Contact Us

DRV8162DGSR

Brand: Texas Instruments
Texas Instruments DRV8162DGSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8162DGSR — Power Management & Signal Chain | Superb Automation

DRV8162DGSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8162DGSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8162DGSR: a 100 V half-bridge gate driver with split supplies for safe torque off

The DRV8162DGSR drives one high-side and one low-side N-channel FET in a half bridge, with the high-side source rated to 102 V absolute maximum and the gate drive taken from an 8 V to 20 V GVDD rail. The bootstrap diode is inside the part, so the high-side supply needs one capacitor and no external diode. Sixteen peak current settings between 16 mA and 1000 mA source, and 32 mA to 2000 mA sink, are selected with a resistor, and the source to sink ratio can be set to 1:1, 1:2 or 1:3.

This is the member of the DRV816x family with a split gate drive supply. GVDD and GVDD_LS are separate pins, which lets a controller drop the low-side drive independently of the high-side drive and reach a safe torque off state without cutting the whole rail. The DRV8162L is the same part with a 5 V gate drive supply for logic level FETs, and the DRV8161 is the member that adds a low-offset current sense amplifier instead of the split supply.

The peak current setting is a resistor to ground, not a register, so the gate drive strength is fixed by the board and cannot be changed by a bus glitch. That is deliberate on a 100 V stage: the slew rate that keeps a phase node inside its transient window is a hardware decision that should survive a controller reset. The same resistor network sets the source to sink ratio, which is how a board trades turn-on speed against ringing without changing the FET.

The protection set is aimed at a motor phase rather than a static load, which is the difference between a driver that reports a fault and a driver that survives one. Thirteen levels of VDS overcurrent detection, gate to source handshake on every switching event, undervoltage on the gate drive and on the bootstrap capacitor, thermal shutdown, and an nFAULT output that reports which of them tripped. The nDRVOFF pin shuts the power stage down independently of the PWM input, which is the pin a safety relay or a supervisor drives.

Key data for the DRV8162DGSR

TopologyHalf bridge, one high-side and one low-side N-channel FET, external
Voltage5 V to 90 V operating on the FET drain, 102 V absolute maximum on the high-side source
Gate drive8 V to 20 V GVDD, integrated bootstrap diode, trickle charge pump for 100 per cent duty
Peak current16 mA to 1000 mA source, 32 mA to 2000 mA sink, 16 levels with three ratio options
TimingDead time adjustable from 20 ns to 900 ns, slew rate up to 50 V per ns
Protection13 level VDS overcurrent, gate drive undervoltage, bootstrap undervoltage, thermal shutdown
Logic3.3 V and 5 V inputs, 2-pin or 1-pin PWM, independent PWM mode

Body, packing and marking data

Body20-pin VSSOP, the DGS body, 5.1 mm by 4.9 mm
Carrier5000 pieces on a large tape and reel
FinishNickel palladium gold, moisture level 1, 260 C unlimited floor life
TemperatureMinus 40 C to plus 125 C, industrial grade, no AEC-Q100 suffix on this string

Reading the code before you buy it

DRV8162DGSR reads as DRV8162, DGS and R. The family has three members and the differences matter more than the suffix. The DRV8161 carries a current sense amplifier with four gain settings, 5, 10, 20 and 40 V per V, and a single gate drive supply. The DRV8162 adds the split supply and drops the amplifier. The DRV8162L keeps the split supply and drops the gate drive rail to 5 V.

So a board that needs phase current information has to choose between an external shunt amplifier and the DRV8161, and a board that needs a redundant shutdown path has to take the DRV8162 or the L version. Ordering the wrong letter gives a part that fits the same footprint and behaves differently, which is the kind of mismatch that only shows up at the safety test.

The negative transient rating on the switch node is minus 20 V, which is a real number for a phase node with cable inductance and not a marketing figure. It is the reason a long motor cable does not need an external clamp on every board, although a phase node driven hard into a short still deserves a look at the scope during validation.

Where the half bridge earns its place

Battery powered transport is the first case. An AGV or an autonomous mobile robot runs a 48 V bus, switches at 20 kHz to 40 kHz, and needs a gate drive that will not destroy the FET when a wheel hits a kerb. The 13 level VDS detection catches the desaturation before the die cooks, and the soft shutdown sequence ramps the gate down instead of chopping the current.

Drone and UAV propulsion is the second. A 6S to 12S pack sits inside the 100 V window with margin, the 16 peak current settings let the same board carry a small or a large FET without a resistor change, and the dead time insertion removes the shoot-through risk that a fast microcontroller can create. More on that class of build is on the drone and UAV component page.

The gate drive supply itself is worth a note. GVDD sets the gate voltage, and the recommended window runs from 8 V to 20 V, so a 12 V rail can feed it directly while a 5 V rail cannot unless the L version is ordered. A board that powers GVDD from the same 5 V that feeds the controller will sit below the undervoltage threshold and report a fault that looks like a dead FET.

Linear transport, stepper drives and solenoid banks are the third case, where the half bridge is used as a building block rather than as a complete inverter. Two of these parts plus a controller make a full H bridge, and three make a three-phase stage, which is why the family is quoted per half bridge rather than per motor.

Questions we get on this code

The first question is whether a current sense amplifier is included. It is not on this string. The DRV8161 has it, the DRV8162 and the L version do not, and a board that needs cycle by cycle current limiting has to add a shunt and an amplifier or move to the 8161.

The second question is what safe torque off actually requires. The split supply lets the low-side drive be removed while the high-side stays alive, which is one of the two channels a safety relay needs to prove. It is a component level building block, not a certified subsystem, so the diagnostic coverage claim belongs to the machine builder and not to the driver.

The third question is about the external FET choice. The 1 A source and 2 A sink ceiling suits a FET with 20 nC to 100 nC of total gate charge at 20 kHz, and beyond that the switching loss in the driver starts to matter. Gate charge, not current rating, is the number to match. Sourcing this class of driver against a long lead time is what the component lead time page covers.

The fourth question is about 100 per cent duty. The trickle charge pump keeps the bootstrap capacitor topped up when the high side stays on, so a stalled motor holding full torque does not lose its gate drive after a few milliseconds.

The fifth question is whether the same board can run at 48 V and at 96 V. The FET, not the driver, sets the voltage ceiling once the drain stays under the 102 V absolute maximum, but the gate drive current and the dead time have to be re-chosen for the higher bus, because the same resistor value gives a different switching loss at twice the voltage.