Contact Us

DRV11873PWPR

Brand: Texas Instruments
Texas Instruments DRV11873PWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV11873PWPR — Power Management & Signal Chain | Superb Automation

DRV11873PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV11873PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV11873PWPR: A 12 V Sensorless Fan Driver With the Commutation Logic Inside

DRV11873PWPR is a three phase sensorless brushless motor driver with integrated FETs in a HTSSOP (PWP) body of 16 pins. It takes a PWM input between 7 kHz and 100 kHz, commutates a three phase motor from back EMF with a 150 degree scheme, and delivers 1.5 A continuous and 2 A peak from 5 V to 16 V with no position sensor and no external shunt. The speed is reported on an open drain FG pin and a locked rotor on an RD pin, which is everything a cooling fan controller needs to know.

Order code and package

Ordering stringDRV11873PWPR, large reel, 2000 pieces
Family documentDRV11873, SLWS237A, revised November 2014
PackageHTSSOP (PWP), 16 pins with PowerPAD, 4.40 mm by 5.00 mm
Lead finishNIPDAU
Moisture levelLevel 2, 260 C, one year floor life
Body marking11873
Ambient range on the addendumminus 40 to plus 85 degrees
Junction range in the electrical tableminus 40 to plus 125 degrees
Rows of the same stringDRV11873PWPR.A, active, same reel and marking
Companion pinsPWMIN, FS, FR, CS, FG, RD, V5 and COM

Electrical parameters that decide the application

Supply range5 to 16 V
Continuous output current1.5 A
Peak output current2 A
FET resistance high plus low0.45 Ohm typical, 0.6 Ohm maximum at 1.5 A
PWM input frequency7 to 100 kHz
PWM input current35 to 65 uA, 50 uA typical
Commutation150 degree sensorless back EMF, synchronous rectification
Current limit settingexternal resistor on CS, 3.3 kOhm gives 1.7 to 2.3 A
Internal regulator5 V at up to 20 mA for external use
Undervoltage lockout4.3 to 4.6 V rising, 3.9 to 4.1 V falling
Supply current2.7 to 5 mA at 12 V and 25 C
Speed outputFG, open drain, frequency scaled by the FS pin
Lock outputRD, open drain, asserted when the rotor does not turn
Junction to ambient39.4 C per W in the PWP body

Family variants and how they differ

DRV1187312 V class, 1.5 A, sensorless, the part on this page
DRV1098312 to 24 V, 2 A, with EEPROM settings and I2C
DRV1098712 to 24 V, 2 A, integrated buck, sinusoidal control
DRV11873 against thoseNo configuration memory and no bus, so the settings are pins
FS pinScales the reported speed frequency by a factor of two
FR pinSelects the forced commutation behaviour at start up
V5 pin5 V output for a hall sensor or a controller, 20 mA maximum

Points to check before this part goes on a BOM

The point of this part is the absence of a sensor and of a shunt. Back EMF is measured on the phase that is not driven, the commutation angle is derived from it, and the current limit comes from the internal sense rather than an external resistor, so a fan driver becomes a 16 pin part with a PWM input and two status outputs. A board that has a microcontroller and wants to close the loop itself should not use this part, because the commutation is not accessible.

Start up is the hard part of a sensorless scheme and this part handles it with forced commutation. At zero speed there is no back EMF to measure, so the part drives a ramp until the rotor follows, and the FR pin sets how that ramp behaves. A fan with a heavy impeller needs a longer ramp than a bare rotor, and a fan that starts against a pressure load needs more current for longer, which is why the CS resistor is chosen from the worst case start rather than from the running current.

The 5 V regulator is 20 mA and it is not a system supply. It exists to power a hall sensor in a fan that has one, or a small controller, and it is derived from the same charge pump that drives the high side gates. Loading it with a relay coil or a display pulls the gate drive down and produces the symptom of a motor that runs at low speed but stalls at full PWM.

The two temperature figures on the datasheet disagree in a way that matters for a purchase order. The addendum prints the ambient range as minus 40 to plus 85 degrees, while the electrical table specifies junction conditions to 125 C and the description mentions operation to 125 C. A fan inside a server that sees 70 C inlet air is inside the ambient rating, and a fan in a sealed enclosure at 90 C is not, however the junction is described.

What the FG and RD pins tell a controller

FG is a square wave at the commutation rate, so a controller that counts edges gets speed without a tachometer wire, and the FS pin doubles or halves the reported frequency for a controller with a narrow input range. RD is a locked rotor flag that asserts when the commutation does not advance, which is the signal a system uses to decide between a retry and a shutdown.

Neither output is a fault log. An overcurrent trip, a thermal shutdown and a supply brownout all present as a stopped motor with RD asserted, so a controller that needs to distinguish them has to look at the supply current and the temperature itself. That is the price of a part with no bus and no registers.

The current limit resistor is the component that has to be right at start up rather than at running speed. A fan that draws 400 mA once it is turning can pull 1.5 A for the first few hundred milliseconds, and a limit set at 800 mA will stall it every time. The resistor is chosen from the start up current, which means the running current sits well below the limit and the internal protection only intervenes on a genuine jam.

The 5 V rail on the V5 pin is worth a second look before it is used for anything but a sensor. It is derived from the same charge pump that drives the high side gates, it is rated at 20 mA, and it is not protected against a short in the way a system regulator would be. A board that powers a hall sensor from it is fine, and a board that powers a relay coil from it drops the gate drive every time the coil pulls in.

Where this order code fits

Fan and pump projects that need speed feedback without a sensor start from the power management cross reference page Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Can the PWM input be driven from 3.3 V logic? Yes. The input threshold is 2.3 V high and 0.8 V low above a 4.5 V supply, and the pin sources about 50 uA, so a 3.3 V push pull output drives it directly. An open drain output needs a pull up to the 5 V rail or to V5.

What sets the maximum motor current? The CS resistor. A 3.3 kOhm resistor gives a 1.7 to 2.3 A limit, and the value scales inversely with the wanted current. The internal limit protects the FETs, and the external resistor sets the point at which the part starts limiting rather than tripping.

Does it need a minimum load to start? It needs a rotor that can follow the forced commutation ramp. A fan with a broken blade or a pump with a dry seal may not, and the part reports a locked rotor on RD rather than continuing to push current into a stationary winding.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.