Contact Us

CD4072BE

Brand: Texas Instruments
Texas Instruments CD4072BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4072BE — Power Management & Signal Chain | Superb Automation

CD4072BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4072BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4072BE: the dual four input OR gate in the 14-lead plastic DIP

The CD4072BE is the plastic dual in line entry for the CD4072B, two independent four input OR gates in a 14-lead body. The vendor page lists the device as ACTIVE with the descriptor 2-ch, 4-input, 3-V to 18-V OR gates, a drive of 6.8 mA in both directions, an 8 Mbps data rate and an operating range of minus 55 to plus 125 degrees. The tube row is 25 pieces with a nickel palladium gold finish, and the marking is CD4072BE.

Two four input gates in fourteen leads means six of the pins are inputs and two are outputs, with the rest split between the two rails. That pin count is why the part survives in boards that need a wide OR function and have no room for two quad gates and an external combine. The same document also covers the CD4071B and the CD4075B, so the addendum rows for all three appear together and a buyer reading it has to pick the right family before picking the body.

The CD4072B rows as the addendum publishes them

Part classTwo independent four input OR gates
Vendor descriptor2-ch, 4-input, 3-V to 18-V OR gates
Vendor statusACTIVE, catalogue rating
Data sheetSCHS054 family document, acquired from Harris Semiconductor
Package addendum date18 September 2026
Supply range3 V to 18 V, 20 V type rating in the headline
Output drive6.8 mA sink and source at 15 V
Data rate8 Mbps in the parametric table
Propagation delay60 ns typical at 10 V
Input current1 microamp at 18 V over temperature, 100 nA at 25 degrees
Noise margin1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V
PDIP body14 leads, 181.42 square millimetres, 19.3 by 9.4 mm
PDIP rowsCD4072BE and CD4072BE.A, 25 pieces each, Active
SOIC tube rowCD4072BM, Obsolete, blank quantity, Call TI
SOIC reel rowCD4072BM96, 2500 pieces, Active
Small reel rowCD4072BMT, 250 pieces, Obsolete
SOP reel rowCD4072BNSR, 2000 pieces, Active
TSSOP tube rowCD4072BPW, 90 pieces, Active
Ceramic rowsCD4072BF and CD4072BF3A, 25 pieces, Active
Military marking7706002CA on the F3A row
Family companionsCD4071B quad OR and CD4075B triple three input OR on the same document

This family is unusual in the CD4000B catalogue because the surface mount tube row is the one that closed while both reels stayed. The SOIC tube CD4072BM is gone, the 250 piece small reel is gone, and the 2500 piece reel and the 2000 piece SOP reel are both live. A customer who needs a hundred pieces for a pilot therefore has to take a partial reel or move to the 90 piece TSSOP tube, which is the only tube format in the family that is still active on the surface mount side.

What the parametric table fixes

Each gate takes four inputs and the two gates share a supply of 3 to 18 V, with parametric ratings at 5, 10 and 15 V. Drive is 6.8 mA at 15 V and the typical propagation is 60 ns at 10 V, which is the same figure as the quad OR and the quad AND because the extra inputs add capacitance rather than stages. A four input gate has roughly twice the input capacitance of a two input gate, and that is the number that slows a wide OR tree rather than the gate delay itself.

The noise margin of 1 V at 5 V, 2 V at 10 V and 2.5 V at 15 V is quoted over the full temperature range, and the input current of 1 microamp at 18 V is the leakage a driving stage has to supply. On a 5 V rail the guaranteed sink current falls to about 1 mA, so the part drives a CMOS input comfortably and a bipolar base only with a calculated resistor.

The headline 20 V rating, the 18 V operating limit and the 15 V top of the parametric table are three different numbers. The absolute maximum is 20.5 V, so a 20 V rail is inside the stress limit and outside the recommended range, and the page reports that rather than presenting one range for all three.

Where the wide OR function is the right choice

A four input OR in one gate saves a combiner stage. Four alarm lines, four limit switches or four enable signals can be combined with one package instead of two, and each removed stage removes a propagation delay and a solder joint. The cost is that the four inputs cannot be separated later, so a board that may need to mask one source has to put a jumper or a spare gate in front of it. That trade is the one to settle before the bill of materials is frozen, because the plastic DIP is 181.42 square millimetres and the SOIC is 51.9, and moving body later changes the footprint.

The thermal impedance of the plastic DIP in this family is 80 degrees per watt, the SOIC 86, the SOP 76 and the TSSOP 113. At static currents none of them is a constraint. The number becomes real when the output drives a long cable and the gate is asked to sink a surge, which is a fault case rather than an operating case, and the wider body has the lower rise for the same surge, which is the reason the DIP stays on older boards that are prone to field transients.

What the documents do not publish

The page has no maximum propagation delay, no output capacitance and no short circuit rating. The data sheet carries the switching table at three rails and the truth table, and the truth table is what a test engineer needs first: a four input OR is high when any input is high, which sounds obvious until a board mixes an active low signal into the tree. The page prints the function in the descriptor and leaves the table to the document. The 14-lead body is shared by the whole family, so the footprint cannot tell the three functions apart.

Second source and long term availability

The package choice also sets the repair path. A through hole board can be reworked with a soldering iron and a socket, and the 25 piece tube keeps a spare on the shelf for years. A surface mount board on a 2500 piece reel is cheaper per unit and harder to repair, because the reel is the only live SOIC format and a single replacement part is a cut tape piece from a distributor rather than a stocked tube. Buyers who keep equipment in the field for a decade should price that difference before they choose the body.

The CD4072B is second sourced under the same number and the 14-lead pin out is common across vendors. The nearest functional alternative is a 74HC4072 or a pair of 74HC32 gates, and both change the input threshold and the delay, so a timing path that leans on the 60 ns figure has to be rechecked. The obsolete part cross reference hub collects the equivalence checks, and the safety stock planning page covers how much of a live reel to hold when the tube rows are closed.

What to send with an enquiry

Send the string, the body, the quantity and the date. If the board is through hole, the 25 piece tube is the packing and a 400 piece build is sixteen tubes. If the board is surface mount and the quantity is under 2500, say so, because the only live SOIC format is the full reel and the alternatives are a partial reel or the TSSOP tube at 90 pieces. The BOM scrubbing page explains how those pack sizes are reconciled against a build quantity before a schedule is promised.