DRV5013BCQLPGM
Product Specifications
DRV5013BCQLPGM
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5013BCQLPGM from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5013BCQLPGM: a 12 mT bipolar latch in a through-hole body
The DRV5013BCQLPGM is a chopper stabilised bipolar Hall latch in the three pin TO-92 body, the through-hole option of a part that most boards use in SOT-23. It runs from 2.5 V to 38 V with no external regulator, sinks 30 mA on an open drain output, and carries reverse supply protection to 22 V plus load dump and output short circuit protection. For a 12 V or 24 V rail the part can hang straight off the supply with a single pull up resistor.
BC is the least sensitive option in the group. The operate point is 12 mT, the release point is minus 12 mT, and the gap between them is 24 mT of hysteresis. That tolerance of 10 percent holds over the whole temperature range, which is the reason the family is chopper stabilised: the offset of the Hall element is sampled out continuously instead of being trimmed once.
A latch is not a switch. It changes state only when the field crosses from one polarity to the other, so it reports shaft position rather than field presence, and it keeps that state after the magnet has moved away. Bandwidth is 30 kHz typical, so a ring magnet on a motor shaft at a few thousand rpm is well inside the response of the part.
Key data for the DRV5013BCQLPGM
| Output | Open drain, active low, 30 mA sink |
| Operate point | 12 mT typical for the BC option, within 10 percent over temperature |
| Release point | Minus 12 mT, which gives 24 mT of hysteresis |
| Supply | 2.5 V to 38 V, no external regulator needed, reverse protection to 22 V |
| Supply current | 2.7 mA typical at 25 C across the whole supply window |
| Bandwidth | 30 kHz typical, which is the fastest field change the part follows |
| Temperature | Minus 40 C to plus 125 C on the Q code, minus 40 C to plus 150 C on the E code |
Body, packing and marking data
| Body | TO-92, three pins, the LPG body |
| Packing | 3000 pieces in ammo pack on the M suffix row |
| Finish | Tin lead finish, moisture level not applicable to a through-hole body |
| Marking | NLBC on the flat face, which is the BC sensitivity code |
Reading the code before you buy it
Read the string from the left. DRV5013 is the family, BC is the sensitivity, Q is the temperature grade, LPG is the TO-92 body, and M is the ammo pack. The same code with no M and no R is a 1000 piece bulk bag, and with an R it is the 3000 piece reel in SOT-23, so the last letter decides both the body and the packing.
One thing to settle in writing is the temperature grade. The orderable addendum prints this exact string twice, once as a 3000 piece ammo row and once as a 1000 piece bulk row, and the two rows disagree on the operating range, one printing minus 40 to plus 150 C and the other minus 40 to plus 125 C. The Q in the code decodes as 125 C on the nomenclature page. A purchase order that has to survive an audit should name the grade explicitly instead of leaning on the suffix alone.
The second point is the magnet. A 12 mT operate point is roughly four times the level of the 2.7 mT option, so the magnet that worked with an AD part will not necessarily switch a BC part at the same air gap. Either close the gap or move up a magnet grade, and check the field at the marked face rather than at the magnet surface.
Where this latch earns its place
Brushless dc motors use a latch per phase to read rotor position, flow meters count pulses from a paddle magnet, and valve or solenoid assemblies use the latch as an end of travel indicator that keeps its state after the actuator has stopped. Tachometers and power tool triggers are the other two applications the vendor lists.
When a board is being reworked around a part that has gone short, the pin to pin cross reference page covers what has to match before a substitute latch is accepted, and the component lead time solutions page sets out the steps for qualifying a second body when the SOT-23 is the constrained one.
Questions we get on this code
What happens if the board powers up with the magnet sitting between the two thresholds? The data sheet answers this directly: inside the band the output is indeterminate and can come up either high impedance or pulled low, and a pulse appears on the output at the end of the 35 us power-on time to tell the controller when the state is valid. If the application cannot tolerate that, the controller has to command a field excursion at start up or the magnet has to be parked outside the band.
Which pole triggers it? A south pole at the marked face is a positive field, so a south pole above 12 mT pulls the output low and the output only releases when a north pole of at least 12 mT arrives. A board that waves the same pole past the part repeatedly will see one transition and then nothing, which is the most common reason a latch is reported as dead.