DRV5023BIQDBZRQ1
Product Specifications
DRV5023BIQDBZRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5023BIQDBZRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5023BIQDBZRQ1: the 14.5 mT unipolar switch for a wide air gap
The DRV5023BIQDBZRQ1 is the least sensitive member of the DRV5023 unipolar switch family, built in the SOT-23 body with the Q1 automotive qualifier. Its operate point is 14.5 mT and its release point is 6 mT, which is more than four times the field a 3.5 mT option needs to switch. The trade is deliberate: a bigger threshold buys distance, and distance is what a mechanical assembly usually needs.
Everything else matches the family. Supply range is 2.5 V to 38 V, the output is open drain with 30 mA of sink, reverse supply is protected to 22 V, and the part is valid 35 us after power on with a pulse to mark the transition.
The case for BI is usually packaging rather than magnetics. When the sensor has to sit behind a 3 mm wall of plastic, or when the magnet is a low grade ferrite that cannot be brought closer, the higher threshold is the only way to get a reliable transition without changing the mechanical parts.
Key data for the DRV5023BIQDBZRQ1
| Output | Open drain, 30 mA sink, active low above the operate point |
| Operate point | 14.5 mT typical on the BI option, within 10 percent over temperature |
| Release point | 6 mT typical, which leaves 8.5 mT of hysteresis |
| Supply | 2.5 V to 38 V, no regulator, reverse protection to 22 V |
| Supply current | 2.7 mA typical on the continuous bias parts of this family |
| Power-on time | 35 us typical, 70 us maximum at the temperature extremes |
| Temperature | Minus 40 C to plus 125 C on the Q grade |
Body, packing and marking data
| Body | SOT-23, three pins, DBZ outline |
| Packing | 3000 pieces on a large reel, 180 mm reel diameter, 8.4 mm tape width |
| Finish | Nickel palladium gold and tin on the split rows, so the finish has to be read per row |
| Status | Active on the addendum, with the A revision row carrying the moisture level and floor life |
What the suffix tells you and what it does not
The string is DRV5023, BI sensitivity, Q temperature, DBZ body, R large reel, Q1 automotive. The addendum prints BIQDBZR and BIQDBZT as active industrial rows at 3000 and 250 pieces, and it also prints the LPG through-hole rows in ammo and bulk, so the family is fully documented in both bodies.
The Q1 on the end is the one field the addendum does not print for this body. That is normal for automotive grades, which are released under a separate part number series in some programs, and abnormal only when a buyer assumes the reel label will match the industrial row. We recommend the grade be written into the purchase order text rather than left to the suffix, and the incoming label checked against that text when the first reel arrives.
There is also a practical point about the hysteresis. At 8.5 mT the gap between operate and release is wide, which is what stops chatter on a vibrating panel, but it also means a slowly moving magnet produces a late release. On a valve that closes at a slow rate, the release can lag the mechanical stop by a visible margin.
Where the BI option earns its place
Doors and lids on outdoor cabinets, docking cradles with a thick plastic shell, valve position on a brass body and proximity sensing through a metal shield are the cases where a 14.5 mT threshold is the difference between a working assembly and a rejected one. Pulse counting on a coarse target is the other, because a big magnet on a slow shaft does not need sensitivity, it needs to ignore stray fields.
For boards that mix this switch with other position sensors, the IMU selection guide sets out where a discrete Hall switch is still the better answer than an inertial part, and the incoming inspection plan page covers the field test that catches a wrong sensitivity option before it reaches the line.
Questions we get on this code
Can a 14.5 mT part replace a 6.9 mT part on the same magnet? Only if the field at the sensor face is measured first. A magnet that produces 8 mT at the current gap will not operate the BI part at all, and the failure looks like a dead sensor rather than an unsuitable one.
What about the supply? The family runs to 38 V, so on a 24 V rail with load dump the part survives without a clamp. On a 5 V logic rail the same part works, and the pull up can go to 3.3 V or 5 V independently of the supply, which is what allows a 24 V sensor to talk to a 3.3 V controller.
One more point on the body. The BI die is also published in the TO-92 with an ammo or bulk packing, and a through-hole part is often the only way to reach a sensor socket on an older assembly. The electrical behaviour is identical, so the body choice is a mechanical decision rather than an electrical one, and the reel or ammo count follows from it.