Contact Us

DRV2605YZFR

Brand: Texas Instruments
Texas Instruments DRV2605YZFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV2605YZFR — Power Management & Signal Chain | Superb Automation

DRV2605YZFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV2605YZFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV2605YZFR: An I2C Haptic Driver That Plays Stored Effects Instead of Streaming Waveforms

DRV2605YZFR is a haptic driver for eccentric rotating mass motors and linear resonant actuators with a licensed effect library in a DSBGA (YFF) body of 9 pins. It runs from 2.5 V to 5.5 V, sits on a shared I2C bus, and holds a licensed library of more than a hundred effects from Immersion, so the host writes a register instead of generating a waveform. The output stage is trinary modulated, which is more efficient than a linear driver, and a back EMF sensing loop tracks the resonance of a linear actuator and applies overdrive and braking automatically. The 9 ball package is 1.50 mm by 1.50 mm, which is the reason it appears in phones and watches.

Order code and package

Ordering stringDRV2605YZFR, DSBGA, large reel
Family documentDRV2605, SLOS825E, December 2012, revised April 2018
PackageDSBGA (YFF), 9 balls, 1.50 mm by 1.50 mm
Supply range2.5 to 5.5 V
BusI2C, address 0x5A, 1.8 V compatible pins
Effect librarylicensed Immersion TouchSense 2200, over 100 effects
Actuator supportERM and LRA, with auto resonance for the LRA
Regulator pinREG at 1.84 V, needs a bypass capacitor
InputsPWM or analogue on the IN/TRIG pin, plus a hardware trigger
SiblingDRV2605L, same function with a lower supply floor for small cells

Electrical parameters that decide the application

Supply voltage2.5 to 5.5 V, absolute maximum 6 V class
Quiescent currentabout 1 mA in operation with the output idle
Shutdown current1.75 uA typical, 4 uA maximum
Standby current1.9 uA typical, 5 uA maximum
REG pin voltage1.84 V typical, bypassed to ground
Logic high threshold1.3 V, so a 1.8 V bus drives it directly
Logic low threshold0.5 V
Minimum load impedance8 Ohm
LRA frequency rangethe driver tracks the actuator resonance within its window
PWM input frequency10 to 250 kHz
Output stagetrinary modulated, no output filter inductor
Auto calibrationoffset and back EMF calibrated per actuator at start up
Shutdown output impedance15 kOhm to ground on each output
Thermal and overcurrentinternal shutdown with a fault register

Family variants and how they differ

DRV2605I2C, licensed library, auto resonance, the part on this page
DRV2605Llower supply floor and a reduced library for small cells
DRV2604I2C with a RAM waveform store, no licensed library
DRV2604Lthe low voltage member of the RAM store version
DRV2603PWM and enable only, auto resonance, no bus
DRV8601PWM input, no library and no tracking, the simplest member
What the library changesthe host no longer stores or streams waveforms
What the closed loop changesthe actuator is calibrated per unit and the resonance tracked

Points to check before this part goes on a BOM

The licensed library is the reason to pay for this part rather than a plain driver. Each effect is a stored waveform with a defined attack, sustain and brake, tuned for the actuator class, and the host selects one by index over I2C. That removes the audio or haptic waveform from the firmware image, removes the timing jitter of a software PWM, and makes the feel consistent across products. The library is licensed, so the terms travel with the part rather than with a separate agreement, which is why an engineering team can use it without a legal negotiation and why the same effect sounds the same on two different phone models if the actuator is comparable.

The smart loop closes the control around the actuator instead of around the drive voltage. At start up the device measures the back EMF of the actuator and calibrates the resistance and the inductance, then during playback it uses that model to apply overdrive at the leading edge and active braking at the trailing edge. On an eccentric rotating mass motor this shortens the spin up and stops the tail, which is what makes a 20 ms click feel crisp. On a linear actuator it tracks the resonance, which drifts with temperature and with mechanical loading, and keeps the amplitude constant as the battery voltage falls.

Auto resonance is the feature that decides between this part and a fixed frequency driver. A linear resonant actuator has a resonance that moves by a few hertz between units and by more than that over temperature, and driving it off resonance produces a weak and slightly delayed response. The tracking loop sweeps the drive frequency, watches the back EMF phase, and locks to the peak, which is done continuously rather than at calibration. The price is that the actuator has to be characterised once on the bench with the intended mounting, because the loop needs a sane starting point and a mount that damps the resonance heavily will defeat it.

The 1.5 mm package and the 1.8 V compatible bus are what make the part fit a phone, and they also set the constraints. The 9 ball array needs a via in pad or a very short trace to the bypass capacitor on REG, which is 1.84 V and not a supply, so it must not be loaded. The shutdown current of 1.75 uA is low enough to leave the part powered between events, and the standby state keeps the calibration, so the first effect after wake is as strong as the tenth. A product that cuts the supply to save current loses the calibration and pays a fresh start up every time, which is visible as a weaker first click.

What has to be measured on the bench before release

Three measurements decide whether the haptic output will feel right in the product. The first is the actuator resistance and inductance, read by the calibration step and reported in registers, because a unit that reads far outside the batch average points at a wrong actuator or a bad solder joint. The second is the resonance frequency of a linear actuator in its final mount, which has to fall inside the tracking window of the driver, and which shifts when the mount is tightened. The third is the amplitude at the lowest battery voltage the product will see, because the trinary output stage loses strength as the supply falls and an effect tuned at 4.2 V can be noticeably weak at 3.4 V. All three are read over I2C and can be logged in the factory test step without extra fixtures.

Where this order code fits

Touch feedback in phones, tablets, watches, remote controls and automotive panels, where the effect has to feel the same on every unit. A team that wants a defined click without storing waveforms starts from the library; a team with its own waveforms uses the RAM store version. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it drive two actuators? No, there is one differential output pair. Two actuators need two devices on the same bus, which is possible because the address is fixed per part and would then need a bus switch.

Does the host have to generate any waveform? No, it writes an effect index and a duration. The real time playback mode is available when the host wants to stream its own samples.

What happens if the actuator is not connected? The diagnostic and calibration step reports a fault in the status register, and playback produces no output rather than an overcurrent event.

Is the library usable in a medical product? The licence terms come with the part, but the actuator and the effect have to be validated in the end product regardless of the driver, so the answer depends on the product file.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.