Contact Us

DRV5011ADLPGM

Brand: Texas Instruments
Texas Instruments DRV5011ADLPGM is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV5011ADLPGM — Power Management & Signal Chain | Superb Automation

DRV5011ADLPGM

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV5011ADLPGM from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV5011ADLPGM: the same latch die in a through hole body

The DRV5011ADLPGM is the three pin TO-92 member of the DRV5011 latch family, supplied in bulk rather than on tape. The die inside is the same low voltage latch that runs from 2.5 V to 5.5 V, with plus or minus 2 mT typical sensitivity, about 4 mT of hysteresis, a 30 kHz sampling rate and a push pull output that needs no pull up. What changes with this body is how the part is handled, not what it measures.

Through hole sensing still has a place. A motor housing that was built around a leaded sensor, a harness that ends in a three pin connector, a repair bench that cannot reflow a SOT-23 and a jig that presses the sensor into a slot all point at the same package. The TO-92 lead frame also puts the sensing element further from a noisy board, which is worth something on a motor with a switching drive a few millimetres away.

The temperature window on this row is the detail to check. The addendum prints minus 40 C to plus 125 C for the TO-92 rows, against minus 40 C to plus 135 C for the SOT-23 row of the same family. A board that was qualified at 130 C on the surface mount body has to be re checked before the leaded body is substituted, even though the magnetic behaviour is identical.

Key data for the DRV5011ADLPGM

TypeDigital latch, toggles on alternating north and south poles
SensitivityOperate point plus or minus 2 mT typical, about 4 mT of hysteresis
Supply2.5 V to 5.5 V, no external regulator required
OutputPush pull CMOS, 5 mA source and 20 mA sink, no pull up needed
Bandwidth30 kHz sampling rate
TemperatureMinus 40 C to plus 125 C on the TO-92 rows of the addendum

Body, packing and marking data

BodyTO-92 LPG, 3 leads, 4.00 mm by 3.15 mm, leaded and not surface mount
Packing1000 pieces in bulk, no tape and no reel
FinishTin plated leads, moisture level recorded as not applicable for this package type
TemperatureMinus 40 C to plus 125 C, marking 11AD on the published row

Order code note before you place the string on a purchase order

Bulk packing changes the counting rules. A 1000 piece bag is not a reel, so an assembly house that feeds from tape has to hand load or re tape, and a machine that verifies reel identity will have nothing to verify. The M at the end of this string marks the bulk option, and the same die in tape is the SOT-23 string rather than a taped version of this one.

The moisture level field reads not applicable because a leaded part with tin plated leads is not a moisture sensitive device in the same sense as a plastic body surface mount part. That does not mean it can sit open in a humid room for a year, but it does mean the bake rules that apply to the reel parts on the same board do not apply here.

Where a leaded latch earns its place

Motor housings with a moulded pocket, pump bodies with a connector, and retrofit work on equipment that was built before surface mount took over all use a leaded sensor. The 2 mT sensitivity and 30 kHz bandwidth behave exactly as they do in the small body, so the electrical behaviour a controller sees does not change when the package does.

Substituting a leaded part for a surface mount one is a mechanical change with electrical consequences, and it usually arrives as a line down situation. Our BOM shortage recovery page covers how a package change is qualified in a short window, and the how to verify a drop in replacement page sets out the checks that separate a real drop in from a part that looks close enough.

Questions we get on this code

The first question is whether the leaded body is a drop in for the surface mount one. It is not, because the footprint is different, the leads have to pass through the board and the sensing element sits at a different height above the board. The electrical specification carries over and the mechanical position of the magnet does not.

The second question is about lead forming. The LPG lead frame has one bend already applied, and a second bend to fit a different height changes the stress on the package and can crack the die attach. If the application needs a different lead shape, order the LPE variant rather than bending this one on the bench. On a motor with three sensors, all three leads have to be formed the same way, and hand forming is where a set of three stops being a set of three.