Contact Us

DRV5023BIEDBZRQ1

Brand: Texas Instruments
Texas Instruments DRV5023BIEDBZRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV5023BIEDBZRQ1 — Power Management & Signal Chain | Superb Automation

DRV5023BIEDBZRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV5023BIEDBZRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV5023BIEDBZRQ1: A 14.5 mT Unipolar Hall Switch That Holds Its Trip Point Over Temperature

DRV5023BIEDBZRQ1 is a chopper stabilised unipolar Hall effect switch with an open drain output in a SOT-23 (DBZ) body of 3 pins. It runs from 2.5 V to 38 V without an external regulator, sinks 30 mA on the output, and switches in 35 us from power on. The BI sensitivity option on this order code trips at 14.5 mT and releases at 6 mT, which is a wide window for a magnet that has to work through a plastic wall or an air gap. The chopper stage holds the trip point to plus or minus 10 per cent over the full temperature range, which is the number that decides whether a door sensor still reports closed at minus 40 degrees.

Order code and package

Ordering stringDRV5023BIEDBZRQ1, SOT-23, large reel
Family documentDRV5023, SLIS151G, May 2014, revised September 2016
Sensitivity codeBI, operate point 14.5 mT, release point 6 mT
PackageSOT-23 (DBZ), 3 pins, 2.92 mm by 1.30 mm body
Ambient rangeminus 40 to plus 125 degrees, Q grade
Junction rangeminus 40 to plus 150 degrees
Storage rangeminus 65 to plus 150 degrees
PinsVCC, OUT, GND, with the tab on the package face toward the magnet
Output typeopen drain, needs a pull up resistor to VCC
Sibling packagesLPG TO-92 through hole, same die, 4.00 mm by 3.15 mm

Electrical parameters that decide the application

Supply range2.5 to 38 V, no series regulator needed
Absolute maximum supply40 V, reverse to minus 22 V
Supply current2.7 mA typical at 25 C, 3 mA typical at 125 C
Power on time35 us, output valid after that
Output sink30 mA during recommended operation
On resistance of the output FET22 Ohm at 3.3 V and 10 mA, 50 Ohm maximum at 125 C
Off state leakage1 uA when the output is high impedance
Operate point, BI option14.5 mT maximum, typical 12 mT
Release point, BI option6 mT minimum, typical 8 mT
Hysteresisthe gap between the two points, roughly 4 mT on BI
Output delay13 us typical, 25 us maximum into a 50 pF load
Output rise and fall200 ns rise, 31 ns fall with a 1 kOhm pull up
Overcurrent clamp15 to 45 mA when the output is shorted to VCC
Junction to ambient, SOT-23333.2 C per W
ESD, human body modelplus or minus 2500 V

Family variants and how they differ

DRV5023FA3.5 mT operate, 2 mT release, the sensitive option for small magnets
DRV5023AJ6.9 mT operate, 3.2 mT release, the middle option
DRV5023BI14.5 mT operate, 6 mT release, the part on this page
DRV5013bipolar latch, needs a field reversal to change state
DRV5053analogue output, gives field strength rather than a switched state
DRV50321.65 V to 5.5 V, microamp class current, lower magnetic range
What changes between optionsonly the magnetic window, the die and the pins stay the same
What does not changesupply range, output drive and protection behaviour

Points to check before this part goes on a BOM

The BI window is chosen for mechanical tolerance rather than for sensitivity. A 14.5 mT operate point needs a stronger magnet than the FA option, but it forgives a much larger air gap and a much wider mounting tolerance, because the field has to fall all the way to 6 mT before the output releases. On a door or a flap that is what stops chatter when the panel vibrates. The trade is that the magnet has to be sized for the worst case gap at the coldest temperature, where a ferrite magnet loses roughly a fifth of its flux compared with 20 degrees, and that sizing is what decides whether the part is the right choice at all.

The chopper stabiliser is the reason the trip point survives temperature. The device samples the Hall plate, reverses the bias, and subtracts the two measurements, which cancels the offset drift of the plate itself. What remains is the drift of the threshold comparator, and the data sheet bounds the whole effect at plus or minus 10 per cent of the operate point over the temperature range. In practice that means a 14.5 mT part behaves like a 13 to 16 mT part at every temperature, so the mechanical budget can be built around a single number instead of a curve, which is the difference between a sensor that can be qualified in a week and one that needs a chamber run at three temperatures.

The output is an open drain FET and the pull up sets the rise time. With a 1 kOhm resistor to a 3.3 V rail the rise time is 200 ns and the fall time is 31 ns, because the FET pulls the line down actively while the resistor has to charge the capacitance through the same 1 kOhm. The data sheet gives an allowed resistor window from 113 Ohm to 32 kOhm for a 3.3 V system, bounded at the low end by the 30 mA sink rating and at the high end by the 1 uA leakage of the off state. A 10 kOhm pull up is the usual compromise: it draws 330 uA while the output is low, which is acceptable in a battery product, and it still gives a rise time below 10 us into 50 pF, fast enough for a mechanical event that lasts milliseconds.

Protection is built in and it changes what the board does not need. The device survives a reverse supply of minus 22 V, a 40 V load dump, and a shorted output, and it clamps the output current at roughly 30 mA instead of letting the FET cook. On a 24 V industrial rail that removes the series resistor and the clamp diode that a bare Hall switch would need, and it removes the field failure mode where a harness short takes out the sensor and the input pin behind it. The reverse protection is specified by characterisation and tested to minus 20 V, so an engineer who expects repeated reverse events should still add the series diode, but a single miswired connector at installation is covered.

Where this order code fits

These switches turn up in docking stations, door and flap detection, valve position sensing and pulse counting on a rotating target. A team that needs the same function on a 12 V or 24 V harness without a regulator starts from the 38 V supply range rather than from the sensitivity. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can the output drive a relay directly? No. It sinks 30 mA and clamps at roughly 30 mA, so it drives a logic input or a small LED through a resistor, and a relay needs a transistor or a low side driver behind it.

Does the part need a pull up on a 5 V rail? Yes, and the resistor has to keep the current below 30 mA at 5 V, so 220 Ohm is the practical floor and 10 kOhm the usual value.

Is the automotive grade the same die as the industrial part? The Q grade is the same function with the ambient range guaranteed to 125 C and the automotive flow behind it, so the magnetic window and the pins are identical.

What happens if the magnet is too weak at cold? The output simply stops switching. There is no partial state. That is why the operate point is checked at the coldest temperature with the largest gap, not at room temperature on a bench.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.