain part numbers only. That is a documentation gap rather than a status change, and it means the exact string should be confirmed with the vendor or a distributor before an order is placed.
How is the current limit set on this variant? By the voltage on IPROPI against VREF, with an external resistor turning the mirrored current into a voltage. The vendor application section gives a resistor example, and the exact gain should be confirmed on the bench because this revision prints the gain for the shunted variant.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.