Contact Us

DRV10964FFDSNR

Brand: Texas Instruments
Texas Instruments DRV10964FFDSNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV10964FFDSNR — Power Management & Signal Chain | Superb Automation

DRV10964FFDSNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV10964FFDSNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV10964FFDSNR: A 5 V Sensorless Sinusoidal Driver for Small Fans and Blowers

DRV10964FFDSNR is a three phase sensorless BLDC driver with the bridge inside in a USON (DSN) body of 10 pins. It runs from 2.1 V to 5.5 V, delivers up to 500 mA, and commutes a small three phase motor with a windowless 180 degree sinusoidal scheme that keeps the acoustic signature low. Total high side plus low side resistance stays under 1.5 Ω at half an amp, sleep current is 15 uA, and the part measures the motor resistance and torque constant on every start so that no configuration memory is needed.

Order code and package

Ordering stringDRV10964FFDSNR
Family documentDRV10964, SLDS227, March 2016
PackageSON (DSN), 10 pins, 3.00 mm by 3.00 mm with an exposed pad
Reel and packing3000 pieces on a large reel, NiPdAu lead finish
Moisture levelLevel 2, 260 C peak, one year floor life
Body marking964FF1
Temperature rangeminus 40 to plus 125 degrees
Small reel siblingDRV10964FFDSNT, the same die, 250 pieces on a small reel
Control pinsPWM input, FG speed output, FR direction, FGS status, CONFIG handoff level
Configuration storageNone. The part measures resistance and torque constant at each start
BridgeIntegrated, three phase, no external FETs

Electrical parameters that decide the application

Supply range2.1 to 5.5 V
Output current500 mA
Bridge resistance1.0 Ω typical and 1.5 Ω maximum for high side plus low side at 0.5 A
Operating current6.5 mA typical with the PWM input high and no motor connected
Sleep current15 uA typical and 20 uA maximum
Sleep entry1 ms after the PWM input goes low with the motor below 10 Hz
UndervoltageHigh threshold 2.0 to 2.1 V, low threshold 1.8 V, 200 to 300 mV of hysteresis
PWM inputThresholds at 0.15 and 0.45 of VCC, accepted up to 100 kHz
BEMF comparator10 mV of input offset, 21 to 28 mV of hysteresis, 1.5 us of output delay
Align sequence0.64 s of alignment at 50 per cent duty, reached through a 300 ms ramp
Initial speed detect80 ms without a comparator edge is treated as a stationary rotor
Calibration time40 ms at power on before the align state

Family variants and how they differ

CONFIG 0x0Handoff at 87.5 Hz for motors whose top speed is 350 to 400 Hz
CONFIG 0x4Handoff at 50 Hz for motors between 150 and 200 Hz
CONFIG 0xCHandoff at 150 Hz for motors between 620 and 700 Hz
CONFIG 0xFHandoff at 187.5 Hz for motors above 900 Hz
FR pinDirection, sampled as a logic level with the same 0.15 and 0.45 of VCC thresholds
FG pinSpeed output, one pulse per electrical revolution, 13 to 25 mA of sink current
FGS pinStatus output with an internal pull up, 40 kΩ in active mode
PWM dutyAnything above zero and below 100 per cent is accepted, the duty sets the applied voltage

Points to check before this part goes on a BOM

The start sequence is the part of the specification that decides whether a fan turns at all. After 40 ms of calibration the part aligns the rotor for 0.64 s, measures resistance and torque constant, then accelerates in open loop until the speed reaches the level set on the CONFIG pin, at which point control hands over to closed loop. A motor with a heavy impeller or a high friction bearing may not survive the open loop acceleration, and the CONFIG level is the only knob the board offers.

The handoff level is set by a resistor divider on the CONFIG pin, not by a register. Sixteen levels are available between 12.5 Hz and 187.5 Hz, and the vendor table ties each level to a range of motor top speeds. Choosing a level that is too high leaves the motor accelerating in open loop for longer than necessary, which is where stall and reverse rotation events come from, while a level that is too low hands over before the back EMF is large enough to be read reliably.

Because there is no memory in the part, every start repeats the measurement. That is what makes the device usable across a family of fans without programming, and it is also why a cold motor and a warm motor can behave differently: winding resistance moves with temperature, and the measurement is taken before the winding has warmed. A fan that starts reliably on a bench at room temperature can still fail the first start at minus 20 degrees, where the bearing torque and the winding resistance are both higher.

The 500 mA rating is a bridge rating and it comes with a thermal bill. At the 1.5 Ω maximum resistance the bridge dissipates a large fraction of a watt at half an amp, and the 3 mm by 3 mm body has to get that heat into the board through the exposed pad. A fan that draws 500 mA continuously at 85 degrees ambient is outside what the package can hold, even though the current is inside the electrical rating.

Sleep is entered on the PWM input, not on a separate enable pin. Holding PWM low with the motor below 10 Hz for 1 ms takes the part to 15 uA, which is what allows a notebook fan rail to stay connected to the battery. Waking up is a PWM edge, and the 40 ms of calibration runs again, so a system that toggles the fan every few hundred milliseconds spends a large share of its time in the start sequence.

Where this driver sits in a thermal budget

A notebook CPU fan or a projector blower is a three phase motor of a few watts, and the acoustic target is usually the hardest requirement. The windowless sinusoidal scheme removes the commutation steps that a six step drive produces, which is why the part is chosen over a cheaper trapezoidal driver even though both can turn the same motor. The cost is a start sequence that has to be tuned per motor family through the CONFIG divider.

The other half of the thermal story is the pad. The exposed pad is the only path with meaningful area, so the copper under it, the number of vias into the ground plane and the airflow over the board all decide the real current capability. A board that treats the pad as a signal ground and connects it with a single trace will run the die hotter than the ambient rating assumes.

What the part does not provide

There is no serial interface, no register map and no way to read back the measured resistance or the torque constant. A host that wants to know whether the motor started has to watch the FG output or the FGS status pin, and a host that wants a different acceleration profile has to change the PWM ramp it sends. Speed control is closed inside the part against the applied voltage, not against a commanded speed in hertz.

Current limit, short circuit protection, lock detection and thermal shutdown are all internal, and none of them reports a code. The FGS pin gives a status level and the FG pin stops toggling when the rotor stalls, so diagnostics beyond that have to come from the host measuring the two pins over time.

Where this order code fits

The part is chosen for a small three phase fan or blower on a 3.3 V or 5 V rail where acoustic noise and component count both matter, and where the motor family is fixed enough to tune one CONFIG level. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Does the motor need Hall sensors? No. The part reads back EMF through phase comparators, detects the initial speed, aligns the rotor and then runs closed loop. That is why there are only ten pins and no sensor inputs, and why the start sequence takes the better part of a second.

Can the output current be raised above 500 mA? No, and the limit is thermal rather than electrical. The bridge resistance is already 1.5 Ω at maximum, so above half an amp the package cannot pass the heat into the board. A larger motor needs a driver in a bigger body with external FETs.

What sets the point where closed loop takes over? A resistor divider on the CONFIG pin selects one of sixteen handoff frequencies between 12.5 Hz and 187.5 Hz. The vendor table relates those levels to motor top speed, and the level has to be chosen per motor family, because the part has no memory to store it.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.