Contact Us

DRV5032ZEDBZR

Brand: Texas Instruments
Texas Instruments DRV5032ZEDBZR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV5032ZEDBZR — Power Management & Signal Chain | Superb Automation

DRV5032ZEDBZR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV5032ZEDBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV5032ZEDBZR: A 63 mT Omnipolar Hall Switch in SOT-23 That the Vendor Now Prints as Obsolete

DRV5032ZEDBZR is an ultra low power digital switch Hall effect sensor in a SOT-23 (DBZ) body of 3 pins. It samples the field 20 times a second and draws 1.3 uA from a supply anywhere between 1.65 V and 5.5 V, which is what puts it on a coin cell or a meter that has to run for a decade. The ZE letter is the 63 mT threshold, the highest in the family, and it is the version chosen where the magnet sits far away or where steel nearby has to be ignored. This particular DBZ string is printed as Obsolete Production in the vendor addendum dated 30 September 2026.

Order code and package

Ordering stringDRV5032ZEDBZR
Family documentDRV5032, SLVSDC7H, revised December 2024
PackageSOT-23 (DBZ), 3 pins, 2.92 mm by 2.37 mm
Reel and packing3000 pieces on a large reel
Lifecycle on this rowObsolete Production on the DBZ row of the addendum
Active rows for the same letterDRV5032ZEDBZR.A and DRV5032ZELPG, both in the TO-92 body
Body marking1M8W or 2ZE, depending on the lot
Lead finish on this rowSN, with the moisture level printed as not applicable for the package type
Temperature rangeminus 40 to plus 85 degrees
Package options in the device comparison tableX2SON (DMR) and TO-92 (LPG)
Output options inside the ZE letterPush pull and open drain are both published for 63 mT
Sampling rate20 Hz, so one output update every 50 to 75 ms

Electrical parameters that decide the application

Supply range1.65 to 5.5 V, no separate logic rail
Average supply current, 5 Hz letter0.54 uA
Average supply current, 20 Hz letter1.3 uA
Average supply current, 80 Hz letter5.2 uA
Sampling frequency of this letter13.3 to 37 Hz window with 20 Hz typical
Sampling period50 to 75 ms per sample
Operate point for 63 mTplus or minus 33 to plus or minus 63 mT, 47 mT typical
Hysteresis1.2 to 8.5 mT with 4 mT typical
Output current, absolute maximumplus or minus 5 mA
Output high at 1 mAVCC minus 0.35 V maximum on the push pull version
Output low at 1 mA0.1 V typical and 0.3 V maximum
Operating temperatureminus 40 to plus 85 degrees, which rules out most under bonnet work

Family variants and how they differ

DRV5032FA4.8 mT unipolar, push pull, 20 Hz, in SOT-23, X2SON and TO-92
DRV5032FBThe same 4.8 mT threshold at 5 Hz, for the longest battery life
DRV5032FC4.8 mT omnipolar, push pull, 20 Hz
DRV5032FD4.8 mT omnipolar, open drain, 20 Hz
DRV5032DU3.4 mT unipolar push pull, X2SON only
DRV5032AJ9.5 mT unipolar, 20 Hz, SOT-23 and TO-92
DRV5032DG80 Hz sampling, 5.2 uA, for a fast target
DRV5032ZE in TO-92The active row of the same 63 mT letter, 1000 pieces on a small reel

Points to check before this part goes on a BOM

The lifecycle line on this page is the first thing to read, because the addendum marks the plain DRV5032ZEDBZR row Obsolete Production while the .A row of the same string is Active in the TO-92 body. A purchase order that names the plain string can come back as a different package, so the body has to be named on the order and the last time buy has to be planned before the distributor stock is gone.

63 mT is roughly thirteen times the threshold of the FA letter, and that is the whole reason to take this part. A door sensor with a 20 mm magnet gap, a tamper switch behind 2 mm of steel, or a valve position target that sits beside a motor housing all produce a few millitesla of wanted field and a lot more unwanted field from the bracket. The ZE letter ignores the second and still trips on the first, at the cost of a stronger magnet or a tighter gap.

The device is not a continuous comparator. An internal oscillator wakes the sensing chain 20 times a second and the output holds its state between samples, so the response to a step in field can lag by a full sampling period of 50 to 75 ms. A mechanical target that moves faster than that is aliased, and a rotating magnet with many poles can be counted wrong. The DG letter samples at 80 Hz for the cases where 20 Hz is too slow, at four times the current.

The three current figures are the whole power budget. At 1.3 uA the 20 Hz letter costs about 11 mAh a year, so an AA cell lasts longer than the product, while the 80 Hz letter at 5.2 uA costs about 46 mAh a year. The 5 Hz letter at 0.54 uA costs under 5 mAh a year. Choose the sampling rate from the mechanics first and the battery second, because dropping to 5 Hz cannot be recovered by firmware.

The output type changes the pull up and nothing else in the circuit. The push pull version drives the line in both directions and needs no resistor, while the open drain version needs a pull up to the controller rail and is the one to take when the sensor runs at 5 V and the MCU at 1.8 V. Both are published under the ZE letter, so the order code decides which one arrives and the board note has to match it.

Where a 63 mT omnipolar switch earns its place

An electronic lock or a smoke detector shutter is the classic case. The magnet is bonded into a plastic slider, the sensor sits behind a steel frame, and the field that reaches the die at the closed position is a fraction of what a bench test with the magnet against the package shows. A 4.8 mT part trips on the frame and reports closed while the door is open, which is a recall, while the 63 mT part does not.

Tamper detection in an electricity meter uses the same property from the other side. A magnet brought against the case to interfere with the meter has to be detected, and the sensor is placed where the housing already attenuates the field. A high threshold part plus a magnet on the cover gives a signal that only appears when the cover is off, and the 1.65 V floor of the supply keeps the part alive on the meter backup rail.

What the board has to provide

Three pins and one capacitor. VCC, GND and OUT, with 0.1 uF of ceramic within a few millimetres of the supply pin, because the sampling oscillator draws a short pulse that a long trace turns into a droop. The X2SON body is 1.4 mm by 1.1 mm and needs the same decoupling, and the TO-92 body is the one to choose when the sensor is potted into a probe.

The magnet side matters more than the electrical side. Omnipolar response means either pole trips the part, so a magnet can be fitted either way round, but the flux density at the die falls with the cube of the distance for a small magnet, which is why the 63 mT letter needs the gap quoted in the mechanical drawing rather than assumed. A field of 63 mT at 3 mm is a different magnet from 63 mT at 8 mm.

Where this order code fits

The part suits a battery powered position or tamper switch where the magnet gap is wide, the field has to be told apart from a nearby steel part, and the output only has to change at human speed. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the plain string still orderable? The addendum marks the DBZ row Obsolete Production and keeps the .A row of the same string Active in TO-92. Treat the SOT-23 as the end of life row, confirm the body on the order and plan a last time buy, or move the footprint to the TO-92 if the mechanics allow it.

How fast can the output follow a magnet? One sample every 50 to 75 ms, so the output changes within one period of the field crossing the threshold. Anything faster than a few hertz of target motion needs the 80 Hz letter, and even that stops at 80 samples a second.

Does it need a pull up resistor? Only the open drain version does. The push pull version drives both levels and the only external part is the 0.1 uF supply capacitor.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.