Contact Us

DRV5055A1QDBZR

Brand: Texas Instruments
Texas Instruments DRV5055A1QDBZR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV5055A1QDBZR — Power Management & Signal Chain | Superb Automation

DRV5055A1QDBZR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV5055A1QDBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV5055A1QDBZR: A Ratiometric Hall Sensor That Reads Half the Rail at Zero Field

DRV5055A1QDBZR is a ratiometric linear Hall effect sensor in a SOT-23 (DBZ) body of 3 pins. It runs from a 3.3 V or 5 V rail, sits at half the rail with no field present, and swings 100 mV per millitesla, so a plus or minus 21 mT field covers most of the output range. The A letter adds compensation for the way a magnet loses strength as it warms, the sensing bandwidth is 20 kHz, and the three pin SOT-23 needs nothing but a supply and a decoupling capacitor.

Order code and package

Ordering stringDRV5055A1QDBZR
Family documentDRV5055, SBAS640C, revised June 2026
PackageSOT-23 (DBZ), 3 pins
Reel and packing3000 pieces on a large reel, tin lead finish
Moisture levelLevel 2, 260 C peak, one year floor life
Body marking55A1
Temperature rangeminus 40 to plus 125 degrees
Through hole siblingDRV5055A1QLPG in TO-92, 1000 pieces in bulk
Sensitivity optionA1, 100 mV per mT at 5 V, plus or minus 21 mT of range
Temperature compensationIncluded on the A options, absent on the Z options
Offset at zero fieldHalf of VCC by architecture, 2.5 V on a 5 V rail

Electrical parameters that decide the application

Supply range3.0 to 3.63 V and 4.5 to 5.5 V, two specified windows
Supply current3 mA typical and 4 mA maximum at 5 V, lower at 3.3 V
Sensitivity at 5 V100 mV per mT typical, 95 to 105 over temperature
Sensitivity at 3.3 V60 mV per mT typical, 57 to 63
Quiescent output2.50 V typical at 5 V, 2.43 to 2.57 over temperature
Field rangePlus or minus 21 mT for the A1 option at 5 V
Sensing bandwidth20 kHz
Propagation delay10 us from a change in field to a change in output
Output drivePlus or minus 1 mA
Noise6 mV peak to peak at the output for the A1 option with a 5 V rail
Lifetime driftUnder 0.5 per cent of the quiescent voltage over 1000 hours at high temperature
Ratiometry errorAbout 0.2 per cent per degree on the quiescent point

Family variants and how they differ

DRV5055A1100 mV per mT and plus or minus 21 mT, the highest sensitivity with compensation
DRV5055A250 mV per mT and plus or minus 42 mT
DRV5055A325 mV per mT and plus or minus 85 mT
DRV5055A412.5 mV per mT and plus or minus 169 mT
DRV5055A866 mV per mT and plus or minus 32.5 mT, the option for a mid range field
DRV5055Z1 to Z4The same sensitivities without magnet temperature compensation
A against ZThe A options flatten the drift of a neodymium magnet, the Z options leave the output uncompensated
Package choiceSOT-23 for surface mount, TO-92 for a leaded assembly

Points to check before this part goes on a BOM

Ratiometric means the output is a fraction of the supply, not a fixed voltage. With 5 V on the rail the zero field point sits at 2.5 V and the sensitivity is 100 mV per mT, and with 3.3 V the same field gives 60 mV per mT around 1.65 V. An ADC that uses the same rail as its reference therefore cancels the supply tolerance completely, which is the reason this architecture is chosen over the fixed output sensors in the same catalogue.

The A letter is a magnet compensation, not a sensor calibration. Neodymium magnets lose roughly a tenth of their strength between room temperature and 125 degrees, and the A options bend the sensitivity curve to follow that loss so that a position reading stays put as the mechanism warms. The Z options leave the output uncompensated, which is correct when the field comes from a coil or from a magnet that is held at a stable temperature.

The field range and the sensitivity are the same choice seen twice. The A1 option reads plus or minus 21 mT at 100 mV per mT and the A4 option reads plus or minus 169 mT at 12.5 mV per mT, so a mechanism with a large magnet travel and a coarse requirement takes the low sensitivity option and a mechanism with a small travel and a fine requirement takes the high one. Choosing the most sensitive option for a large field simply clips.

The 20 kHz bandwidth is far above what a mechanical position needs, which is what allows the part to be used for a current sensor built around a coil or for a rotation counter. The 10 us of propagation delay then becomes the limit on how fast a control loop can close, and a motor commutation scheme that needs the field reading within a few microseconds has to account for it.

The output drives plus or minus 1 mA, which is enough for a short trace into an ADC and not enough for a long cable. A sensor mounted on a separate board through a harness needs a buffer or a lower impedance path, and the RC filter that removes the 6 mV of noise has to be sized against the 1 mA drive rather than against a low impedance source.

Position sensing with a compensated sensor

A throttle pedal, a valve stem or a joystick measures a magnet moving over a few millimetres, and the field at the sensor is a few milliteslas at most. The A1 option covers that with 100 mV per mT, so a 5 mm travel that changes the field by 4 mT produces 400 mV of swing, which is a comfortable signal for a 12 bit converter working from the same 5 V rail.

Because the output is ratiometric, the converter can take its reference from the sensor rail and the reading becomes independent of whether that rail is 4.9 V or 5.1 V. The remaining error is the offset window and the sensitivity window, both of which are specified over the full temperature range, so a production line can either calibrate each unit or accept the spread.

Where the uncompensated option is the right one

A current sensor that measures the field of a coil, or a rotation counter that reads a steel gear, does not see a magnet that drifts with temperature. In those cases the compensation of the A options actually introduces an error, because the field being measured does not fall with temperature while the sensor assumes it does. The Z options exist for exactly that case.

The difference between the two is a few per cent of reading over the temperature range, which matters for a position measurement and does not matter for a switch. A board that only needs a threshold crossing can use either option and set the threshold in the middle of the travel.

Where this order code fits

The part fits a position measurement on a 3.3 V or 5 V rail where the converter shares the sensor supply as its reference and the magnet is a neodymium one that warms up with the mechanism. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What is the output at zero field? Half of the supply, 2.5 V on a 5 V rail and 1.65 V on a 3.3 V rail, with a window of about 70 mV around that point over temperature. The output then moves 100 mV per mT at 5 V in the direction set by the pole.

Does the sensitivity change with the supply? Yes, and that is the point of the ratiometric architecture. Sensitivity falls with the rail, 100 mV per mT at 5 V and 60 mV per mT at 3.3 V, so an ADC referenced to the same rail reads the same field regardless of the exact supply voltage.

When should the Z option be used instead of the A option? When the field does not come from a magnet that changes strength with temperature, for example a coil or a steel target. The A option assumes a neodymium magnet and would over correct in those cases.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.